Onkyo TX-DS575x Owner Manual - Page 37

Macro Direct Learning function, Follow Steps 2 in the Programming Macro Mode - code

Get Onkyo TX-DS575x PDF manuals and user guides View all Onkyo TX-DS575x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Using a Macro function 1, 3 1 Tip: The codes programmed into a MACRO button will be transmitted with an interval of 0.5 seconds. However, some devices may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, press one operation button, press the corresponding MODE button, then press another operation button to extend the interval between the two operations up to one second. Macro Direct Learning function A series of remote controller button operations can be memorized into the MACRO DIRECT button for one-touch control. Note: You can program only one series of button operations into the MACRO DIRECT button. 1. Press and hold down any one of the eight MODE buttons and press the MACRO DIRECT button. Then, release the buttons. When you press the MODE button, the SEND/LEARN indicator lights up. When you press the MACRO DIRECT button, the indicator turns off. When you release the buttons, the indicator flashes briefly, then lights up again. 2. Follow Steps 2 in the "Programming Macro Mode" on page 36. 3. Press the MACRO DIRECT button to complete the procedure. The SEND/LEARN indicator flashes twice slowly. 4. Check to see if the button has been programmed correctly. Point the RC-392M toward the TX-DS575X and press the MACRO DIRECT button, and make sure that the device responds as programmed. Transmitting the codes in Macro mode takes a while. During transmission, point the remote controller toward the device to be controlled. Note: • You may program up to 16 button operations into the MACRO DIRECT button. If you try to program the 17th step, it will be ignored. • If you do not press any button for more than 30 seconds during the procedure, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume Step 1. • If you make a mistake during programming, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume Step 1. • If you erase one of the operation buttons already programmed in the MACRO DIRECT button, or if you program a different code into such a button, the operation button will no longer work. In this case, program the buttons again to avoid malfunction. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
37
Using a Macro function
A series of remote controller button operations can be memorized
into the MACRO DIRECT button for one-touch control.
Note:
You can program only one series of button operations into the
MACRO DIRECT button.
1. Press and hold down any one of the eight MODE buttons
and press the MACRO DIRECT button. Then, release the
buttons.
When you press the MODE button, the SEND/LEARN indica-
tor lights up. When you press the MACRO DIRECT button, the
indicator turns off. When you release the buttons, the indicator
flashes briefly, then lights up again.
2.
Follow Steps 2 in the “Programming Macro Mode” on page
36.
3.
Press the MACRO DIRECT button to complete the proce-
dure.
The SEND/LEARN indicator flashes twice slowly.
4.
Check to see if the button has been programmed correctly.
Point the RC-392M toward the TX-DS575X and press the
MACRO DIRECT button, and make sure that the device
responds as programmed.
Transmitting the codes in Macro mode takes a while. During
transmission, point the remote controller toward the device to
be controlled.
Note:
•
You may program up to 16 button operations into the MACRO
DIRECT button. If you try to program the 17th step, it will be
ignored.
•
If you do not press any button for more than 30 seconds during
the procedure, the SEND/LEARN indicator flashes three times
quickly, then the RC-392M exits Learning mode. Resume Step
1.
•
If you make a mistake during programming, the SEND/LEARN
indicator flashes three times quickly, then the RC-392M exits
Learning mode. Resume Step 1.
•
If you erase one of the operation buttons already programmed in
the MACRO DIRECT button, or if you program a different
code into such a button, the operation button will no longer
work. In this case, program the buttons again to avoid malfunc-
tion.
Macro Direct Learning function
1, 3
1
Tip:
The codes programmed into a MACRO button will be
transmitted with an interval of 0.5 seconds. However,
some devices may not be able to complete one opera-
tion in 0.5 seconds and may miss the next code. In this
case, press one operation button, press the correspond-
ing MODE button, then press another operation button
to extend the interval between the two operations up to
one second.