Onkyo PR-5507 Owners Manual

Onkyo PR-5507 Manual

Get Onkyo PR-5507 PDF manuals and user guides View all Onkyo PR-5507 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo PR-5507 manual content summary:

  • Onkyo PR-5507 | Owners Manual - Page 1
    Thank you for purchasing an Onkyo AV Controller. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Controller. Please retain this
  • Onkyo PR-5507 | Owners Manual - Page 2
    the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water
  • Onkyo PR-5507 | Owners Manual - Page 3
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • Onkyo PR-5507 | Owners Manual - Page 4
    on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT The wires in the mains lead are coloured in accordance with responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards
  • Onkyo PR-5507 | Owners Manual - Page 5
    Contents Introduction Important Safety Instructions 2 Precautions 3 Supplied Accessories 4 Features 6 Front & Rear Recorder 143 Activities Setup 144 Learning Commands 146 Using Normal Macros 147 Others Troubleshooting 148 Specifications 154 Video Resolution Chart 155 * To reset the AV
  • Onkyo PR-5507 | Owners Manual - Page 6
    ) • Dolby Volume*3 • Audyssey MultEQ® XT*8 to Correct Room Acoustic Problems • Audyssey Dynamic EQ™*8 for Loudness Correction • Audyssey Dynamic Volume™*8 • Crossover ) are required to receive the SIRIUS or XM satellite radio service. All programming and fees subject to change. It is prohibited
  • Onkyo PR-5507 | Owners Manual - Page 7
    Corporation. * Rhapsody and the Rhapsody logo are registered trademarks of RealNetworks, Inc. * "DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance." * Re-Equalization and the "Re-EQ" logo are trademarks of THX Ltd
  • Onkyo PR-5507 | Owners Manual - Page 8
    Front & Rear Panels Front Panel B CDEFG H I J Front flap Pull here to open the flap The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. B ON/STANDBY button (43
  • Onkyo PR-5507 | Owners Manual - Page 9
    button (68) This button is used when storing or deleting radio presets. S TUNING MODE button (67) This button is used to select the Auto or Manual tuning mode. T Arrow, TUNING, PRESET and ENTER buttons When the AM or FM input source is selected, the TUNING [R]/[X] buttons are used to tune the
  • Onkyo PR-5507 | Owners Manual - Page 10
    Tuning indicators RDS (European models) (69): Lights when tuned to a radio station that supports RDS (Radio Data System). AUTO (67): Lights when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected. TUNED (67): Lights when tuned to a radio station. FM STEREO
  • Onkyo PR-5507 | Owners Manual - Page 11
    Front & Rear Panels-Continued F SLEEP indicator (64) Lights when the Sleep function has been set. G Bi AMP indicator (21) Lights when the "Speakers Type(Front)" setting is set to "Bi-Amp". H Headphone indicator (64) Lights when a pair of headphones are plugged into the PHONES jack. I Message area
  • Onkyo PR-5507 | Owners Manual - Page 12
    Front & Rear Panels-Continued H V REMOTE CONTROL This V (Remote Interactive) jack can be connected to an V jack on another Onkyo AV component. The AV controller's remote controller can then be used to control that component. To use V, you must make an analog audio connection (RCA) between the AV
  • Onkyo PR-5507 | Owners Manual - Page 13
    Front Speakers" on page 21. ( SIRIUS antenna (North American models) This jack is for connecting a SIRIUS Satellite Radio antenna, sold separately (see the separate SIRIUS instructions). See pages 18 to 42 for connection information. 13
  • Onkyo PR-5507 | Owners Manual - Page 14
    Remote Controller Installing the Batteries 1 To open the battery compartment, press the small lever and remove the cover. Aiming the Remote Controller To use the remote controller, point it at the AV controller's remote control sensor, as shown below. Transmission Remote control sensor AV
  • Onkyo PR-5507 | Owners Manual - Page 15
    Remote Controller-Continued Controlling the AV Controller To control the AV controller, press the [RECEIVER] button to select Receiver mode. You can also use the remote controller to control your DVD/BD player, CD player, and other components. See pages 133 to 147 for more details. B C J3 D E
  • Onkyo PR-5507 | Owners Manual - Page 16
    Remote Controller-Continued ■ Controlling the tuner To control the AV controller's tuner, press the [TUNER] (or [RECEIVER]) button. You can select AM or FM by pressing the [TUNER] button repeatedly. 1 Arrow [R]/[X] buttons Used to tune into radio stations. 2 D.TUN button (67) (TUNER remote mode only
  • Onkyo PR-5507 | Owners Manual - Page 17
    About Home Theater Enjoying Home Theater Thanks to the AV controller's superb capabilities, you can enjoy surround sound with a real sense of movement in your own home-just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog or digital TV, you
  • Onkyo PR-5507 | Owners Manual - Page 18
    . To get the best from your surround sound system, you need to set the speaker settings. You can do this automatically (see page 56) or manually (see page 90). Note: Front high and front wide speakers produce no sound at the same time. Connecting Powered Subwoofers Using a suitable cable, connect
  • Onkyo PR-5507 | Owners Manual - Page 19
    RCA input jacks by using a multichannel RCA audio cable or several stereo RCA audio cables. See your multichannel power amplifier's instruction manual for more information on connecting speakers. AV controller FRONT HIGH/ FRONT WIDE RIGHT SURROUND BACK RIGHT SURROUND RIGHT FRONT RIGHT CENTER
  • Onkyo PR-5507 | Owners Manual - Page 20
    several XLR audio cables. The AV controller's balanced PRE OUT XLR jacks are wired as shown. See your multichannel power amplifier's instruction manual for more information on connecting speakers. AV controller FRONT HIGH/ FRONT WIDE RIGHT SURROUND BACK RIGHT SURROUND RIGHT FRONT RIGHT CENTER
  • Onkyo PR-5507 | Owners Manual - Page 21
    (high) and woofer (low) terminals. • Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual. See your multichannel power amplifier's instruction manual for more information on connecting speakers. AV controller SURROUND BACK RIGHT SURROUND RIGHT FRONT RIGHT
  • Onkyo PR-5507 | Owners Manual - Page 22
