Panamax MIW-SURGE Manual

HDMI cable passed through hole cut out in

rubber grommet. Remove rubber, cut hole,

push the cable(s) through and replace

grommet with cable into the insert.

3.

Dual gang

plastic outlet

box, new work

INS00847

REV. D

11/10

MIW-SURGE

Installation Instructions

PFPower, 1690 Corporate Circle • Petaluma, CA 94954

707-283-5900 •

800-472-5555 • Fax - 707-283-5901

www.panamax.com • www.furmansound.com

Customer Relations

7:30 AM – 4:30 PM, M-F, Pacific Time (PST)

Email - [email protected]

By

Panamax

~

Furman

By

Panamax

~

Furman

5.

Decora

®

trim

plate adapter

6.

Keystone module

insert

7.

11” Flat Plug

adapter power cord

8.

Three wire

twist nuts

9.

Wall cut out tem-

plate 3 3/4” H x 4” W

AC Circuit

AC Outlets, Total:

............................................................................

1

Line Voltage:

..............................................................

120V, 50/60Hz

Total Current Capacity:

................................................................

15A

Protection Modes:

........................................................

L-N, L-G, N-G

Energy Dissipation:

.........................................................

1350 Joules

Peak Impulse Current:

..............................................................

60 KA

Catastrophic Surge Circuit:

..........................................................

Yes

Thermal Fusing:

..........................................................................

Yes

UL 1449 2nd Ed. Suppressed Voltage Rating:

..............

330 V (@500A)

UL 1449 3rd Ed. Voltage Protection Rating:

..............

400 V (@3,000A)

UL 1449 3rd Ed. Nominal Discharge Current:

.........................

5,000A

Power Outlet Faceplate

AC Connectors:

...........................................................

1 NEMA 5-15

Signal Line Protection: Not Included / Modules Sold Separately

PRODUCT SPECIFICATIONS

The MIW-SURGE is designed essentially for compatibility with three basic configurations:

PFPower warrants to the purchaser of any

PFPower In-Wall surge protector, for a pe-

riod of 3 years from its installation date,

that the surge protector shall be free of

defects in design, material, or workman-

ship, and PFPower will repair or replace

any defective unit. For product replace-

ment see “NOTIFICATION” below.

CAUTION:

Audio/Video, computer and/

or telephone system installations can be

very complex systems, which consist of

many interconnected components. Due

to the nature of electricity and surges, a

single protector may not be able to com-

pletely protect complex installations.

In

those cases, a systematic approach using

multiple protectors must be employed.

Systematic protection requires profes-

sional design.

AC power, satellite cables,

CATV cables, or telephone/network lines

entering the system that do not pass

through this surge protector will provide

pathways for potential surge damage.

For

additional information on how to protect

your system, please contact PFPower

before connecting your equipment to the

surge protector. More detailed informa-

tion is available at www.panamax.com or

www.furmansound.com. If you have any

questions regarding these requirements,

please contact PFPower Customer Rela-

tions.

1. PROPER

INSTALLATION:

PFPower

In-Wall AC and Signal-line protectors are

designed to provide code-compliant (NEC

or CEC) installations.

Separate signal-line

protection modules must be used with the

appropriate AC base unit to provide proper

grounding.

Building wiring and other con-

nections to protected equipment must

conform to applicable codes (NEC or CEC).

No other ground wires or ground connec-

tions may be used.

All wires (including,

AC power lines, telephone lines, signal/

data lines, coaxial cable, antenna lead-

ins) leading into the protected equipment

must first pass through a single PFPower

protector designed for the particular ap-

plication.

The protector and the equip-

ment to be protected must be indoors in

a dry location, and in the same building.

PFPower installation instructions and dia-

grams must be followed.

2. NOTIFICATION:

You must obtain a re-

turn authorization (RA) number from the

PFPower Customer Relations Department

at www.panamax.com or www.furman-

sound.com or toll-free at 1-800-472-

5555 before returning the protector to

PFPower. Once you obtain an RA number,

please mark the number on the bottom of

the unit and pack it in a shipping carton/

box with enough packing material to pro-

tect it during transit.

The RA number must

be clearly marked on the outside of the

carton. Ship the unit to PFPower.

Please

note that you are responsible for any and

all charges related to shipping the unit to

PFPower.

3. DETERMINATION OF FAILURE:

PFPower will evaluate the protector for

defects.

Opening the enclosure, tamper-

ing with, or modifying the unit in any way

shall be grounds for an automatic denial

of your request for replacement. PFPower,

after evaluating the unit, shall in its sole

discretion, determine whether or not your

protector is eligible for replacement. If the

surge protector shows no defects, PF-

Power will return the unit to you with a let-

ter explaining the test results. Exception: If

a dealer or installer replaces the protector

for the customer, the unit will be returned

to the dealer or installer.

