Optoma GT200 User's Manual

1

1. Do not block any ventilation openings.

To ensure reliable operation of the

projector and to protect from over

heating, it is recommended to install

the projector in a location that does not

block ventilation. As an example, do not

place the projector on a crowded coffee

table, sofa, bed, etc. Do not put the

projector in an enclosure such as a book

case or a cabinet that restricts air flow.

2. Do not use the projector near water or

moisture. To reduce the risk of fire and/

or electric shock, do not expose the

projector to rain or moisture.

3. Do not install near heat sources such as

radiators, heaters, stoves or any other

apparatus such as amplifiers that emits

heat.

4. Do not use the projector in direct

sunlight.

5. Do not use near any appliance

generating a strong magnetic field.

6. Do not use the projector in areas

susceptible to excessive dust and dirt.

7. Turn off the product before cleaning.

8. Ensure that the ambient room

temperature is within 5- 35°C.

9. Relative Humidity is 5 - 35°C, 80%

(Max.), non-condensing.

10. Do not drop, throw or try to bend your

product.

11. May explode if disposed of in fire.

12. Clean only with dry cloth.

13. Only use attachments/accessories

specified by the manufacturer.

14. Do not use the unit if it has been

physically damaged or abused. Physical

damage/abuse would be (but not

limited to):

▀

■

Unit has been dropped.

▀

■

Charger or plug has been damaged.

▀

■

Liquid has been spilled on to the

projector.

▀

■

Projector has been exposed to rain or

moisture.

▀

■

Something has fallen in the projector

or something is loose inside.

Do not attempt to service the unit

yourself. Opening or removing covers

may expose you to dangerous voltages

or other hazards. Please contact your

local reseller or service center before you

send the unit for repair.

15. Do not let objects or liquids enter the

projector. They may touch dangerous

voltage points and short out parts that

could result in fire or electric shock.

16. See projector enclosure for safety related

markings.

17. The unit should only be repaired by

appropriate service personnel.

18. Do not touch the projector for long

periods of time while the projector is in

use.

I

MPORTANT

S

AFETY

I

NSTRUCTIONS

E

YE

S

AFETY

W

ARNINGS

Avoid staring/facing directly into

the projector beam at all times.

Keep your back to the beam as

much as possible.

A stick or laser pointer is

recommended to avoid the need

for the user to enter the beam.

When the projector is used in a

classroom, adequately supervise

students when they are asked to

point out something on the screen.

In order to minimize power, use

room blinds to reduce ambient

light levels.

CLASS 1 LED PRODUCT

This appendix lists the general notices of

your projector.

FCC notice

This device has been tested and found

to comply with the limits for a Class B

digital device pursuant to Part 15 of the

FCC rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This device generates, uses,

and can radiate radio frequency energy

and, if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this device does cause

harmful interference to radio or television

reception, which can be determined by

turning the device off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

device and receiver.

•

Connect the device into an outlet on

a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced

radio/television technician for help.

Notice: Shielded cables

All connections to other computing

devices must be made using shielded

cables to maintain compliance with

FCC regulations.

Caution:

Changes or modifications not

expressly approved by the

manufacturer could void the

user’s authority, which is granted

by the Federal Communications

Commission, to operate this device.

Operation conditions

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

1.

this device may not cause harmful

interference, and

2.

this device must accept any

interference received, including

interference that may cause

undesired operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian

ICES-003.

Remarque à l’intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la

norme NMB-003 du Canada.

Declaration of Conformity for EU countries

• EMC Directive 2004/108/EC (including

amendments)

• Low Voltage Directive 2006/95/EC

• R & TTE Directive 1999/5/EC (if product has

RF function)

R

EGULATION

&

SAFETY

NOTICES

D

ISPOSAL

OF

W

ASTE

E

LECTRICAL

&

E

LECTRONIC

E

QUIPMENT

(Applicable throughout the European

Union and other European countries

with separate collection programs)

This symbol found on your product or on

its packaging, indicates that this product

should not be treated as household

waste when you wish to dispose of it.

Instead, it should be handed over to an

applicable collection point for the recycling

of electrical and electronic equipment.

By ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences to the environment

and human health, which could otherwise

be caused by inappropriate disposal of this

product. The recycling of materials will

help to conserve natural resources.

This symbol is only

valid in the European

Union.

If you wish to discard

this product, please

contact your local

authorities or dealer

and ask for the correct

method of disposal.

Optoma GT200 User's Manual

Optoma GT200 Manual

Optoma GT200 manual content summary: