Optoma ZH507 Manual
Optoma ZH507 Manual
 |
View all Optoma ZH507 manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma ZH507 manual content summary:
- Optoma ZH507 | Manual - Page 1
DLP® Projector User manual - Optoma ZH507 | Manual - Page 2
TABLE OF CONTENTS SAFETY 4 Important Safety Instruction...4 Laser Radiation Safety Information 5 Copyright...7 Disclaimer...7 Trademark Recognition...7 FCC...7 Declaration of Conformity for EU countries 8 WEEE...8 Cleaning the Lens...8 INTRODUCTION 9 Package Overview...9 Standard accessories...9 - Optoma ZH507 | Manual - Page 3
resolutions...55 Image size and projection distance 58 Projector dimensions and ceiling mount installation 59 IR remote control 1 codes...60 IR remote control 2 codes...62 Troubleshooting...64 Warning indicators...66 Specifications...67 Optoma global offices...68 English 3 - Optoma ZH507 | Manual - Page 4
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Please follow all , precautions and maintenance as recommended in this user's guide. Important Safety Instruction ‡‡ Do not block any ventilation openings. To ensure - Optoma ZH507 | Manual - Page 5
2015. ‡‡ This projector is class 1 laser product of IEC/EN 60825-1:2014 and risk group 2 with the requirements of IEC 62471-5:2015. ‡‡ Additional instructions to supervise children, no staring, and not use optical aids. ‡‡ Notice is given to supervise children and to never allow them to stare into - Optoma ZH507 | Manual - Page 6
out of the lens, can cause an unpredictable outcome such as a fire or injury to the eyes. ‡‡ Any operation or adjustment not specifically instructed by the user's guide creates the risk of hazardous laser radiation exposure. ‡‡ Do not open or disassemble the projector as this may cause damage by the - Optoma ZH507 | Manual - Page 7
a trademark of Texas Instruments. All other product names used in this manual are the properties of their respective owners and are Acknowledged. FCC This energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there - Optoma ZH507 | Manual - Page 8
2014/30/EU (including amendments) ‡‡ Low Voltage Directive 2014/35/EU ‡‡ RED 2014/53/EU (if product has RF function) WEEE Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please - Optoma ZH507 | Manual - Page 9
Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Warranty Card* Quick start user manual Projector Remote control Power lead Documentation Note The remote control is shipped with batteries. * For warranty Information, please - Optoma ZH507 | Manual - Page 10
INTRODUCTION Product Overview 1 2 5 6 7 9 12 3 4 8 9 11 10 9 Note: ‡‡ ‡‡ Do not block projector intake and exhaust vents. When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake and exhaust vents. No Item 1. IR Receivers 2. Keypad 3. - Optoma ZH507 | Manual - Page 11
INTRODUCTION Connections 1 2 3 5 78 9 4 6 13 17 16 15 14 12 11 10 No Item 1. HDMI 2 Connector 2. Micro USB Connector 3. HDMI 1 Connector 4. USB Power Out (5V 1.5A) Connector 5. Video Connector 6. VGA In Connector 7. Audio In 1 Connector 8. Audio In 2 Connector 9. 3D Sync - Optoma ZH507 | Manual - Page 12
INTRODUCTION Keypad 1 2 3 4 5 6 10 No Item 1. Lamp LED 2. Power and Power LED 3. Menu 4. Keystone Correction 5. Enter 9 8 7 No Item 6. Temp LED 7. Re-Sync 8. Four Directional Select Keys 9. Source 10. Information 12 English - Optoma ZH507 | Manual - Page 13
18. Mouse Right Click 19. Four Directional Select Keys 20. Page + 21. Volume - / + 22. 3D Menu On / Off 23. VGA 24. Video (not supported) 25. User 3 (Assignable) 26. Numeric Keypad (0-9) 27. Resync The actual remote control may vary depending on the region. Some keys may have no function - Optoma ZH507 | Manual - Page 14
19. 3D Menu On / Off 20. Sleep Timer 21. Volume + 22. Re-Sync 23. Four Directional Select Keys 24. Volume - 25. HDMI2 26. YPbPr (not supported) 27. Video (not supported) The actual remote control may vary depending on the region. Some keys may have no function for models that do not - Optoma ZH507 | Manual - Page 15
SETUP AND INSTALLATION Installing the projector Your projector is designed to be installed in one of four possible positions. Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a - Optoma ZH507 | Manual - Page 16
SETUP AND INSTALLATION Projector installation notice ‡‡ 360° free orientation operation ‡‡ Allow at least 30 cm clearance around the exhaust vent. Minimum 100mm (3.94 inches) Minimum 300mm (11.81 inches) Minimum 300mm (11.81 inches) Minimum 100mm (3.94 inches) Minimum 100mm (3.94 inches) - Optoma ZH507 | Manual - Page 17
SETUP AND INSTALLATION Connecting sources to the projector 4 5 7 6 3 1 2 8 9 15 11 10 17 16 14 13 12 No Item 1. HDMI Cable 2. HDMI Dongle 3. USB Power Cable 4. Video Cable 5. Audio In Cable 6. VGA In Cable 7. RCA Component Cable 8. Audio In Cable 9. 3D Emitter Cable No Item - Optoma ZH507 | Manual - Page 18
SETUP AND INSTALLATION Adjusting the projector image Image height The projector is equipped with elevator feet for adjusting the image height. 1. Locate the adjustable foot you wish to adjust on the underside of the projector. 2. Rotate the adjustable foot clockwise or counterclockwise to raise or - Optoma ZH507 | Manual - Page 19
the same or equivalent type batteries. CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. ‡‡ Do not mix batteries of different types. Different types of batteries have different characteristics. ‡‡ Do not mix old and new batteries - Optoma ZH507 | Manual - Page 20
1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Keystone -+ Volume -+ Page- Mode Page+ Enter L R Freeze SETUP AND INSTALLATION Effective range Infra-Red (IR) remote control sensor is located on the top and front sides of the projector. Ensure to hold the remote - Optoma ZH507 | Manual - Page 21
USING THE PROJECTOR Powering on / off the projector Power Switch or Freeze L R Enter Page- Mode Page+ Keystone -+ Volume -+ 1 2 3 Menu 3D 4 HDMI 5 VGA 6 Video 7 User1 8 User2 9 User3 0 Source Resync Powering on 1. Securely connect the power lead and signal/source cable. - Optoma ZH507 | Manual - Page 22
USING THE PROJECTOR Freeze L R Enter Selecting an input source Turn on the connected source that you want to display on the screen, sucPKhaegyeas-tosneMcoodemVopPluaumgteee+ r, notebook, video player, etc. The projector will automatically detect the source. If multiple sources -are +conn-ecte - Optoma ZH507 | Manual - Page 23
settings. Sub Menu Settings Main Menu Display Image Settings Enhanced Gaming 3D Aspect Ratio Edge Mask Digital Zoom Image Shift Geometric Correction Select Exit Navigation guide Off Enter English 23 - Optoma ZH507 | Manual - Page 24
USING THE PROJECTOR OSD Menu tree Note: The OSD menu tree items and features are subject to models and region. Optoma reserve the right to add or remove items to improve product performance without notice. Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Display Mode Wall Color HDR / HLG Display - Optoma ZH507 | Manual - Page 25
USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Sub Menu 3 BrilliantColorTM Color Temperature Sub Menu 4 Color Display Color Matching Hue / R(*) Saturation / G(*) Gain / B(*) Color Settings Image Settings RGB Gain/Bias Reset Exit Red Gain Green Gain Blue Gain Red Bias Green Bias Blue - Optoma ZH507 | Manual - Page 26
USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Signal H. Position V. Position Image Settings Brightness Mode Enhanced Gaming Reset 3D Mode 3D Tech 3D 2D 3D Display 3D Format 3D Sync Invert Reset Aspect Ratio Edge Mask Digital Zoom Image Shift Geometric Correction H V - Optoma ZH507 | Manual - Page 27
USING THE PROJECTOR Main Menu Sub Menu Mute Volume Sub Menu 2 Sub Menu 3 HDMI1 Audio Audio Input HDMI2 VGA Video Projection Setup Direct Power On Signal Power On Auto Power Off (min.) Power Settings Sleep Timer (min.) Always On Power Mode (Standby) USB Power (Standby) Security - Optoma ZH507 | Manual - Page 28
USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 HDMI Link HDMI Link Settings Inclusive of TV Power On Link Sub Menu 3 Power Off Link Test Pattern IR Function F1 Setup Remote Settings [depends on remote] F2 F3 12V Trigger Sub Menu 4 Values Off [Default] On No [Default] Yes Mutual - Optoma ZH507 | Manual - Page 29
USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Language Setup Options Closed Captioning Menu Settings Menu Location Menu Timer Auto Source Sub Menu 4 Values English [Default] Deutsch Français Italiano Español Português Polski Nederlands Svenska Norsk/Dansk Suomi Magyar - Optoma ZH507 | Manual - Page 30
USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Input Source Options Setup HDMI1 Input Name HDMI2 VGA Video High Altitude Display Mode Lock Keypad Lock Information Hide Logo Background Color Reset Reset OSD Reset to Default Auto upgrade FW Sub Menu 4 Values HDMI1 - Optoma ZH507 | Manual - Page 31
USING THE PROJECTOR Main Menu Sub Menu LAN Sub Menu 2 Network Status MAC Address DHCP IP Address Subnet Mask Gateway DNS Reset Crestron Sub Menu 3 Network Extron Control PJ Link AMX Device Discovery Telnet HTTP Regulatory Serial Number Source Resolution Refresh Rate Display Mode - Optoma ZH507 | Manual - Page 32
USING THE PROJECTOR Display menu Display image settings menu Display Mode There are several predefined display modes that you can choose from to suit your viewing preference. Each mode has been fine-tuned by our expert colour team to ensure superior colour performance for wide range of content. ‡‡ - Optoma ZH507 | Manual - Page 33
Dynamic Range (HDR) / Hybrid Log Gamma(HLG) setting and its effect when displaying videofrom 4K Blu-ray players and streaming devices. Note: Only HDMI supports the Dynamic Range function. HDR / HLG ‡‡ Off: Turn off HDR/HLG Processing. When set to Off, the projector will NOT decode HDR/HLG content - Optoma ZH507 | Manual - Page 34
USING THE PROJECTOR Color Settings Configure the color settings. ‡‡ BrilliantColorTM: This adjustable item utilizes a new color-processing algorithm and enhancements to enable higher brightness while providing true, more vibrant colors in picture. ‡‡ Color Temperature: Select a color temperature - Optoma ZH507 | Manual - Page 35
USING THE PROJECTOR Brightness Mode Adjust the brightness mode settings. ‡‡ DynamicBlack: Use to automatically adjust the picture brightness in order to give optimum contrast performance. ‡‡ Eco.: Choose "Eco." to dim the projector laser diode which will lower power consumption and extend the - Optoma ZH507 | Manual - Page 36
glasses are use for DLP-Link 3D before enjoy your video. This projector supports frame sequential (page-flip) 3D via HDMI1/HDMI2/VGA ports. To enable 1920x1080 is recommended, please be noted that 4K (3840x2160) resolution is not supported in 3D mode. 3D Mode Use this option to disable or enable - Optoma ZH507 | Manual - Page 37
. ‡‡ If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1 content (include Anamorphic DVD and HDTV film source) that supports anamorphic wide is enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Light source power and vertical - Optoma ZH507 | Manual - Page 38
USING THE PROJECTOR Display edge mask menu Edge Mask Use this function to remove the video encoding noise on the edge of video source. Display digital zoom menu Digital Zoom Use to reduce or magnify an image on the projection screen. Digital Zoom is not the same as optical zoom and an result in - Optoma ZH507 | Manual - Page 39
USING THE PROJECTOR Audio menu Audio mute menu Mute Use this option to temporarily turn off the sound. ‡‡ On: Choose "On" to turn mute on. ‡‡ Off: Choose "Off" to turn mute off. Note: "Mute" function affects both internal and external speaker volume. Audio volume menu Volume Adjust the volume level - Optoma ZH507 | Manual - Page 40
USING THE PROJECTOR Setup menu Setup projection menu Projection Select the preferred projection between front, rear, ceiling-top, and rear-top. Setup power settings menu Direct Power On Choose "On" to activate Direct Power mode. The projector will automatically power on when AC power is supplied, - Optoma ZH507 | Manual - Page 41
USING THE PROJECTOR Setup security menu Security Enable this function to prompt for a password before using the projector. ‡‡ On: Choose "On" to use security verification when the turning on the projector. ‡‡ Off: Choose "Off" to be able to switch on the projector without password verification. - Optoma ZH507 | Manual - Page 42
0-99), and allow user control an individual projector by using RS232 command. Note: For a full list of RS232 commands, please refer to the RS232 user manual on our website. Setup 12V trigger menu 12V Trigger Use this function to enable or disable the trigger. ‡‡ Off: Choose "Off" to disable the - Optoma ZH507 | Manual - Page 43
. ‡‡ Neutral: Logo is not displayed on startup screen. ‡‡ User: Logo capture tool required. Note: Please visit the website to download the logo capture tool. The supported file format: png/bmp/jpg. English 43 - Optoma ZH507 | Manual - Page 44
USING THE PROJECTOR Background Color Use this function to display a blue, red, green, gray color, none, or logo screen when no signal is available. Note: If the background color is set to "None", then the background color is black. Setup reset OSD menu Reset OSD Return the factory default settings - Optoma ZH507 | Manual - Page 45
-only). DHCP Use this option to enable or disable the DHCP function. ‡‡ Off: To assign IP, subnet mask, gateway, and DNS configuration manually. ‡‡ On: Projector will obtain an IP address automatically from your network. Note: Exiting OSD will automatically apply the entered values. IP Address - Optoma ZH507 | Manual - Page 46
USING THE PROJECTOR Making a direct connection from your computer to the projector* 1. Turn "Off" the DHCP option on the projector. 2. Configure the IP address, Subnet Mask, Gateway, and DNS on projector ("Network > LAN"). 3. Open Network and Sharing Center page on your PC, and assign the identical - Optoma ZH507 | Manual - Page 47
United States of America, and other countries by JBMIA. The projector is supported by the specified commands of the Crestron Electronics controller and related software, projector, as well as the supported commands for these external devices, please contact the Support-Service directly. English 47 - Optoma ZH507 | Manual - Page 48
USING THE PROJECTOR LAN RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop). 2. On the PC (Laptop), select Start > Control Panel > Network Connections. 3. Right-click on the Local Area Connection, and select Property. 4. In the Properties window, select the General tab, - Optoma ZH507 | Manual - Page 49
USING THE PROJECTOR 5. Click "Properties". 6. Type in the IP address and Subnet mask, then press "OK". 7. Press the "Menu" button on the projector. 8. Open on projector Network > LAN. 9. Enter the following connection parameters: ±± DHCP: Off ±± IP Address: 192.168.0.100 ±± Subnet Mask: 255.255.255 - Optoma ZH507 | Manual - Page 50
USING THE PROJECTOR The projector is setup for remote management. The LAN / RJ45 function displays as follows: General Setup Network Setup Projector Control 50 English - Optoma ZH507 | Manual - Page 51
USING THE PROJECTOR System Status English 51 - Optoma ZH507 | Manual - Page 52
For a full list of RS232 commands, please refer to the RS232 user manual on our website. Quick Start-Guide for "RS232 by Telnet" ‡‡ Check and get the IP address on port: 23 (for more detail, kindly please get contact with the service agent or team). 3. Telnet utility: Windows "TELNET.exe" (console - Optoma ZH507 | Manual - Page 53
USING THE PROJECTOR Info menu Info menu View the projector information as listed below: ‡‡ Regulatory ‡‡ Serial Number ‡‡ Source ‡‡ Resolution ‡‡ Refresh Rate ‡‡ Display Mode ‡‡ Power Mode (Standby) ‡‡ Light Source Hours ‡‡ Network Status ‡‡ IP Address ‡‡ Projector ID ‡‡ Brightness Mode ‡‡ FW - Optoma ZH507 | Manual - Page 54
MAINTENANCE Installing and cleaning the dust filter Installing the dust filter 2 1 Note Dust filters are only supplied with some models in select region with excessive dust. Not available in North America or Europe. You may be available to purchase this in select regions. Please visit our - Optoma ZH507 | Manual - Page 55
ADDITIONAL INFORMATION Compatible resolutions Analog B0 / Established Timing 720 x 400 @ 70Hz 640 x 480 @ 60Hz 640 x 480 @ 66.6(67)Hz 640 x 480 @ 72Hz 640 x 480 @ 75Hz 800 x 600 @ 56Hz 800 x 600 @ 60Hz 800 x 600 @ 72Hz 800 x 600 @ 75Hz 832 x 624 @ 75Hz 1024 x 768 @ 60Hz 1024 x 768 @ 70Hz 1024 x - Optoma ZH507 | Manual - Page 56
ADDITIONAL INFORMATION HDMI 2.0 B0 / Established Timing B0 / Standard Timing B0 / Detail Timing B1 / Video Mode B1 / Detail Timing 720 x 400 @ 70Hz 1280 x 720 @ 60Hz 1920 x 1080 @ 60Hz 640 x 480p 4:3 @ 60Hz 1920 x 1080 @ 60Hz 640 x 480 @ 60Hz 1280 x 800 @ 60Hz 720 x 480p 4:3 @ 60Hz 1366 - Optoma ZH507 | Manual - Page 57
@ 60Hz 480i HQFS 3D format is Frame sequential Note: ‡‡ If 3D input is 1080p@24Hz, the DMD should replay with integral multiple with 3D mode. ‡‡ Support NVIDIA 3DTV Play if there is no patent fee from Optoma. ‡‡ 1080i@25Hz and 720p@50Hz will run in 100Hz; 1080p@24Hz will run in - Optoma ZH507 | Manual - Page 58
ADDITIONAL INFORMATION Image size and projection distance Diagonal Length Size of (16:9) Screen Screen Size (W x H) (m) (inch) Width Height Width Height 20.2 40 50 60 70 80 90 100 120 150 180 200 250 320.4 0.45 0.25 17.61 9.9 0.89 0.5 34.86 19.6 1.11 0.62 43.58 24.5 1.33 0.75 52.29 29.4 - Optoma ZH507 | Manual - Page 59
ADDITIONAL INFORMATION Projector dimensions and ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following - Optoma ZH507 | Manual - Page 60
ADDITIONAL INFORMATION IR remote control 1 codes Power Switch Freeze L R Power Switch Freeze L R Enter Enter Page- Laser Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Page- Mode Page+ Keystone -+ Volume -+ 1 4 HDMI 7 - Optoma ZH507 | Manual - Page 61
as numeric keypad number "1". ‡‡ Press to display or exit the on-screen display menus for projector. ‡‡ Use as numeric keypad number "2". ‡‡ Press to manually select a 3D mode that matches your 3D content. ‡‡ Use as numeric keypad number "3". ‡‡ Press to choose HDMI source. ‡‡ Use as numeric keypad - Optoma ZH507 | Manual - Page 62
ADDITIONAL INFORMATION IR remote control 2 codes ON OFF User1 User2 Contrast Brightness User3 Mode Aspect ratio Keystone Mute DB 3D Sleep Timer Volume Source Re-sync Menu Volume HDMI1 HDMI2 VGA1 VGA2 Video YPbPr Key Power on Power off User 1 User 2 User 3 Brightness Contrast - Optoma ZH507 | Manual - Page 63
0F 04 0C 0E 16 30 1B 1E 1C 17 Printingkey definition Aspect ratio 3D Volume Description Press to change aspect ratio of a displayed image. Manually select a 3D mode that matches your 3D content. Adjust to increase volume. Use or ▼ to select items or make adjustments to your selection. Source - Optoma ZH507 | Manual - Page 64
ADDITIONAL INFORMATION Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image problems N o image appears on-screen ‡‡ Ensure all the cables and power connections - Optoma ZH507 | Manual - Page 65
to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within ±30° to the IR receiver on the - Optoma ZH507 | Manual - Page 66
again. If the warning indicator light up or flash, please contact your nearest service center for assistance. LED lightning messages Message Standby state (Input power cord) under 45 degree C. If the problem persists in spite of the above. Please contact a service center for repair. 66 English - Optoma ZH507 | Manual - Page 67
.4) ‡‡ VGA In ‡‡ VGA Out ‡‡ Video ‡‡ USB Type-A for Power USB 5V/1.5A ‡‡ Micro USB (for service) ‡‡ Audio In 3.5mm (x2) ‡‡ Audio Out 3.5mm ‡‡ MIC In ‡‡ 12V Out ‡‡ 3D SYNC ‡‡ RS232 ‡‡ RJ-45 (support web control) 1073.4 Million color ‡‡ Horizontal scan rate: 15.375~91.146 KHz ‡‡ Vertical scan rate: 50 - Optoma ZH507 | Manual - Page 68
ADDITIONAL INFORMATION Optoma global offices For service or support, please contact your local office. USA 47697 Westinghouse Drive, Fremont, CA 94539, USA www.optomausa.com Japan 888-289-6786 510-897-8601 [email protected] 3-25-18 0120-380-495 [email protected] www.os-worldwide.com - Optoma ZH507 | Manual - Page 69
www.optoma.com
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
 |
 |
DLP
®
Projector
User manual