Optoma TW695UTi-3D User's Manual
Optoma TW695UTi-3D Manual
 |
View all Optoma TW695UTi-3D manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma TW695UTi-3D manual content summary:
- Optoma TW695UTi-3D | User's Manual - Page 1
Pen 11 Installation 12 Connecting the Projector 12 Removing and Attaching the Cable 27 IMAGE 30 IMAGE | Advanced 32 DISPLAY 34 DISPLAY | 3D 37 SETUP 38 SETUP | Signal (RGB 41 SETUP | Security How to use the Optoma Presenter .... 66 Appendices 70 Troubleshooting 70 Replacing the lamp - Optoma TW695UTi-3D | User's Manual - Page 2
(servicing) instructions in service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. 7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short - Optoma TW695UTi-3D | User's Manual - Page 3
in this user's guide. ▀■ Warning- Do not look into the projector's lens when the cool down. Follow instructions as described on pages 76-77. ▀■ Warning- This projector will detect the life on the screen. Please contact your local reseller or service center to change the lamp as soon under "Replacing - Optoma TW695UTi-3D | User's Manual - Page 4
Usage Notice Do: Turn off and unplug the power plug from the AC outlet before cleaning the product. Use a soft dry cloth with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Do not: Block the - Optoma TW695UTi-3D | User's Manual - Page 5
your back to the beam as much as possible. ▀■ When projector is used in a classroom, adequately supervise students when they are resolution ▀■ HD compatible - 1080p supported ▀■ VGA monitor loop through (works on standby mode > 1W) ▀■ BrilliantColorTM Technology ▀■ Security Bar and Kensington Lock - Optoma TW695UTi-3D | User's Manual - Page 6
, please contact your nearest customer service center. Projector with lens cap Power Cord 1.8m VGA Cable 1.8m Due to different applications in each country, some regions may have different accessories. 2 × AAA Batteries Documentation : User's Manual - Optoma TW695UTi-3D | User's Manual - Page 7
S-VIDEO VGA1-IN / SCART / YPbPr 12V OUT L R AUDIO OUT MIC AUDIO2-IN (S-VIDEO/VIDEO) VGA2-IN / YPbPr VGA-OUT HDMI PB/MOUSE SERVICE RJ-45 USB / DISPLAY 9 8 10 4 5 15 5 2 13 14 1. Control Panel 2. IR Receivers 3. Cable Cover 4. Speaker 5. Tilt-Adjustment Feet 6. Mirror Cover 7. Input - Optoma TW695UTi-3D | User's Manual - Page 8
Introduction Control Panel 1 2 3 4 5 6 7 89 10 1. Lamp LED 2. Temp LED 3. Source 4. Re-Sync 5. Help 6. Power/Standby button and LED 7. Enter 8. Keystone Correction 9. Four Directional Select Keys 10. Menu English 8 - Optoma TW695UTi-3D | User's Manual - Page 9
/ YPbPr 12V OUT L R AUDIO OUT MIC AUDIO2-IN (S-VIDEO/VIDEO) VGA2-IN / YPbPr 14 VGA-OUT HDMI PB/MOUSE SERVICE RJ-45 15 USB / 16 DISPLAY 17 Monitor loop through only support in VGA1-In/ SCART/YPbPr. 1. 12V Trigger Relay (12V, 250mA) 2. 3.5mm Mini Jack Audio1 Input for VGA1/VGA2 - Optoma TW695UTi-3D | User's Manual - Page 10
21 22 23 1. LED Indicator 2. Power On/Off 3. Four Directional Select Keys 24 4. Mouse Right Click 5. Page Up 6. Re-Sync 7. Page Down 3 8. Volume +/- 4 9. 3D 10. AV mute 5 11. Video 6 12. PC/Mouse control 7 13. Mouse Left Click 14. Enter/Help 8 15. Source 9 16. Keystone +/17. Menu 10 - Optoma TW695UTi-3D | User's Manual - Page 11
Introduction Interactive Pen 1 3 2 4 5 6 The interactive pen is optional accessory. 1. Battery Cover 2. Mouse Right Click 3. Menu 4. Mouse Left Click 7 8 5. Lens 6. Nib 7. Power On/Off 8. LED Indicators 1 Warning: • Danger of explosion if battery is incorrectly replaced. • Replace only - Optoma TW695UTi-3D | User's Manual - Page 12
Installation Connecting the Projector Removing and Attaching the Cable Cover Cable Cover 2 1 Procedure for Removing and Attaching the Cable Cover: 1. Unscrew the screw on the cable cover. 1 2. Lift up and remove the cable cover. 2 Install the cable cover by reversing the previous steps. English 12 - Optoma TW695UTi-3D | User's Manual - Page 13
S-VIDEO VGA1-IN / SCART / YPbPr 12V OUT L R AUDIO OUT MIC AUDIO2-IN (S-VIDEO/VIDEO) VGA2-IN / YPbPr VGA-OUT HDMI PB/MOUSE SERVICE RJ-45 USB / DISPLAY R E62405SP 8 9 1...Power Cord 2 Audio Output Cable 3 Audio Input Cable 4 RS232 Cable 5...VGA Cable 6 HDMI Cable 7...*USB Cable - Optoma TW695UTi-3D | User's Manual - Page 14
232 VIDEO S-VIDEO VGA1-IN / SCART / YPbPr 12V OUT L R AUDIO OUT MIC AUDIO2-IN (S-VIDEO/VIDEO) VGA2-IN / YPbPr VGA-OUT HDMI PB/MOUSE SERVICE RJ-45 USB / DISPLAY 9 R E62405SP 10 DVD Player, Set-top Box, HDTV receiver Due to the difference in applications for each country, some - Optoma TW695UTi-3D | User's Manual - Page 15
Turn on the lamp by pressing " " button either on the top of the projector or on the remote. The POWER/STANDBY LED will now turn Green. When to display on the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push menu button and go to - Optoma TW695UTi-3D | User's Manual - Page 16
When the warning indicators (see below) come on, the projector will automatically shutdown: Contact the nearest service center if the "LAMP" LED indicator is lit red and if "POWER/STANDBY" indicator flashes amber. projector displays these symptoms. See pages 87-88 for more information - Optoma TW695UTi-3D | User's Manual - Page 17
for adjusting the image height. 1. Locate the adjustable foot you wish to modify on the underside of the projector. 2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the remaining feet as needed. Tilt-Adjustment Feet Tilt-Adjustment Ring - Optoma TW695UTi-3D | User's Manual - Page 18
's Focus To focus the image, rotate the focus ring until the image is clear. XGA series: The projector will focus at distances from 1.58 to 2.17 feet (475 to 662 mm). WXGA series: The projector will focus at distances from 1.58 to 2.17 feet (495 to 661 mm). Focus Ring Adjusting Projection - Optoma TW695UTi-3D | User's Manual - Page 19
and screen center (H) C,E=>T hrow distance D=>V ertical distance between lens center and bottom of screen (top of screen for ceiling mount) α=>Throw angle (B) (D) Throw Angle (α) Lens Center (C) (E) XGA Screen Size Diagonal Width (W) inch mm inch mm 63 1600 50 1280 65 1651 52 - Optoma TW695UTi-3D | User's Manual - Page 20
Control Control Panel Using the Control Panel Power/ Standby button and LED Refer to the "Power On/Off the Projector" section on pages 15-16. Indicate the projector's status. RE-SYNC Enter SOURCE Menu Four Directional Select Keys Keystone HELP Lamp LED Temp LED Automatically synchronize the - Optoma TW695UTi-3D | User's Manual - Page 21
or make adjustments to your selection. Adjust image distortion caused by tilting the projector. Volume +/- Adjust to increase / decrease the volume. Brightness Adjust the brightness of the image. 3D Menu HDMI Press the "3D" to turn the 3D OSD menu on/off. Press "Menu" to launch the on-screen - Optoma TW695UTi-3D | User's Manual - Page 22
User Controls Using the Remote Control AV mute Momentarily turns off/on the audio and video. S-Video Press "S-Video" to choose S-Video source. VGA Press "VGA" to choose VGA sources. Video Press "Video" to choose Composite video source. Interactive Pen Using the Interactive Pen ON/OFF - Optoma TW695UTi-3D | User's Manual - Page 23
User Controls Using the HELP button The HELP function ensures easy setup and operation. Press the "?" button on the remote control or press the "HELP" button on the control panel to open the Help Menu. 23 English - Optoma TW695UTi-3D | User's Manual - Page 24
User Controls Help menu button functions only when no input source is detected. Please refer to the "Troubleshooting" section on pages 70-75 for more details. If input source is detected and help button is pressed, the following pages will appear to help diagnose any problems. English 24 - Optoma TW695UTi-3D | User's Manual - Page 25
User Controls 25 English - Optoma TW695UTi-3D | User's Manual - Page 26
you to make image adjustments and change a variety of settings. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or Projector Keypad. 2 When OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press or "Enter - Optoma TW695UTi-3D | User's Manual - Page 27
Timer Change Password Exit Settings Presentation / Bright / Movie / sRGB / Blackboard / Classroom / User / 3D -50~50 -50~50 1~15 -50~50 LBX / Native / AUTO 0~10 -5~25 (80%~200%) -50~50 -50~50 -40~40 Off / DLP-Link / IR On / Off English / Deutsch / Français / Italiano / Español / Português / - Optoma TW695UTi-3D | User's Manual - Page 28
Controls Main Menu Setup Options Sub Menu Projector ID Mute Volume Audio Input Advanced Set function Reset Channel Information Exit Settings 0~99 On / Off 0~10 #6 Default / Audio1(Phone jack) / Audio2 (RCA R/L) Optoma / Neutral / User Off / CC1 / CC2 Yes / No On / Off On / Off On / Off On / Off - Optoma TW695UTi-3D | User's Manual - Page 29
to the signal type selected and the projector model you are using. (#1) "Color" and "Tint" are only supported in Video mode. (#2) For XGA on "Screen Type" setting. (#4) "3D Sync Invert" is only available when 3D is enabled. (#5) "Signal" is only supported in Analog VGA (RGB) signal. (#6) - Optoma TW695UTi-3D | User's Manual - Page 30
from PC input. Bright: Maximum brightness from PC input. Movie: For home theater. sRGB: Standardised accurate color. Blackboard: classroom. User: User's settings. 3D: Recommand setting for 3D mode enabled. Any further ad- justments by the user in 3D will be saved in this mode for - Optoma TW695UTi-3D | User's Manual - Page 31
User Controls "Color" and "Tint" functions are only supported under Video mode. Sharpness Adjust the sharpness of the image. Press the to decrease the sharpness. Press the to increase the sharpness. Color Adjust a video - Optoma TW695UTi-3D | User's Manual - Page 32
table that has been fine-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source. PC: for PC or computer source. BrilliantColor™ This adjustable item utilizes a new color-processing algorithm and system level - Optoma TW695UTi-3D | User's Manual - Page 33
which sources you require. Press "Enter" to finalize the selection. The projector will not search for inputs that are not selected. Image AI Image AI manager is active in making sure your greatest pleasure from seeing a movie dynamically with the most dark details revealed, vivid and bright image - Optoma TW695UTi-3D | User's Manual - Page 34
16×9 input sources, like HDTV and DVD enhanced for Wide screen TV. (576i/p) 16:9-II: This format is for 16×9 input sources, like HDTV and DVD enhanced for Wide screen TV. (480i/p) Native: This format displays the original image without any scaling - Optoma TW695UTi-3D | User's Manual - Page 35
" setting. WXGA 4:3: This format is for 4×3 input sources. 16:9: This format is for 16×9 input sources, like HDTV and DVD enhanced for Wide screen TV. 16:10: This format is for 16×10 input sources, like widescreen laptops. LBX: This format is for non-16x9, letterbox source and for users - Optoma TW695UTi-3D | User's Manual - Page 36
User Controls Each I/O has different setting of "Edge mask". "Edge mask" and "Zoom" can't work at same time. Edge Mask Edge mask function removes the noise in a video image. Edge mask the image to remove video encoding noise on the edge of video source. Zoom Press the to reduce the size of - Optoma TW695UTi-3D | User's Manual - Page 37
when 3D is enabled and this mode 3D is for DLP link glass only. Compatible 3D source, 3D content and active shutter glasses are required for 3D viewing. 3D O ff: Select "Off" to turn 3D settings off for 3D images. D LP Link: Select "DLP Link" to use optimized settings for DLP Link 3D images - Optoma TW695UTi-3D | User's Manual - Page 38
User Controls SETUP Language Choose the multilingual OSD menu. Press or into the sub menu and then use the or key to select your preferred language. Press "Enter" to finalize the selection. "Screen Type" is for WXGA only. Screen Type Choose the screen type from16:10 or 16:9. Projection Rear- - Optoma TW695UTi-3D | User's Manual - Page 39
appear reversed in upside down position. Menu Location Choose the menu location on the display screen. Projector ID ID definition can be set up by menu (range 0~99), and allow user control an individual projector by RS232. Refer to page 81~85 for the complete list of RS232 commands. Mute Choose - Optoma TW695UTi-3D | User's Manual - Page 40
Press the to decrease the volume. Press the to increase the volume. Audio Input The default audio settings are on the back panel of the projector. Use this option to reassign any of the Audio Inputs (1 or 2) to the current image source. Each Audio input can be assigned to more than - Optoma TW695UTi-3D | User's Manual - Page 41
, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. Phase Synchronize the signal timing of the display with the graphic card. If the image - Optoma TW695UTi-3D | User's Manual - Page 42
default value is "1234" (first time). Security On: Choose "On" to use security verification when the turning on the projector. Off: Choose "Off" to be able to switch on the projector without password verification. Security Timer Use this function to set the how long (Month/Day/Hour) the - Optoma TW695UTi-3D | User's Manual - Page 43
User Controls If the incorrect password is entered 3 times, the projector will automatically shut down. If you have forgotten your password, please contact your local office for support. 43 English - Optoma TW695UTi-3D | User's Manual - Page 44
projector is powered on. Optoma : The default startup screen. Neutral: Logo is not displayed on startup screen. User: Use stored picture from "Logo Capture" function. For successful logo capture, please ensure that the onscreen image does not exceed the projector time the projector is - Optoma TW695UTi-3D | User's Manual - Page 45
the OSD menu, the new setting will take effect on next open. On: Assign an IP address to the projector from an external DHCP server automatically. Off: Assign an IP address manually. IP Address Select an IP address. Subnet Mask Select subnet mask number. Gateway Select the default gateway of the - Optoma TW695UTi-3D | User's Manual - Page 46
to use web browser to control your projector 1. Turn on DHCP to allow the DHCP server to automatically assign an IP, or manually enter the required network information. 4. Based 15 15 (N/A) 15 15 When you used the projector IP address, you will can not link to your service server. English 46 - Optoma TW695UTi-3D | User's Manual - Page 47
User Controls When making a direct connection from your computer to the projector Step 1: Find an IP Address (192.168.0.100) from LAN function of projector. Step 2: Select apply and press "Enter" button to submit function or press "menu" key to exit. Step 3: To open Network Connections, click Start - Optoma TW695UTi-3D | User's Manual - Page 48
on the combination of IP ID and IP address). Crestron RoomView monitors each projector, including projector's online status, system power, lamp life, network setting and hardware faults, image) 1. Main Screen 2. Edit Room Crestron RoomView function support is dependent on models. English 48 - Optoma TW695UTi-3D | User's Manual - Page 49
3. Edit Attribute User Controls 4. Edit Event For more information, please visit http://www.crestron.com & www.crestron.com/getroomview. 49 English - Optoma TW695UTi-3D | User's Manual - Page 50
Off: Choose "Off" to show the "searching" message. Keypad Lock When the keypad lock function is "On", the control panel will be locked however, the projector can be operated by the remote control. By selecting "Off", you will be able to reuse the control panel. Background Color Use this feature to - Optoma TW695UTi-3D | User's Manual - Page 51
User Controls Optional Filter Installed Select "Yes" to display warning message after 500 hours of use. Select "No" to turn off warning message. Reset Filter Warning Select "Yes" to reset the dust filter hour counter after replacing or cleaning the dust filter. Reset Choose "Yes" to return the - Optoma TW695UTi-3D | User's Manual - Page 52
Power Off (min) Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes). Sleep Timer (min) Sets the countdown timer interval. The countdown timer - Optoma TW695UTi-3D | User's Manual - Page 53
hours before suggested replacement of lamp. When ambient temperature is over 35°C in operating, the projector will switch to STD automatically. Brightness Mode STD: Choose "STD" to dim the projector lamp which will lower power consumption and extend the lamp life. BRIGHT: Choose "BRIGHT" to - Optoma TW695UTi-3D | User's Manual - Page 54
in the following input modes: VGA and HDMI from a PC, and Wireless Display, USB Display, and LAN Display Interactive Pen is supported in 3D source of 120Hz DLP-Link. The response time lag of Dual Pen operation is 180ms. Interactive Choose "On" to enable Interactive and activate the Interactive - Optoma TW695UTi-3D | User's Manual - Page 55
ouble Click: Choose the function as double-clicking. D isable: Disable the Function button. Channel A uto: Channel is selected automatically. M anual: Channel is selected manually. A total of 15 channels are available. Information View the information about the interactive pen. 55 English - Optoma TW695UTi-3D | User's Manual - Page 56
on network protocol, user can configure the projector remotely. It supports to connect the PC with Projector by USB, Ethernet, and Wireless. This • Card Reader • Optoma Presenter How to use Web Control The Web Control application allows user to configure the projector remotely base on various - Optoma TW695UTi-3D | User's Manual - Page 57
• C lick "Download", it displays the interface to download the software of "Optoma Presenter". • Click "Crestron", to enter the control page of Flash UI. • a new password. Projector Control All items in this page is the detail options about how to control the projector more smoothly. Example: - Optoma TW695UTi-3D | User's Manual - Page 58
User Controls Alert Setup This page is to set up the alert notification for kinds of error types by sending mail. Alert type is multi-options. SMTP Mail Setup This page is to set up the details of mail sending, ex. mail server IP address, user name, password and mail address of receivers. (Note: - Optoma TW695UTi-3D | User's Manual - Page 59
User Controls • IP Setup: Click "Obtain an IP address automatically" as auto mode; click "Use the following IP Address" as static mode, IP Address/Subnet Mask/Default Gateway/ DNS Server are required to be filled and then click "Apply" button. • DHCP Server Setup: Enable/Disable, Start IP, End IP, - Optoma TW695UTi-3D | User's Manual - Page 60
This is the control page of Flash UI. Click "Power" to control power on/off of projector. Click "Vol-, Mute, Vol+" to control volume. In the SourceList, it includes all sources that the projector can process. Click "Menu" to open menu; click "Source" to choose next source; click "Auto" to - Optoma TW695UTi-3D | User's Manual - Page 61
Click "Tools", the following items are included: • Crestron Control: the basic network information of the control system device. • Projector: the ID of each projector in a building for Administrator to control. • User Password: change user's password. • Default Language: set the default language - Optoma TW695UTi-3D | User's Manual - Page 62
Default Click "Apply" to reset system to the default settings. Click "Flash Upgrade" to upgrade the Firmware from USB disk, which has been inserted in projector. Reboot System Click "Reboot" to reboot system. English 62 - Optoma TW695UTi-3D | User's Manual - Page 63
display packaged images in a USB flash device. 1. Plugging the USB device into USB port of projector, source of Flash Drive is detected, and then USB Flash Devices Detection Screen is displayed. It supports 3 USB devices at the same time. 2. Press "Enter" to enter Thumbnail mode, different photos in - Optoma TW695UTi-3D | User's Manual - Page 64
3. In the menu of Thumbnail mode, choose Display function, or choose file and press "Enter" to enter Display mode. The following buttons are supported in the user interface: • Display: Enter the Image Display Mode. • Thumbnail: Enter the Thumbnail Display Mode. • Slide Show: Enter the Slide Show - Optoma TW695UTi-3D | User's Manual - Page 65
3/4/5: Slide Show delay in seconds. • S lide Effect: Following modes are supported. (Slide Right/Slide Down/Slide Up/Slide Auto) • Repeat ON/OFF: the image can NOT be displayed due to memory limitation or can NOT support image format, the specific image is displayed on the center of the screen - Optoma TW695UTi-3D | User's Manual - Page 66
be downloaded from web page. Before using this function, a USB cable is needed to connect the Projector and PC Host directly. When the connection is OK, the PC will show a USB device disk. Select "Optoma Presenter", and then run "autorun.exe" to start USB Display. 1. Press the Autorun icon in the - Optoma TW695UTi-3D | User's Manual - Page 67
" button to search the projectors on network and select projectors to connect. 2. Input "User type" and "Password" in log-in interface. Display port can be selected, default is "Full screen". 3. After log-in, Optoma Presenter will modify PC resolution to Ruby supported resolution, and the buttons - Optoma TW695UTi-3D | User's Manual - Page 68
message popup. • Advanced Setting: select JPEG image quality, YUV sample format and network port. Click the button to control all the users and all the projectors connected to the same - Optoma TW695UTi-3D | User's Manual - Page 69
User Controls • : For Administrator user login. • : For Normal user login. • : Status of the connection for connected • : Status of the connection for not connected. • : For the status and display position of local screen on the network display, change it by clicking on it and a dialog box - Optoma TW695UTi-3D | User's Manual - Page 70
Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. No image appears on-screen Ensure all the cables and power connections are correctly and securely - Optoma TW695UTi-3D | User's Manual - Page 71
keys listed below for your notebook manufacturer to send signal out from notebook to projector. Example: [Fn]+[F4] Acer [Fn]+[F5] Asus [Fn]+[F8 Each has a different way to be reactivated. Refer to your computer's manual for detailed information. Image is unstable or flickering Use "Phase" - Optoma TW695UTi-3D | User's Manual - Page 72
DVD title When you play anamorphic DVD or 16:9 DVD, the projector will show the best image when the projector display mode is set to 16:9 in the OSD. If you play 4:3 format DVD titles, please change the format to 4:3 in the projector OSD. If the image is still stretched, you will also need to - Optoma TW695UTi-3D | User's Manual - Page 73
makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on - Optoma TW695UTi-3D | User's Manual - Page 74
±15° both horizontally and vertically of one of the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0°) of the projector. Make sure the batteries are inserted correctly. Replace batteries if they are - Optoma TW695UTi-3D | User's Manual - Page 75
sure the batteries are inserted correctly. Replace batteries if they are exhausted. Make sure there are not any obstructions between the Interactive pen and the projector. Move to within 10m (0°) / 8m (20°) / 5m (45°) of the - Optoma TW695UTi-3D | User's Manual - Page 76
please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at wear safety glasses if changing the bulb when ceiling mounted. "Caution must be used to prevent any loose parts from falling out of projector." Warning - Optoma TW695UTi-3D | User's Manual - Page 77
Appendices The screws on the 1 lamp cover and the 2 3 lamp cannot be removed. 4 The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the - Optoma TW695UTi-3D | User's Manual - Page 78
filter slowly and carefully. 4 7. Clean or replace the dust filter. 5 To install the dust filter, reverse the previous steps. 8. Turn on the projector and use "Reset Dust Filter" after the dust filter is replaced. Filter Reset: (i) Press "Menu" (ii) Select "OPTIONS" (iii) Select "Reset Dust - Optoma TW695UTi-3D | User's Manual - Page 79
120 120 120Hz input signals may be 832 × 624 75 75 dependent on XGA 1024 × 768 60 60 graphics cards XGA 1024 × 768 70 70 support. Please note that XGA 1024 × 768 75 75 using resolutions XGA 1024 × 768 120 120 other than native 1152 × 870 75 75 1024 x 768 (XGA - Optoma TW695UTi-3D | User's Manual - Page 80
Appendices Computer Compatibility Mode MAC LC 13" MAC II 13" MAC 16" MAC 19" MAC MAC G4 i MAC DV i MAC DV Resolution 640 × 480 640 × 480 832 × 624 1024 × 768 1152 × 870 640 × 480 1024 × 768 1152 × 870 V-Sync (Hz) 66.66 66.68 74.55 75 75.06 60 75 75 H-Sync (KHz) 34.98 35.00 49.73 60.24 68.68 - Optoma TW695UTi-3D | User's Manual - Page 81
Appendices RS232 Commands and Protocol Function List RS232 Pin Assignments RS232 shell is grounded. 1 2 3 Pin no. 1 2 3 Spec. (from projector side) TXD RXD GND 81 English - Optoma TW695UTi-3D | User's Manual - Page 82
Projector Return (Fail): F Projector Return (Pass): P Projector Return (Fail): F XX=01ˀ99, projector's ID, XX=00 is for all projectors SEND to projector 30 32 30 20 33 0D Movie ~XX20 4 7E 30 30 32 Classroom ~XX20 9 7E 30 30 32 30 20 39 0D 3D ~XX21 n 7E 30 30 32 31 20 a 0D Brightness - Optoma TW695UTi-3D | User's Manual - Page 83
33 30 20 31 0D 3D Mode On ~XX230 0 7E 30 30 32 33 30 20 30 0D 3D Mode Off ~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert On ~XX231 37 38 20 32 0D Off (0/2 for backward compatible) ~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39) ~XX80 1 7E 30 30 38 30 20 - Optoma TW695UTi-3D | User's Manual - Page 84
Appendices ~XX81 n 7E 30 30 38 31 20 a 0D Volume n = 0 (a=30) ~ 20 (a=32 30) ~XX82 1 7E 30 30 38 32 20 31 0D Logo Optoma ~XX82 2 7E 30 30 38 32 20 32 0D User ~XX83 1 7E 30 30 38 33 20 31 0D Logo Capture ~XX88 0 7E 30 30 - Optoma TW695UTi-3D | User's Manual - Page 85
Lamp Hours Running Out READ from projector 232 ASCII Code HEX Code Function Projector Return Description ~XX121 1 7E 20 31 0D Display Mode OKn n : 0/1/2/3/4/5/6/7/8 = None/Presentation/Bright/Movie/sRGB/ User/Blackboard/Classroom/3D ~XX124 1 7E 30 30 31 32 34 20 31 0D Power - Optoma TW695UTi-3D | User's Manual - Page 86
Appendices Wall Mount Installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: Please note that damage - Optoma TW695UTi-3D | User's Manual - Page 87
service or support please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com 888-289-6786 510-897-8601 [email protected] Canada 2420 Meadowpine Blvd., Suite #105 Mississauga, ON, L5N 6S2, Canada www.optoma.ca 888-289-6786 510-897-8601 services@optoma - Optoma TW695UTi-3D | User's Manual - Page 88
Latin America 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com +31 (0) 36 820 0253 +31 (0) 36 548 9052 www.optoma.nl 888-289-6786 510-897-8601 [email protected] Korea WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, seoul,135-815, KOREA +82+2+34430004 +82+2+34430005 Japan - Optoma TW695UTi-3D | User's Manual - Page 89
& Safety Notices This appendix lists the general notices of your projector. FCC notice This device has been tested and found to radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no - Optoma TW695UTi-3D | User's Manual - Page 90
/108/EC (including amendments) • Low Voltage Directive 2006/95/EC • R & TTE Directive 1999/5/EC (if product has RF function) Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
 |
 |
1
English
Table of Contents
............................
1
Usage Notice
...................................
2
Safety Information
...............................
2
Precautions
.........................................
3
Eye Safety Warnings
..........................
5
Product Features
................................
5
Introduction
......................................
6
Package Overview
..............................
6
Product Overview
...............................
7
Main Unit
..............................................
7
Control Panel
.......................................
8
Input/Output Connections
....................
9
Remote Control
..................................
10
Interactive Pen
...................................
11
Installation
.....................................
12
Connecting the Projector
..................
12
Removing and Attaching the Cable
Cover
.................................................
12
Connect to Computer/Notebook
........
13
Connect to Video Sources
.................
14
Powering the projector On / Off
........
15
Powering On the Projector
.................
15
Powering Off the Projector
.................
16
Warning Indicator
...............................
16
Adjusting the Projected Image
..........
17
Adjusting the Projector’s Height
........
17
Adjusting the Projector’s Focus
.........
18
Adjusting Projection Image Size
........
18
User Controls
................................
20
Control Panel & Remote Control
......
20
Control Panel
.....................................
20
Remote Control
..................................
21
Interactive Pen
...................................
22
On-screen Display Menus
................
26
How to operate
.................................
26
Menu Tree
..........................................
27
IMAGE
...............................................
30
IMAGE | Advanced
............................
32
DISPLAY
............................................
34
DISPLAY | 3D
...................................
37
SETUP
...............................................
38
SETUP | Signal (RGB)
.......................
41
SETUP | Security
...............................
42
SETUP | Advanced
............................
44
SETUP | Network
...............................
45
OPTIONS
...........................................
50
OPTIONS | Advanced
........................
52
OPTIONS | Lamp Settings
.................
53
OPTIONS | PointBlank
......................
54
Ruby Introduction
..............................
56
How to use Web Control
...................
56
How to use the Card Reader
............
63
How to use the Optoma Presenter ... 66
Appendices
....................................
70
Troubleshooting
................................
70
Replacing the lamp
...........................
76
Replacing and cleaning the optional
dust filter
...........................................
78
Compatibility Modes
.........................
79
Computer Compatibility
.....................
79
Video Compatibility
............................
80
RS232 Commands and Protocol
Function List
.....................................
81
RS232 Pin Assignments
....................
81
RS232 Protocol Function List
............
82
Wall Mount Installation
......................
86
Optoma Global Offices
.....................
87
Regulation & Safety Notices
.............
89
Table of Contents