Optoma BX-AL133 User Manual
Optoma BX-AL133 Manual
 |
View all Optoma BX-AL133 manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma BX-AL133 manual content summary:
- Optoma BX-AL133 | User Manual - Page 1
BX-AL133 Anamorphic Lens User's Manual - Optoma BX-AL133 | User Manual - Page 2
User's Manual BX-AL133 Safety 1. Read and understand instructions and heed warnings before beginning installation. 2. Mount rail securely. The lens is heavy, and requires a secure and stable surface. Fasteners in sheetrock alone are not safe. Reciprocal lens motion can and will work them loose. Use - Optoma BX-AL133 | User Manual - Page 3
User's Manual BX-AL133 Introduction Thank you for purchasing the Optoma BX-AL133 anamorphic lens. The lens and motorized sled is outfitted operation Configurable "lens in" position Extra external IR sensor for remote mounting (if needed) Input 12V jack for automatic lens trigger Output 12V - Optoma BX-AL133 | User Manual - Page 4
Manual BX-AL133 Getting to Know Your System Motorized Sled Status LED Infrared Remote Sensor Mounting Plate Rail Reversable Logo Plate Motor Housing Cover Remote IR Sensor 8-Button Remote Control OFF ON LENS OUT LENS IN PANEL OFF PANEL ON SLOW FAST Drive Belt Rail Bearing (X4) Lens - Optoma BX-AL133 | User Manual - Page 5
User's Manual BX-AL133 Plan Your Installation The lens assembly may be mounted in one of two ways: 1. To the ceiling or projector mount above the projector 2. To a shelf or table below the projector When attaching the motor assembly to the ceiling, use a board, plate or lens-enabled projector - Optoma BX-AL133 | User Manual - Page 6
of the BX-AL133 expansion lens. Before starting, the projector must be correctly focused with the zoom and iris set in their viewing positions. This will assure that the front of the lens is positioned correctly. Hold the motorized sled up to the projector and determine if the LENS IN position - Optoma BX-AL133 | User Manual - Page 7
the sled yet! Adjustment and alignment are much easier at this point without the lens. 3. Attaching the lens bracket to the adaptor plate Remove the bracket mounting screws from the inside holes in the adaptor plate and use them to attach the lens bracket supplied with the Optoma BX-AL133 anamorphic - Optoma BX-AL133 | User Manual - Page 8
User's Manual BX-AL133 Setup 1. Power up the sled and set LENS IN position Slide the lens into the middle of the sled before powering up. Plug the power adaptor into an AC outlet, then into the back of the unit as illustrated. Using the remote, press the "lens in" button. The lens sled will slowly - Optoma BX-AL133 | User Manual - Page 9
User's Manual BX-AL133 3. Attaching the lens to the bracket Attach the Optoma BX-AL133 anamorphic lens to the bracket using the plastic knobs supplied with the lens. Adjust the anamorphic lens vertically for correct alignment. When the image is correct, tighten the knobs against the bracket. Using - Optoma BX-AL133 | User Manual - Page 10
User's Manual BX-AL133 Remote Control and Motor Operation The LED indicator on the sled will glow when the unit is ON, and flash when any button is pressed. It will also flash when the lens is in motion. The LED will be off in standby mode. Buttons: 8-Button Remote Control OFF - Puts the sled in - Optoma BX-AL133 | User Manual - Page 11
User's Manual BX-AL133 Rear Panel − Triggers and Sensors To use the automatic lens trigger, your projector or scalar must be equipped with a lens trigger and a standard double-ended 3.5 mm (1/8 inch) male mono or stereo jack cable. Simply plug the cable into the projector's lens trigger jack and - Optoma BX-AL133 | User Manual - Page 12
Maintenance The Optoma BX-AL133 anamorphic lens system is maintenance-free. It will deliver many years of trouble-free service as delivered from the factory. To clean: Lightly blow off any surface debris from the lens. If needed, clean the lens using standard cleaning supplies while the projector is - Optoma BX-AL133 | User Manual - Page 13
User's Manual BX-AL133 Specifications Electrical Characteristics Model Optoma BX-AL133 Motorized Sled Power Supply 110/120v, 50-60 Cycles Sensor IR Carrier Frequency 38 kHz Batteries 2 AAA (for Remote) Certification FCC, CE (BX-AL133 Motor Drive Unit) UL Class II (Power Supply Only) - Optoma BX-AL133 | User Manual - Page 14
Dimensions Ø.25" 2.5" 4.511" Score Mark (Motor Side) 7.25" 10.842" 19.675" 7.705" User's Manual BX-AL133 Score Mark (Pulley Side) 5.375" 8.333" 3.0" 3.579" 3.402" 6.921" 5.973" 5.519" 13.738" 5.094" 4.97" .25" 1.079" 1.52" For more information, please visit our website - Optoma BX-AL133 | User Manual - Page 15
User's Manual BX-AL133 Warranty Optoma Technology Inc. warrants this product to be free of defects in original workmanship and material for a period of twenty-four (24) months from the date of purchased. During this period, a defective unit may be repaired or replaced, at the discretion of Optoma - Optoma BX-AL133 | User Manual - Page 16
User's Manual BX-AL133 Addendum: Adapter Plate This attachment plate is designed to be installed onto a ceiling mounted projector. The location or orientation of the ceiling mount does not need to change. Contents 1 Lens Plate 1 (Bag) Projector Attachment Parts 1 Assembly Kit (Includes) 2 Plate - Optoma BX-AL133 | User Manual - Page 17
and tighten. c. Insert the sled safety assemblies through the remaining two holes from bottom up in the order of screw, motorized mount, lens plate, washer, lock washer and nut. Tighten both safety assemblies. d. Refer to the motorized mount user manual for additional instructions at this time. Use - Optoma BX-AL133 | User Manual - Page 18
User's Manual BX-AL133 Addendum: The Finished Product For more information, please visit our website at: http://www.OptomaUSA.com User's Manual | 18 - Optoma BX-AL133 | User Manual - Page 19
#ANADA
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
 |
 |
User’s Manual
BX-AL133 Anamorphic Lens