    Connecting the AV controller-Continued Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV controller won't pick up any radio signals without any antenna connected,
  • Onkyo PR-5507 | Owners Manual - Page 23
    . ■ Using a TV/FM Antenna Splitter It's best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown. Outdoor AM antennas work best when installed outside horizontally, but good results can
  • Onkyo PR-5507 | Owners Manual - Page 24
    Connecting the AV controller-Continued About AV Connections • Before making any AV connections, read the manuals supplied with your other AV components. • Don't connect the power cord until you've completed and double-checked all AV connections. Optical Digital Jacks The
  • Onkyo PR-5507 | Owners Manual - Page 25
    Coaxial digital audio cable Balanced XLR cable Analog audio cable (RCA) OPTICAL L R Multichannel analog audio cable (RCA) The AV controller does not support SCART plugs. Offers the best sound quality and allows you to enjoy surround sound (e.g., Dolby Digital, DTS). The audio quality is the same
  • Onkyo PR-5507 | Owners Manual - Page 26
    Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS Express, DTS-HD High Resolution Audio, DTS-HD Master Audio) Your DVD/BD players must also support HDMI output of the above audio formats. ■ Onkyo for System Control , which stands for Remote Interactive over HDMI, is the name of the system
  • Onkyo PR-5507 | Owners Manual - Page 27
    connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. 27
  • Onkyo PR-5507 | Owners Manual - Page 28
    formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide. Video Connection Formats Video equipment can be connected to the AV controller by using any one of the following
  • Onkyo PR-5507 | Owners Manual - Page 29
    input signals as they are. Composite MONITOR OUT S-Video Component HDMI Both: Video signals are output from both HDMI outputs at the resolution supported by both TVs. You cannot select "Resolution" setting. The picture adjust setting will be that for "HDMI Main". TV, projector, etc. Both
  • Onkyo PR-5507 | Owners Manual - Page 30
    Connecting the AV controller-Continued Audio Connection Formats Audio equipment can be connected to the AV controller by using any of the following audio connection formats: analog, optical, coaxial, analog multichannel, or HDMI. When choosing a connection format, bear in mind that the AV
  • Onkyo PR-5507 | Owners Manual - Page 31
    Connecting the AV controller-Continued Connecting a TV or Projector See "Connecting Components with HDMI" on page 25 for HDMI connection information. Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection
  • Onkyo PR-5507 | Owners Manual - Page 32
    Connecting the AV controller-Continued Connecting a DVD Player See "Connecting Components with HDMI" on page 25 for HDMI connection information. Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. You must connect the AV
  • Onkyo PR-5507 | Owners Manual - Page 33
    Connecting the AV controller-Continued Hooking Up the Multichannel Input If your DVD player supports multichannel audio formats such as DVD-Audio and Super Audio CD, and it has a multichannel analog audio output, you can connect it to the AV
  • Onkyo PR-5507 | Owners Manual - Page 34
    Connecting the AV controller-Continued Connecting a VCR or DVD Recorder for Playback Hint! With this hookup, you can use your VCR's tuner to listen to your favorite TV programs via the AV controller, useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that
  • Onkyo PR-5507 | Owners Manual - Page 35
    going through the AV controller, connect the TV/VCR's audio and video outputs directly to the recording VCR's audio and video inputs. See the manuals supplied with your TV and VCR for details. • Video signals connected to composite video inputs can only be recorded via composite video outputs. If
  • Onkyo PR-5507 | Owners Manual - Page 36
    Connecting the AV controller-Continued Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source Hint! With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV controller, useful if your TV has no audio outputs. Step 1:
  • Onkyo PR-5507 | Owners Manual - Page 37
    Connecting the AV controller-Continued Connecting a Game Console Step 1: Video Connection Choose a video connection that matches your game console ( A , B , or C ), and then make the connection. You must connect the AV controller to your TV with the same type of connection. Step 2: Audio
  • Onkyo PR-5507 | Owners Manual - Page 38
    Connecting the AV controller-Continued Connecting a Camcorder or Other Device Step 1: Video Connection Make the connection A . Step 2: Audio Connection Choose an audio connection that matches your camcorder ( a or b ), and then make the connection. Connection A a b AV controller AUX1 INPUT VIDEO
  • Onkyo PR-5507 | Owners Manual - Page 39
    to the AV controller's PHONO IN L/R jacks. • You can also use a phono equalizer to connect a turntable with an MC-type cartridge. See your phono equalizer's manual for details. AUDIO OUTPUT L R Turntable (MM) with no phono preamp built-in 39
  • Onkyo PR-5507 | Owners Manual - Page 40
    Connecting the AV controller-Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches the recorder ( a , b or c ), and then make the connection. • With connection a , you can play and record or listen in Zone 2 or Zone 3. • To connect the recorder
  • Onkyo PR-5507 | Owners Manual - Page 41
    -Continued Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock's instruction manual. ■ If Your iPod Supports Video: Connect your RI Dock's audio output jacks to the AV controller's GAME IN or VCR/DVR IN
  • Onkyo PR-5507 | Owners Manual - Page 42
    cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your other Onkyo components. • While interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV controller into a different branch circuit. • Do not use
  • Onkyo PR-5507 | Owners Manual - Page 43
    Turning On the AV controller (North American models) ON/STANDBY STANDBY indicator (European and Asian models) ON/STANDBY STANDBY indicator STANDBY ON RECEIVER Turning On and Standby POWER 1 (European and Asian models) Set the [POWER] switch to the ON position ( ). 2 AV controller Remote
  • Onkyo PR-5507 | Owners Manual - Page 44
    before using the AV controller for the very first time. Monitor Setup ■ Change "Monitor Out" setting manually If you connect your TV to HDMI OUT MAIN, "Monitor Out" setting is automatically set so that picture resolution as necessary to match the resolution supported by your TV (see page 47). 44
  • Onkyo PR-5507 | Owners Manual - Page 45
    to the menu will be in the same language as the Instruction Manual. The default Language setting for the onscreen menu is English. If your Instruction Manual is in a language other than English, first follow the instructions below to change the Language. Selecting the Language used for the
  • Onkyo PR-5507 | Owners Manual - Page 46
    First Time Setup-Continued ENTER SETUP RECEIVER RXFS Using the Onscreen Setup Menus Carry out the settings for the AV controller by using the Onscreen Setup Menu. 1 Press the [RECEIVER] button fol- lowed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear,
  • Onkyo PR-5507 | Owners Manual - Page 47
    AV controller upconvert the picture resolution as necessary to match the resolution supported by your TV. 1 Press the [RECEIVER] button, followed by SUB. Video signals are output from both HDMI outputs at the resolution supported by both TVs. Both (Main): Select this if your TVs are connected
  • Onkyo PR-5507 | Owners Manual - Page 48
    AV controller at the same resolution and with no conversion. Auto* : Select this to have the AV controller automatically convert video at resolutions not supported by your TV. 480p (480p/576p): Select this for 480p or 576p output and video conversion as necessary. Notes: • See page 28 for charts
  • Onkyo PR-5507 | Owners Manual - Page 49
    First Time Setup-Continued Video Input Setup 4 HDMI Input Setup If you connect a video component to HDMI IN, you must assign that input to an input selector. For example, if you connect your DVD/BD player to HDMI IN 1, you must assign HDMI IN 1 to the DVD/BD input selector. If you've connected
  • Onkyo PR-5507 | Owners Manual - Page 50
    ] button, arrow buttons, and [ENTER] button. ■ About PC Input Signals from PC INPUT ANALOG RGB are output from the HDMI output without the resolution conversion. Supported Resolution: • VGA (640 × 480) 60/72/75/85 Hz • SVGA (800 × 600) 56/60/72/75/85 Hz • XGA (1024 × 768) 60/70/75/85
  • Onkyo PR-5507 | Owners Manual - Page 51
    First Time Setup-Continued Digital Audio Input Setup If you connect a component to a digital input jack, you must assign that jack to an input selector. For example, if you connect your CD player to the OPTICAL IN1 jack, you should assign that jack to the CD input selector. By default, the COAXIAL
  • Onkyo PR-5507 | Owners Manual - Page 52
    First Time Setup-Continued Analog Audio Input Setup 4 If you connect a component to the AV controller's analog multichannel input, you must assign that input to an input selector. For example, if you connect your DVD/ BD player to the multichannel input, you must assign it to the DVD/BD input
  • Onkyo PR-5507 | Owners Manual - Page 53
    First Time Setup-Continued Speaker Settings If you change these settings, you must run Audyssey MultEQ® XT Room Correction and Speaker Setup again (see page 56). If you've fed your front speakers from the FRONT L/R and SURR BACK L/R outputs for bi-amping, you must change the "Speakers Type(Front
  • Onkyo PR-5507 | Owners Manual - Page 54
    First Time Setup-Continued TV Format Setup (European and Asian models) For the onscreen setup menus to display properly, you must specify the TV system used in your area. 1 Press the [RECEIVER] button fol- lowed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't
  • Onkyo PR-5507 | Owners Manual - Page 55
    First Time Setup-Continued 3 Use the Up and Down [R]/[X] but- tons to select "3. Tuner", and then press [ENTER]. The "Tuner" menu appears. (North American models) 7-3. Tuner FM/AM Frequency Step SAT Radio Mode 200kHz/10kHz None (European and Asian models) 7-3. Tuner AM Frequency Step
  • Onkyo PR-5507 | Owners Manual - Page 56
    ), and distances from the primary listening position. Audyssey MultEQ XT then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Enabling Audyssey
  • Onkyo PR-5507 | Owners Manual - Page 57
    First Time Setup-Continued Using Audyssey MultEQ® XT 1 ON/STANDBY 2 Speaker setup microphone ENTER RXFS 3 Notes: • If the AV controller is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup starts. • Room correction and speaker setup cannot be
  • Onkyo PR-5507 | Owners Manual - Page 58
    First Time Setup-Continued • Make the room as quiet as possible. 6 Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, 7 fluorescent lights, home appliances, light dimmers, or other devices. • Cell phones should be
  • Onkyo PR-5507 | Owners Manual - Page 59
    First Time Setup-Continued 9 10 When the calculations are complete, the following screen appears. MultEQ XT: Auto Setup -- Review SP Configuration -- Subwoofer No Front Full Band Center 40Hz Surround 120Hz Front Wide None Front High None Surr Back 150Hz Surr Back Ch 2ch Save
  • Onkyo PR-5507 | Owners Manual - Page 60
    First Time Setup-Continued MultEQ XT: Auto Setup Speaker Detect Error FL : Yes SL : --FWL : No FHL : Yes SBL : --C : Yes Retry Cancel FR : No SR : --FWR : No FHR : Yes SBR : --SW1 : --SW2 : --- One of the front speakers has not been detected. MultEQ XT: Auto Setup Speaker Detect Error FL :
  • Onkyo PR-5507 | Owners Manual - Page 61
    the level and/or distance of the main speakers. If this happens, THX recommends setting them manually. Using Powered Subwoofers If you're using powered subwoofers that output very low-frequency sound at a switch, set it to Off or Direct. Refer to your subwoofer's instruction manual for details. 61
  • Onkyo PR-5507 | Owners Manual - Page 62
    Basic Operations Selecting the Input Source This section explains how to select the input source (i.e., the AV component that you want to listen to or watch). MASTER VOLUME INPUT SELECTOR RECEIVER VOL R/X Input selector buttons 1 AV controller Remote controller or Use the AV controller's
  • Onkyo PR-5507 | Owners Manual - Page 63
    Basic Operations-Continued DISPLAY TONE, F, S DIMMER Press [RECEIVER] first. DISPLAY MUTING DIMMER SLEEP Adjusting the Bass & Treble You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected. 1 AV controller Press the [TONE