4. GENERAL:

If you have any questions

regarding the product warranty, please

contact the Customer Relations Depart-

ment at www.panamax.com or www.

furmansound.com or toll-free at 1-800-

472-5555.

This warranty supersedes

all previous warranties. This is the only

warranty provided with the protector and

any other implied or expressed warranties

are non-existent. This warranty may not

be modified except in writing, signed by

an officer of PFPower.Forms are available

on the Panamax or Furman web sites for

requesting RA’s.

MODEL - MIW-SURGE

DOC. NO.

Q01L0047_EN REV. A

Effective Date 6/08

WARRANTY

MIW PRO SIGNAL LINE MODULES

1. MIW-5RCA

Low voltage module with 5 RCA connec-

tions compatible with component video or

composite audio/video signal.

2. MIW-VGA

Low voltage module for RGBHV; connect

devices to 15 pin high-density D-sub

connector on face of module; 3.5mm

stereo mini-jack for 12-volt triggering

and IR signal transmission.

3. MIW-SVIDEO

Combination S-Video and Component Video,

low voltage module for video and/or audio,

RCA jacks compatible with audio or video

signals.

4. MIW-DATA

RS232 and Ethernet, low Voltage module

for projector control lines and/or computer

data lines.

The MIW Pro Signal Line modules give you 4 options to choose from.

Each signal line module comes with an instructions for easy install.

The MIW Pro Signal Line modules are not included and sold separately from PFPower.

Contact Panamax or Furman to order module(s) and other products you may need.

1. PASS THROUGH INSERT

with rubber grommet accomo-

dates HDMI, RGB, or coaxial

cables.

2. KEYSTONE 2 PORT

ADAPTER INSERT

with module selection. NOTE: If using

a punchdown connector, punch down

wires first before inserting module

into KEYSTONE insert.

(Modules for

KEYSTONE adapter insert are sold sepa-

rately and

not

available from PFPower)

3. DECORA TRIM ADAPTER

for 6 port insert for a variety of signal

line connections.

(6 port insert and modules are sold sepa-

rately and

not

available from PFPower)

4. MIW PRO SIGNAL LINE

MODULES

Four module types available.

1. MIW-RCA

2. MIW-VGA

3. MIW-SVIDEO 4. MIW-DATA.

(Modules not included, sold separately

and available from PFPower, see below for

module descriptions).

Adjustable 3 depth settings for:

•

PASS THROUGH INSERT

• KEYSTONE ADAPTER

•

ALL 4 MIW PRO SIGNAL LINE MODULES.

3.

1 inch deep

1.

Flush with

faceplate

2.

1/2 inch deep

Remove PASS THROUGH INSERT ASSEMBLY

(cage) and place Decora 6 port insert

with modules you need onto the

front of the mounting bracket .

Place Decora trim plate

adapter over the Decora insert.

Use the 2 screws/lock nuts

that attached the PASS THROUGH

INSERT.

Remove the black rubber grommet

from the PASS THROUGH INSERT

and snap KEYSTONE adapter into

open slot.

To install MIW PRO

SIGNAL LINE MODULES,

simply remove insert

from assembly and

insert the MODULE.

Insert

Remove

1

.

Single gang

plastic outlet

box, retro

2.

Single gang

metal outlet

box, new work

1.

MIW-SURGE metal

outlet faceplate (AC

receptacle attached)

2.

4 flathead faceplate

screws and 2 pan head

screws for bracket

3.

MIW-SURGE plastic

mounting bracket

4.

MIW pass through

removable and adjust-

able insert with rubber

grommet (comes at-

tached to mounting

bracket)

PARTS INCLUDED:

Outlet boxes are

NOT

included and are sold separately.

TOOLS RECOMMENDED:

•

Drywall saw or Dremel tool (to cut outlet box hole)

•

Hand held or power screw driver with Phillips head

•

File (optional) to smooth and shape the outlet box cutout (if necessary)

•

Utility knife

•

Combination strippers

•

Long nosed pliers

SIGNAL LINE CONNECTION OPTIONS

Installation instructions for using MIW-SURGE with

G

N

L

G

N

L

15 Amp

Circuit Breaker

Electric Panel

MIW-SURGE

Minimum

14 Gauge Wire

US PATENT NOS.

6,932,624

6,979,205

7,271,991

US PATENT PENDING

CAUTION:

USE ONLY IN DRY (INDOOR) LOCATIONS.

ATTENTION:

PAR L’USAGER A L’INTERÉRIEUR.

WALL MOUNTING THICKNESS

3/8” - 5/8”

MIW-SURGE

MIW-XT

L

N

G

BLACK

WHITE

GROUND

Suppressed Voltage Rating: 330V @ 500A

Voltage Protection Rating: 400V @ 3KA

US PATENT NOS.

6,932,624

6,979,205

7,271,991

5

6

1

Panamax MIW-SURGE Manual

Panamax MIW-SURGE Manual

Panamax MIW-SURGE manual content summary: