Optoma HD6800 User Manual
Optoma HD6800 Manual
 |
View all Optoma HD6800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma HD6800 manual content summary:
- Optoma HD6800 | User Manual - Page 1
20 Menu Tree...21 Image ...22 Display ...27 Setup...30 Options...32 Appendices 34 Troubleshooting 34 Image Problems 34 Intermission Problems 37 LED Problems ...37 Remote Control Problems 38 Replacing the Lamp 39 Compatibility Modes 40 Ceiling Mount Installation 41 Optoma Global Office 42 1 - Optoma HD6800 | User Manual - Page 2
amplifiers) that produce heat. 5. Clean only with a dry cloth. 6. Only use attachments/accessories specified by the manufacturer. 7. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way: ▀■ Such as power supply cord or plug is damaged - Optoma HD6800 | User Manual - Page 3
- Please do not open or disassemble the projector as this may cause electric shock. ▀■ Warning- When replacing the lamp, please allow unit to cool down, and follow all replacement instructions. See page 39. ▀■ Warning- This projector will detect the life of the lamp itself. Please be sure to - Optoma HD6800 | User Manual - Page 4
Usage Notice Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don't: Block the ventilation slots and openings on the - Optoma HD6800 | User Manual - Page 5
best way to achieve this is by ceiling-mounting rather than floor or table-mounting the projector. ▀■ When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. ▀■ In order to minimize the lamp power needed, use room blinds to reduce - Optoma HD6800 | User Manual - Page 6
is an WXGA single chip 0.65" DLPTM projector. Outstanding features include: Single 16:9 1280 x 768 Dark Chip2TM DLPTM technology Dual resolution support: -16:10 (1280 x 768) -16:9 (1280 x 720 ) native for 720P HDTV capability Uses 7 segment color wheel GRBWGRB cycle 480i - NTSC/NTSC4.43 - Optoma HD6800 | User Manual - Page 7
Introduction Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. English Projector with lens cap Power Cord 1.8m S-Video Cable 1.8m Composite Video Cable RCA Component Cable 1.8m - Optoma HD6800 | User Manual - Page 8
Introduction Product Overview Main Unit 2 1 7 10 5 3 6 4 5 1 9 7 8 1. Control Panel 2. Zoom Lever 3. Focus Ring 4. Elevator Button (one on each side) 5. Elevator Feet 6. Zoom Lens 7. IR Receivers 8. Connection Ports 9. Power Socket & Main Power Switch 10. Tilt-Adjustment Feet 8 - Optoma HD6800 | User Manual - Page 9
English Introduction Control Panel 98 7 654 321 1. Lamp Indicator LED 2. Temp Indicator LED 3. Standby/On LED 4. Menu (On/Off) 5. Select (Enter) 6. IR Receiver 7. Four Directional Select Keys 8. Re-Sync 9. Source Select 9 - Optoma HD6800 | User Manual - Page 10
2. DVI-I Input Connector (PC Digital and DVI-HDCP) 3. Component Video Input Connector 4. Composite Video Input Connector 5. S-Video Input Connector 6. RS232 Input Connector 7. Service Connector 8. +12V Relay Connector 9. Main Power Switch 10. Power Socket 11. Kensington MicrosaverTM Lock Port 10 - Optoma HD6800 | User Manual - Page 11
English Introduction Remote Control 1 1. Power On/Off 2. Contrast 10 2 3. Image Shift 4. H. Keystone 3 5. V. Keystone 4 6. Select (Enter) 5 7. Four Directional Select Keys 6 8. Display Mode 9. Zoom 7 10. Brightness 11. Menu 11 86 12. Overscan - Optoma HD6800 | User Manual - Page 12
Connecting the Projector SCART DVD Player 7 RGB DVI +12V Relay Output 3 8 9 2 1 Due to the difference in applications for each country, some regions may have different accessories. S-Video Output 4 6 5 Video Output DVD Player, Set-top Box, HDTV receiver 1...Power Cord 2 DVI - Optoma HD6800 | User Manual - Page 13
. Ensure that the button on the back of the projector is turned on. The Power LED will flash green. 3. Turn on the lamp by pressing "Standby/On" button either on the top of the projector or on the remote. The Power LED will turn green. The startup screen will display in approximately 30 seconds - Optoma HD6800 | User Manual - Page 14
the electrical outlet and the projector. 4. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the "LAMP" indicator lights solid red, the projector will automatically shut itself down. Please contact your local reseller or service center. See page 42 - Optoma HD6800 | User Manual - Page 15
English Installation Adjusting the Projected Image Adjusting the Projector's Height The projector is equipped with elevator feet for adjusting the image height. To raise the image: 1. Press the elevator button . 2. Raise the image to the desired height - Optoma HD6800 | User Manual - Page 16
in or zoom out. To focus the image, turn the focus ring until you see a clear image. The projector will focus at distances from 4.9 to 39.4 feet (1.5 to 12 H' (1280X768) H 16 B(1280X768) LA D W (1280X768) 0 (1280X768) Throw Ratio (TR)=1.96 as Wide mode A=6.52° B (1280x768)=25.54° W0 ( - Optoma HD6800 | User Manual - Page 17
User Controls Control Panel & Remote Control There are two ways for you to control the functions: Control Panel and Remote Control. Control Panel Remote Control English Using the Control Panel Source Confirm your item selection. Automatically synchronizes the projector to the input source. 17 - Optoma HD6800 | User Manual - Page 18
User Controls Using the Remote Control Power Refer to the "Power On/Off the Projector" section on pages 13-14. Brightness Adjust the brightness of the image. Contrast Control the degree of difference between the lightest and darkest parts of the picture. Image Shift Shifts the projected - Optoma HD6800 | User Manual - Page 19
English User Controls DVI-D DVI-A HDMI YPbPr Video S-Video Press "DVI-D" to choose Digital Signal source from DVI-I connector. Press "DVI-A" to choose Analog Signal source from - Optoma HD6800 | User Manual - Page 20
User Controls On-screen Display Menus The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or - Optoma HD6800 | User Manual - Page 21
Menu Tree User Controls English 21 - Optoma HD6800 | User Manual - Page 22
optimized for various types of images. Cinema: For home theater. Bright TV sRGB: For standard color. User: Memorize user's settings. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of - Optoma HD6800 | User Manual - Page 23
English User Controls Tint Adjusts the color balance of red and green. Press the Press the Sharpness to increase the amount of green in the image. to increase the amount of red - Optoma HD6800 | User Manual - Page 24
User Controls Image | Advance Degamma This allows you to choose a degamma table that has been finetuned to bring out the best image quality for the input. Film: For home theater. Video: For video or TV source. Graphics: For image source. PC: For PC or computer source. Brilliant Color This - Optoma HD6800 | User Manual - Page 25
English User Controls On: The dynamic image performance manager is active in making sure your greatest pleasure from seeing a movie dynamically with the most dark details revealed, - Optoma HD6800 | User Manual - Page 26
User Controls Input Source Enable input sources. Press or into the next menu as below and then use or to select. Press "Select (Enter)" to finalize the selection. The projector will not search inputs that are deselected. Color Space Select an appropriate color matrix type from RGB or YPbPr. 26 - Optoma HD6800 | User Manual - Page 27
Widescreen TV. Native: This format displays the original image without any scal- ing. LBX: This format is for non-16x9, letterbox source and for users who use external 16x9 lens to display 2.35:1 aspect ratio using full resolution. Input Signal Display area Picture area Display on Screen 27 - Optoma HD6800 | User Manual - Page 28
User Controls Detail informations about LBX mode : 1. Some Letter-Box DVD contents are DVD and HDTV film source) that support anamorphic wide is enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars, the full lamp power and vertical resolution is fully utilized for - Optoma HD6800 | User Manual - Page 29
400/854 x 480 1280 x 720/1280 x 768/1920 x 1080. Normal: If your PC output is a Normal (4:3) resolution you must select this setting. Examples of Normal resolutions are: 640 x 480/800 x 600/1024 x 768/1152 x 870 (* for MAC)/1280 x 1024/1400 x 1050. *All supported resolutions are listed on page 40 - Optoma HD6800 | User Manual - Page 30
default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection. Rear-Ceiling When - Optoma HD6800 | User Manual - Page 31
English User Controls Tracking : Synchronizes the signal timing of the display with the graphics card. If you experience an unstable or flickering image, use this function to correct it. H. Position: Adjusts the horizontal position. V. Position: Adjusts the vertical position. 31 - Optoma HD6800 | User Manual - Page 32
search for a specified connection port. High Altitude Choose "On" to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Auto Power Off (min) Sets the interval of power-off of the system, if there is no signal input. (In - Optoma HD6800 | User Manual - Page 33
English User Controls Options | Lamp settings Lamp Hour Displays the cumulative lamp operating time. Lamp Reminding Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear up 30 hours before suggested replacement of lamp. - Optoma HD6800 | User Manual - Page 34
Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. (See page 42 for details) Image Problems No image appears on-screen Ensure all the cables and power - Optoma HD6800 | User Manual - Page 35
computer's manual for detailed information. Unstable or flickering image Use "Tracking" to correct it. See page 31 for more information. Change the monitor color setting on your computer. (*) The resolution: Image has vertical flickering bar WXGA (1280 x 768) is recommended for this projector - Optoma HD6800 | User Manual - Page 36
on the projector lens. Make sure the projection screen is between the required distance 4.9 to 39.4 feet (1.5 to 12.0 meters) from the projector. See ] button on the remote control or [Projector menu] on the projector panel, go to "Display-->Format". Try the different settings. Use of Keystone - Optoma HD6800 | User Manual - Page 37
loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on page 39. LED Problems LED lighting message Message Standby State (Input power cord) Standby/On LED (Green - Optoma HD6800 | User Manual - Page 38
Appendices Thermal Warning: Replacing the lamp: Remote Control Problems If the remote control does not work Check the operating angle for the remote control is approximately ±22.5°. Make sure there are not any obstructions between the remote con- trol and the projector. Move to within 6 m ( - Optoma HD6800 | User Manual - Page 39
the lamp module. 7. Pull out the lamp module. To replace the lamp module, reverse the previous steps. 8. Turn on the projector and do "Lamp Reset" after the lamp module is replaced. Lamp Reset: (i)Press "Menu" -> (ii)Select "Options" -> (iii)Select "Lamp settings" ->(iv)Select "Lamp reset - Optoma HD6800 | User Manual - Page 40
Compatibility Modes Mode VESA VGA VESA VGA VESA VGA VESA SVGA VESA XGA VESA WXGA HD * HD * SXGA * SXGA+ * MAC MAC G4 i MAC DV Resolution 640 x 480 848 x 480 720 x 400 800 x 600 1024 x 768 1280 x 768 1280 x 720 1920 x 1080 1280 x 1024 1400 x 1050 1152 x 870 640 x 480 1024 x 768 V.Frequency (Hz) 60 - Optoma HD6800 | User Manual - Page 41
buy the ceiling mount from other company, please ensure that there is at least 10cm distance between the bottom cover of the projector and the ceiling. 2. Avoid placing the projector near sources of heat such air-conditioning units and heaters otherwise it may overheat and shut down automatically - Optoma HD6800 | User Manual - Page 42
Global Office For service or support please contact your local office. USA 715 Sycamore Drive Milpitas, CA 95035, USA www.optomausa.com Tel : 408-383-3700 Fax: 408-383-3702 Service : [email protected] Canada 120 West Beaver Creek Road Unit #9 Richmond Hill, ON L4B 1L2, Canada Tel : 905-882
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
 |
 |
Table of contents
English
1
Table of Contents
...................................................................................
1
Usage Notice
..........................................................................................
2
Safety Information
.........................................................................................
2
Precautions
...................................................................................................
3
Eye Safety Warnings
.....................................................................................
5
Introduction
............................................................................................
6
Product Features
...........................................................................................
6
Package Overview
........................................................................................
7
Product Overview
..........................................................................................
8
Main Unit
................................................................................................................
8
Control Panel
.........................................................................................................
9
Connection Ports
.................................................................................................
10
Remote Control
....................................................................................................
11
Installation
............................................................................................
12
Connecting the Projector
.............................................................................
12
Powering On/Off the Projector
....................................................................
13
Powering On the Projector
...................................................................................
13
Powering Off the projector
...................................................................................
14
Warning Indicator
.................................................................................................
14
Adjusting the Projected Image
....................................................................
15
Adjusting the Projector’s Height
...........................................................................
15
Adjusting the Projector’s Zoom / Focus
...............................................................
16
Adjusting Projected Image Size
...........................................................................
16
User Controls
.......................................................................................
17
Control Panel & Remote Control
.................................................................
17
On-screen Display Menus
...........................................................................
20
How to operate
....................................................................................................
20
Menu Tree
............................................................................................................
21
Image
...................................................................................................................
22
Display
................................................................................................................
27
Setup
....................................................................................................................
30
Options
.................................................................................................................
32
Appendices
..........................................................................................
34
Troubleshooting
...........................................................................................
34
Image Problems
..................................................................................................
34
Intermission Problems
........................................................................................
37
LED Problems
.....................................................................................................
37
Remote Control Problems
...................................................................................
38
Replacing the Lamp
....................................................................................
39
Compatibility Modes
....................................................................................
40
Ceiling Mount Installation
............................................................................
41
Optoma Global Office
..................................................................................
42