  • Onkyo PR-5507 | Owners Manual - Page 64
    Basic Operations-Continued Setting the Display Brightness You can adjust the brightness of the AV controller's display. Remote controller Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: • Normal + VOLUME light on. • Normal + VOLUME light off. • Dim + VOLUME
  • Onkyo PR-5507 | Owners Manual - Page 65
    Basic Operations-Continued Using Easy Macros Using the Easy macro command in the Easy macro mode, you can sequentially operate Onkyo components with simple commands by simply pressing one button. These commands are user-specifiable (see page 144) and the default actions are described below. Press
  • Onkyo PR-5507 | Owners Manual - Page 66
    Basic Operations-Continued Changing Source Component When you want to operate the component that is not assigned as the source component, you can assign it as the source component. For the default assignment, see page 145. (3 seconds) While holding down the REMOTE MODE button, press and hold down
  • Onkyo PR-5507 | Owners Manual - Page 67
    model changes FM/AM frequency in 200k/10k (or 50k/9k) Hz steps. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations , it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. ■ Tuning into Stations by
  • Onkyo PR-5507 | Owners Manual - Page 68
    Listening to the Radio-Continued Presetting AM/FM Stations MEMORY PRESET F/S AV controller To select a preset, use the PRESET [F]/[S] buttons, or the remote controller's CH [+/-] button. or Remote controller You can store a combination of up to 40 of your favorite AM/FM radio stations as presets
  • Onkyo PR-5507 | Owners Manual - Page 69
    information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV controller supports four types of RDS information: PS (Program Service) When tuned to an RDS station that's broadcasting PS information, the station's name will be displayed. Pressing the [DISPLAY
  • Onkyo PR-5507 | Owners Manual - Page 70
    Listening to the Radio-Continued When tuned to an RDS station that's broadcasting text information, the text can be displayed. Displaying Radio Text (RT) RT/PTY/TP 3 To start the search, press [ENTER]. The AV controller searches until it finds a station of the type you specified, at which
  • Onkyo PR-5507 | Owners Manual - Page 71
    site at: http://www.onkyo.com iPod adapter Dock connector Compatible iPod models For information about which iPod models are supported by the UP-A1 Dock, see the UP-A1 Dock instruction manual. Note: Before using the UP-A1 Dock, update your iPod with the latest software, available from the Apple Web
  • Onkyo PR-5507 | Owners Manual - Page 72
    iPod models and generations, certain but- tons may not work as expected. • For detailed operation of the iPod, please refer to the instruction manual. 72 B Arrow [R]/[X] and ENTER buttons Used to navigate menus and select items. C Previous [] button Restarts the current song. Press it again to
  • Onkyo PR-5507 | Owners Manual - Page 73
    UP-A1 Dock for iPod-Continued Status messages ❏ PORT Reading The AV controller is checking the connection with the dock. ❏ PORT Not Support The AV controller do not support the connected dock. ❏ PORT UP-A1 UP-A1 Dock is connected. Notes: • The AV controller displays the message "UP-A1" for several
  • Onkyo PR-5507 | Owners Manual - Page 74
    Recording This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources
  • Onkyo PR-5507 | Owners Manual - Page 75
    Using the Listening Modes Selecting Listening Modes See "About the Listening Modes" on page 83 for detailed information about the listening modes. • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV controller with a digital audio connection (
  • Onkyo PR-5507 | Owners Manual - Page 76
    Using the Listening Modes-Continued Listening Modes Available for Each Source Format The Speaker layout illustration shows which speakers are set to active in the "Speaker Configuration" setting (see page 90). The LISTENING MODE button illustration shows that listening modes can be selected. FL :
  • Onkyo PR-5507 | Owners Manual - Page 77
    Using the Listening Modes-Continued Stereo Source (1/2) Listening Mode Button Pure Audio*3 Direct Stereo Mono PLII/PLIIx Movie*1 PLII/PLIIx Music*1 PLII/PLIIx Game*1 PLIIz Height Neo:6 Cinema Neo:6 Music Neural Surround Neural Digital Music PLII/PLIIx Movie*1 THX Cinema PLII/PLIIx Movie Audyssey
  • Onkyo PR-5507 | Owners Manual - Page 78
    Using the Listening Modes-Continued Stereo Source (2/2) Listening Mode Button ✔: Available Listening Modes Speaker layout LH RH LH RH LH RH LH RH LW FL C FR RW LW FL C FR RW LW FL C FR RW LW FL C FR RW SW SW SW SW SW SW SW SW SL SR SL SR SL SR SL SR PLII/PLIIx Game*1 THX
  • Onkyo PR-5507 | Owners Manual - Page 79
    Using the Listening Modes-Continued 5.1 channel Sources (1/3) Listening Mode Button ✔: Available Listening Modes Speaker layout LH RH LH RH LH RH LH RH LW FL C FR RW LW FL C FR RW LW FL C FR RW LW FL C FR RW SW SW SW SW SW SW SW SW SL SR SL SR SL SR SL SR Pure Audio*3
  • Onkyo PR-5507 | Owners Manual - Page 80
    Using the Listening Modes-Continued 5.1 channel Sources (2/3) Listening Mode Button ✔: Available Listening Modes Speaker layout LH RH LH RH LH RH LH RH LW FL C FR RW LW FL C FR RW LW FL C FR RW LW FL C FR RW SW SW SW SW SW SW SW SW SL SR SL SR SL SR SL SR PLIIx Music THX
  • Onkyo PR-5507 | Owners Manual - Page 81
    Using the Listening Modes-Continued 5.1 channel Sources (3/3) Listening Mode Button ✔: Available Listening Modes Speaker layout LH RH LH RH LH RH LH RH LW FL C FR RW LW FL C FR RW LW FL C FR RW LW FL C FR RW SW SW SW SW SW SW SW SW SL SR SL SR SL SR SL SR SBL SBR SBL
  • Onkyo PR-5507 | Owners Manual - Page 82
    Using the Listening Modes-Continued 7.1 channel Sources Listening Mode Button Pure Audio*3 Direct Stereo Mono Multichannel/ DolbyDigital Plus/TrueHD/ DTS-HD High Resolution Audio/DTS-HD Master Audio/ DTS-ES Discrete*4/ DTS-ES Matrix*4 PLIIz Height Audyssey DSX*2 THX Cinema PLIIz Height THX
  • Onkyo PR-5507 | Owners Manual - Page 83
    Using the Listening Modes-Continued Notes: *1 Based on the audio channels contained in the source, the corresponding speakers will output the sound. *2 This listening mode can be selected only when all the following conditions are satisfied: a. Center speaker is connected to the power amplifier. b.
  • Onkyo PR-5507 | Owners Manual - Page 84
    and HD DVD, this is the latest multichannel audio format from Dolby. It supports up to 7.1 channels with 48 kHz sampling rate. Dolby TrueHD Designed to and HD DVD, this is the latest multichannel audio format from DTS. It supports up to 7.1 channels with 96 kHz sampling rate. DTS-HD Master Audio
  • Onkyo PR-5507 | Owners Manual - Page 85
    Using the Listening Modes-Continued THX Founded by George Lucas, THX develops stringent standards that ensure movies are reproduced in movie theaters and home theaters just as the director intended. THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for
  • Onkyo PR-5507 | Owners Manual - Page 86
    Advanced Setup Onscreen Setup Menus The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV controller's various settings. Settings are organized into nine categories on the main menu, most containing a submenu. Main menu Submenus pages 87-88 Menu 1.
  • Onkyo PR-5507 | Owners Manual - Page 87
    Advanced Setup-Continued Input/Output Assign This section explains items on the "Input/Output Assign" menu. 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV
  • Onkyo PR-5507 | Owners Manual - Page 88
    Advanced Setup-Continued Component Video Input See "Component Video Input Setup" on page 50. Digital Audio Input See "Digital Audio Input Setup" on page 51. Analog Audio Input Multich See "Analog Audio Input Setup" on page 52. Subwoofer Input Sensitivity 0 dB (default), 5 dB, 10 dB, 15 dB
  • Onkyo PR-5507 | Owners Manual - Page 89
    Gamma0 Gamma1 Gamma2 Gamma3 Gamma4 Gamma5 Gamma6 Gamma7 Gamma8 Gamma9 Advanced Setup-Continued Gamma Curve The color range and the brightness characteristic of a reproduced image depend on the TV or projector. With this setting, you can adjust the balance of the color signals (R, G, and B). To view
  • Onkyo PR-5507 | Owners Manual - Page 90
    and Speaker Setup (see page 56). Here you can check the settings made by Audyssey MultEQ® XT Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ® XT Room Correction and Speaker Setup. Note: The Speaker Setup
  • Onkyo PR-5507 | Owners Manual - Page 91
    Advanced Setup-Continued LPF of LFE (Low-Pass Filter for the LFE Channel) 80Hz(THX) (default), 90Hz, 100Hz, 120Hz This setting is not set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup (see page 56). With this setting, you can specify the cutoff frequency of the LFE channel
  • Onkyo PR-5507 | Owners Manual - Page 92
    the Direct or Pure Audio listening mode is selected, the equalizer settings have no effect. Equalizer Manual: You can adjust the equalizer for each speaker manually. If you selected "Manual", continue with this procedure. 1 Press the Down [X] button to select "Channel", and then use the Left
  • Onkyo PR-5507 | Owners Manual - Page 93
    Advanced Setup-Continued THX Audio Setup This setting is not set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup (see page 56). With the "SurrBack Sp Spacing" setting, you can specify the distance between your surround back speakers. If you're using a THX-certified subwoofer,
  • Onkyo PR-5507 | Owners Manual - Page 94
    Advanced Setup-Continued Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate
  • Onkyo PR-5507 | Owners Manual - Page 95
    only. Note: If the "Front High" and "Front Wide" settings are set to other than "None" (page 90), this setting is fixed at "Manual". Dolby Volume Off: Dolby Volume off (default). Low: Low Compression Mode becomes active. Mid: Medium Compression Mode becomes active. High: High Compression Mode
  • Onkyo PR-5507 | Owners Manual - Page 96
    Dynamic EQ™ on. With Audyssey Dynamic EQ™, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct
  • Onkyo PR-5507 | Owners Manual - Page 97
    Advanced Setup-Continued Theater-Dimensional Listening Angle Wide: Select if the listening angle is greater than 30 degrees (default). Narrow: Select if the listening angle is less than 30 degrees. With this setting, you can optimize the Theater-Dimensional listening mode by specifying the angle
  • Onkyo PR-5507 | Owners Manual - Page 98
    ] button. A/V Sync 0 ms to 250 ms in 5 ms steps (default: 0 ms) If HDMI Lip Sync is enabled (see page 108), and your TV or display supports HDMI Lip Sync, the displayed delay time will be the summation of the A/V Sync delay time and the HDMI Lip Sync delay time. The HDMI
  • Onkyo PR-5507 | Owners Manual - Page 99
    Advanced Setup-Continued Name Edit You can enter a custom name for each individual input selector (excluding TUNER) and radio preset for easy identification. When entered, the custom name will appear on the display. Notes: • To name a radio preset, use the [TUNER] button to select AM or FM, and
  • Onkyo PR-5507 | Owners Manual - Page 100
    Advanced Setup-Continued Zoom Mode This setting determines the aspect ratio. Normal: Full: (default) Zoom: Wide Zoom: 100
  • Onkyo PR-5507 | Owners Manual - Page 101
    quality. If the AV controller detects the type of content incorrectly due to characteristics of the disc, you can select Video or Film manually. Edge Enhancement*2 Off: Edge enhancement off (default). Low: Low edge enhancement. Mid: Medium edge enhancement. High: High edge enhancement. With Edge
  • Onkyo PR-5507 | Owners Manual - Page 102
    controller at the same resolution and with no conversion (default). Auto: Select this to have the AV controller automatically convert video at resolutions not supported by your TV. When the "Monitor Out" is set to "Analog", this setting will be changed to "Through". 480p (480/576p): Select this for
  • Onkyo PR-5507 | Owners Manual - Page 103
    Advanced Setup-Continued Red Brightness*2 -50 to +50 (default: 0) With this setting you can adjust the picture red brightness. "-50" is the darkest. "+50" is the brightest. Red Contrast*2 -50 to +50 (default: 0) With this setting you can adjust red contrast. "-50" is the least. "+50" is the
  • Onkyo PR-5507 | Owners Manual - Page 104
    Advanced Setup-Continued Assigning Listening Modes to Input Sources You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals.
  • Onkyo PR-5507 | Owners Manual - Page 105
    Advanced Setup-Continued Miscellaneous (Volume/OSD) Setup This section explains the items on the "Miscellaneous" menu. 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected
  • Onkyo PR-5507 | Owners Manual - Page 106
    Advanced Setup-Continued OSD Setup Immediate Display On: Displayed (default). Off: Not displayed. This preference determines whether operation details are displayed onscreen when an AV controller function is adjusted. Even when "On" is selected, operation details may not be output if the input
  • Onkyo PR-5507 | Owners Manual - Page 107
    models) The ID of the Sirius Connect Home Tuner is displayed here. You must sign up to obtain a SIRIUS ID. See the separate Satellite Radio Guide for more information. SIRIUS Parental Lock (North American models) This item is for use with SIRIUS Satellite Radio. It's not available if "SAT Radio Mode
  • Onkyo PR-5507 | Owners Manual - Page 108
    the setting to "Disable". • Refer to the connected component's instruction manual for details. • If the "Monitor Out" setting is set to "Both (Main)" or "Both (Sub)" (page 47) and if your TV connected to a priority output does not support x.v.Color, output will be without x.v.Color control. 108
  • Onkyo PR-5507 | Owners Manual - Page 109
    is compatible or not. • Set it to "Off" if the operation is not successful. • Refer to the connected component's instruction manual for details. • The control does not support HDMI OUT SUB. Use HDMI OUT MAIN instead. Power Control On: Power Control enabled. Off: Power Control disabled. To
  • Onkyo PR-5507 | Owners Manual - Page 110
    Advanced Setup-Continued Network See "Network Settings" on page 121. Firmware Update Notes: • Perform the firmware update only when an announcement is posted on the Onkyo Web site. • It takes about 60 minutes to complete the firmware update. • When updating a firmware from a USB mass storage
  • Onkyo PR-5507 | Owners Manual - Page 111
    , the AV controller detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS: • If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM
  • Onkyo PR-5507 | Owners Manual - Page 112
    Advanced Setup-Continued Using the Audio Settings You can change various audio settings by pressing the [AUDIO] button. RECEIVER RXFS AUDIO 1 Press the [RECEIVER] button followed by the [AUDIO] button. The audio setting items appear on the display. 2 Use the Up and Down [R]/[X] buttons to select
  • Onkyo PR-5507 | Owners Manual - Page 113
    Dynamic EQ™ and Audyssey Dynamic Volume™ will be set to "Off" from "Audyssey" and "Equalizer" setting will be set to "Off" or remain set to "Manual". • If you would like to use Dolby Volume in THX listening modes, set "Loudness Plus" setting to "Off" and set "Preserve THX Settings " setting to
  • Onkyo PR-5507 | Owners Manual - Page 114
    Advanced Setup-Continued Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV controller is set to Standby. To save the setting you made here, go to "Level Calibration" on page 92 before setting the AV
  • Onkyo PR-5507 | Owners Manual - Page 115
    the Web. Consult your ISP if you have any problems with your Internet connection. • The AV controller uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see page 121. • The AV controller does not support PPPoE settings, so if you have a PPPoE
  • Onkyo PR-5507 | Owners Manual - Page 116
    When the program setting is finished, go to step 3. Notes: • When it flashes, confirm the network connection. • Services available may vary depend- ing on the region. See the separate instructions for more information. On your computer, start your Web browser and enter the AV controller's IP address
  • Onkyo PR-5507 | Owners Manual - Page 117
    The search function does not work with media servers which do not support this function. • Depending on the sharing settings in the media server, the AV controller may not able to access the content. Refer to the instruction manual of the media server. 4 5 or Use the Up and Down [R]/[X] buttons to
  • Onkyo PR-5507 | Owners Manual - Page 118
    been played once, they'll all be played again in a different random order. To cancel random playback, press the [RANDOM] button again. Random playback supports up to 20,000 songs per folder. If a folder contains more than this, songs over 20,000 are not included in random playback. Repeat Playback
  • Onkyo PR-5507 | Owners Manual - Page 119
    Number of channels: 2 • Variable bit-rate (VBR) MP3 files are supported. (Playing times may not display correctly.) • MP3 files must have a , 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. Incompatible files cannot be played. • Quantization bit: 8 bit, 16 bit, 24 bit • Number
  • Onkyo PR-5507 | Owners Manual - Page 120
    NET/USB-Continued Server Requirements The AV controller can play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows
  • Onkyo PR-5507 | Owners Manual - Page 121
    : When modifying network settings, after modifying it is necessary to execute "Save". This section explains how to configure the AV controller's network settings manually. If your router's DHCP server is enabled, you don't need to change any of these settings, as the AV controller is set use
  • Onkyo PR-5507 | Owners Manual - Page 122
    some USB devices even if they conform to the USB mass storage device class. • USB devices formatted with the FAT16 or FAT32 file system are supported. • If the storage device has been partitioned, each section will be treated as an independent device. • Each folder may contain up to 20,000 music
  • Onkyo PR-5507 | Owners Manual - Page 123
    NET/USB-Continued Playing Music Files on a USB Device This section explains how to play music files on a USB mass storage device. NET/USB RECEIVER RXFS ENTER  1 Plug your USB mass storage device into the AV controller's USB port. 2 Press the [NET/USB] button repeatedly to select the USB(
  • Onkyo PR-5507 | Owners Manual - Page 124
    to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer your USB MP3 player's instruction manual for details. • Protected WMA music files on an MP3 player cannot be played. • Onkyo accepts no responsibility
  • Onkyo PR-5507 | Owners Manual - Page 125
    Multi Zone Multiroom Capability You can use three speaker systems with this AV controller-a surround-sound speaker system (up to 9.2 channels) in your main listening room, Zone 2: a stereo speaker system in a second room, Zone 3: a stereo speaker system in a third room. And, you can select a
  • Onkyo PR-5507 | Owners Manual - Page 126
    Multi Zone-Continued In addition to your main listening room, you can also enjoy playback in the other room, or as we call Multi Zone. And, you can select a different source for each room. Connecting Zone 2 Zone 2 speakers must be connected to an amp in Zone 2. Connecting Your Zone 2 Speakers You
  • Onkyo PR-5507 | Owners Manual - Page 127
    Multi Zone-Continued Connecting Zone 3 Zone 3 speakers must be connected to an amp in Zone 3. Connecting Your Zone 3 Speakers You can enjoy 2-channel stereo playback in Zone 3 and a different source to those selected for your main room and Zone 2. Hookup • Use an RCA audio cable to connect the AV
  • Onkyo PR-5507 | Owners Manual - Page 128
    Multi Zone-Continued Setting the Multi Zone 1 Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [R]/[X] buttons to select "7.
  • Onkyo PR-5507 | Owners Manual - Page 129
    Multi Zone-Continued Using Zone 2/3 This section explains how to turn Zone 2/3 on and off, how to select an input source for Zone 2/3, and how to adjust the volume for Zone 2/3. Controlling Zone 2/3 from the AV controller ZONE 3 indicator ZONE 2 indicator Controlling Zone 2/3 with the Remote
  • Onkyo PR-5507 | Owners Manual - Page 130
    Multi Zone-Continued Notes: • Only analog input sources are output by the ZONE 2 PRE OUT and ZONE 3 PRE OUT. Digital input sources are not output. If no sound is heard when an input source is selected, check if it's connected to an analog input. • You cannot select different AM or FM radio stations
  • Onkyo PR-5507 | Owners Manual - Page 131
    Multi Zone-Continued Using the 12V Triggers 3 The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for
  • Onkyo PR-5507 | Owners Manual - Page 132
    Multi Zone-Continued Using the Remote Controller in Zone 2/3 and Multiroom Control Kits To control the AV controller with the remote controller while you're in Zone 2 or Zone 3, you'll need a commercially available multiroom remote control kit for each zone. • Multiroom kits are made by Niles and
  • Onkyo PR-5507 | Owners Manual - Page 133
    Controlling Other Components You can use the AV controller's remote controller (RC-747M) to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code for a component that you want to control: DVD, TV, VCR, etc. • Learn
  • Onkyo PR-5507 | Owners Manual - Page 134
    Controlling Other Components-Continued 5 Use the Up and Down [R]/[X] but- tons to select category, and then press [ENTER]. The brand name input panel appears. 8-1. Remote Mode Setup Category Brand TV TV ABCDEFGH I JKLM NOPQRS T UVWX Y Z 1 2 3 4 5 6 7 8 9 0 -&@ Space Back Space Search 6
  • Onkyo PR-5507 | Owners Manual - Page 135
    Controlling Other Components-Continued Entering Remote Control Codes You'll need to enter a code for each component that you want to control. REMOTE MODE DISPLAY Number buttons 1 Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized
  • Onkyo PR-5507 | Owners Manual - Page 136
    Controlling Other Components-Continued Remote Control Codes for Onkyo Components Connected via V Onkyo components that are connected via V are controlled by pointing the remote controller at the AV controller, not the component. This allows you to control components that are out of view, in a rack,
  • Onkyo PR-5507 | Owners Manual - Page 137
    is preprogrammed with the remote con- trol code for controlling a TV that supports the *1 (limited to some models). The TV must be able to TV [INPUT] button Selects the TV's external inputs. E GUIDE button Displays the program guide. F Arrow [R]/[X]/[F]/[S] and ENTER buttons Used to navigate menus
  • Onkyo PR-5507 | Owners Manual - Page 138
    code for a differ- ent component, see page 135. The [DVD/BD] button is preprogrammed with the remote control code for controlling a component that supports the *1. The component must be able to receive remote control commands via and be connected to the AV controller via HDMI. If controlling
  • Onkyo PR-5507 | Owners Manual - Page 139
    , or select play modes. • Buttons marked with an asterisk (*) are not supported by the function. B ON, STANDBY buttons Set the video recorder to On VOL [R]/[X] button Adjust the TV's volume. F GUIDE button Displays the program guide or navigation list. G Arrow [R]/[X]/[F]/[S] and ENTER buttons
  • Onkyo PR-5507 | Owners Manual - Page 140
    appropriate REMOTE MODE button first. B H I J K C L D E M N O F G P B ON, STANDBY buttons Set the component to On or Standby. C GUIDE button Displays the onscreen program guide. D Arrow [R]/[X]/[F]/[S] and ENTER buttons Used to navigate menus and select items. E SETUP button Displays the
  • Onkyo PR-5507 | Owners Manual - Page 141
    Controlling Other Components-Continued Controlling a CD Player, CD Recorder or MD Recorder By pressing the REMOTE MODE button that's been programmed with the remote control code for your CD player, CD recorder, or MD recorder, you can control your player with the following buttons. The [CD] button
  • Onkyo PR-5507 | Owners Manual - Page 142
    to HDD or HDD/ DOCK. • Set the AV controller's Input Display to DOCK (see page 55). • See to the Dock's instruction manual for more information. Press the appropriate REMOTE MODE button first. B I J K L C M D N O E P F Q G R S H T B ON, STANDBY buttons Turns the iPod on or off
  • Onkyo PR-5507 | Owners Manual - Page 143
    Controlling Other Components-Continued S PLAY MODE button Selects play modes on components with selectable play modes. Works as a Resume button when used with a DS-A2 RI Dock. T RANDOM button Used with the shuffle function. Note: With some components, certain buttons may not work as expected, and
  • Onkyo PR-5507 | Owners Manual - Page 144
    Controlling Other Components-Continued Activities Setup 5 Via onscreen menu, you can specify what actions will be taken by the Easy macro command in the Easy macro mode. 1 Press the [RECEIVER] button fol- lowed by the [SETUP] button. The main menu appears onscreen. If the main menu doesn't
  • Onkyo PR-5507 | Owners Manual - Page 145
    Controlling Other Components-Continued Source Play 7 Enable: Start playback the source of "Enable". Disable: Start playback the source of "Disable". This option enables the Source to start playback when the ACTIVI- TIES button is pressed. Here are the default settings. Items Default
  • Onkyo PR-5507 | Owners Manual - Page 146
    Controlling Other Components-Continued Learning Commands The AV controller's remote controller can learn the commands of other remote controllers. By transmitting, for example, the Play command from your CD player's remote controller, the remote controller can learn it, and then transmit the exact
  • Onkyo PR-5507 | Owners Manual - Page 147
    Controlling Other Components-Continued Using Normal Macros You can program the remote controller's ACTIVITIES buttons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press the [RECEIVER] button to select the Receiver
  • Onkyo PR-5507 | Owners Manual - Page 148
    Troubleshooting If you have any trouble using the AV controller, look for a solution in this section. If the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off. • With some DVD-Video discs, you need to select an
  • Onkyo PR-5507 | Owners Manual - Page 149
    Troubleshooting-Continued The front high, front wide and surround back speakers • Check the digital audio output setting on the con- nected device. On some game consoles, such as those that support DVD, the default setting is off. • With some DVD-Video discs, you need to select an audio output format
  • Onkyo PR-5507 | Owners Manual - Page 150
    Troubleshooting-Continued Video There's no picture • Make sure that all video connecting video is output by the HDMI outputs. • When the "Resolution" (page 48) is set to any resolution not supported by the TV, no video is output by the HDMI outputs. • If the message "Resolution Error" appears on the
  • Onkyo PR-5507 | Owners Manual - Page 151
    Troubleshooting-Continued • Make sure you've selected the correct remote controller controller that cannot be used for learning? Some commands cannot be learned, especially those that contain several instructions. Dock for iPod There's no sound • Make sure your iPod is actually playing. • Make sure
  • Onkyo PR-5507 | Owners Manual - Page 152
    Troubleshooting-Continued Zone 2/3 There's no sound • Only components connected to USB device • Make sure the USB device is plugged in properly. • The AV controller supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices
  • Onkyo PR-5507 | Owners Manual - Page 153
    Troubleshooting-Continued The following settings can be made for the SVideo and composite video inputs You must use the buttons on the AV controller to make
  • Onkyo PR-5507 | Owners Manual - Page 154
    Specifications Amplifier Section Input Sensitivity and Impedance 200 mV/47 kΩ (LINE) 2.5 mV/47 kΩ, (PHONO MM) Output Level and Impedance 200 mV/470 Ω (REC OUT) Phono Overload 70 mV (MM 1 kHz 0.5 %) Frequency Response 5 Hz - 100 kHz/+1 dB - 3 dB (Direct mode) Tone Control ±10 dB, 50 Hz (
  • Onkyo PR-5507 | Owners Manual - Page 155
    Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV controller. NTSC ✔: Output Output HDMI COMPONENT Input 1080p 1080i HDMI 720p 480p 480i 1080p 1080i COMPONENT 720p 480p 480i S-VIDEO 480i COMPOSITE 480i 1080p ✔ ✔ ✔
  • Onkyo PR-5507 | Owners Manual - Page 156
    Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: +1-201-785-2600 Fax: +1-201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS GmbH
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
E
n
AV Controller
PR-SC5507
Instruction Manual
Thank you for purchasing an Onkyo AV Controller.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Controller.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connection
..................................
18
Turning On & First Time Setup
.....
43
Basic Operations
.........................
62
Using the Listening Modes
........
75
Advanced Setup
..........................
86
NET/USB
...................................
115
Multi Zone
................................
125
Controlling Other Components
....
133
Others
.........................................
148