Panasonic NN-TK903S User Manual

CAUTION

1.

Read and follow all instructions completely.

2. This Trim Kit is designed for use only with the

Microwave Ovens listed in the table, and where

operating instructions make reference to the instal-

lation of this Trim Kit.

3. For safe use of your oven, do not alter or modify

any part

of this kit or oven.

4. Oven must be plugged into a properly grounded

3-prong receptacle as is required by National

Electrical Code or any other applicable regulations.

5. Before attempting the installation of this kit, be sure

to unplug the oven from wall receptacle.

6.

Save these instructions for local inspection and relo-

cation of oven.

1. CABINET OPENING

1.

The cabinet opening should be as follows.

・

Width : 24

7

/

8

"

±

1

/

16

"

(63.2 cm

±

0.16 cm)

・

Height : 18

1

/

16

"

±

1

/

16

"

(45.9 cm

±

0.16 cm)

・

Depth : 21

"

(53.3 cm) minimum.

Refer to Fig. (1).

The overall outside dimensions of 27

"

type trim

kits are 27

"

(68.6 cm) wide and 30

"

type trim

kits are 30

"

(76.2 cm) wide and 19

1

/

2

"

(49.6 cm)

high for both types of trim kits. Refer to Fig. (3).

2.

The floor of the opening must be capable of sup-

porting 100 lbs (45 kg) and should be plywood.

3. The cabinet opening at ceiling should have a

clearance of at least 1

3

/

4

"

(4.5 cm) to rear wall

W

.

Refer to Fig. (1).

Fig. (1)

MICROWAVE OVEN BUILT-IN TRIM KITS

INSTALLATION INSTRUCTIONS

PARTS LIST

Quantity

(A) Runner

………………………

2

(B)

Exhaust Cover

………………

1

(C) Base

…………………………

1

(D)

Exhaust Cover

………………

1

(E)

Air Guide

……………………

1

(F)

Top and bottom trim strip

…

2

(G)

Side trim strip

………………

2

(H)

Screw (large diameter)

……

5

(I)

Screw (long)

…………………

4

(J)

Screw (short)

………………

7

(K)

Screw (small diameter)

……

8

(L) Blind

…………………………

1

30

"

(76.2 cm)

19

1

/

2

"

(

49.6 cm

)

27

"

(68.6 cm)

19

1

/

2

"

(

49.6 cm

)

2. BRACKET INSTALLATION

1. Position Base (C) on the plywood floor, spaced approx.

1

/

2

"

(1.3 cm) from the left side and

1

/

2

"

(1.3 cm) from the right side.

The front end of Base (C) shall be aligned flush with the front

edge of the plywood floor. Refer to Fig. (1).

2. Place the two Runners (A) and Air Guide (E) on the Base (C),

and secure with the 5 wood Screws (H) onto the plywood floor

as shown in Fig. (2).

Fig. (2)

Fig. (3)

NN-TK913S

NN-TK913B

NN-TK913W

NN-TK903S

NN-TK903B

NN-TK903W

OVEN MODELS

NN-C994S, NN-CD989S

NN-C980B, NN-C988B, NN-9809, NN-9509, NN-9500, NN-9509P

NN-9800, NN-9804

NN-C980W, NN-C988W, NN-9859, NN-9850, NN-9854, NN-9854P

MQC1548H

NN-C994S, NN-CD989S

NN-C980B, NN-C988B, NN-9809, NN-9509, NN-9500, NN-9509P

NN-9800, NN-9804

NN-C980W, NN-C988W, NN-9859, NN-9850, NN-9854, NN-9854P

MQC1548H

30"cabinet

27"cabinet

NN-TK913S(Metal)

NN-TK913B(Black)

NN-TK913W(White)

NN-TK903S(Metal)

NN-TK903B(Black)

NN-TK903W(White)

TRIM KITS

A0003A951AP

0609

Printed in Japan

3. OVEN PREPARATION

1. Remove two screws and exhaust cover (originally

installed) shown in Fig.(6) from the rear of the oven.

Retain the Exhaust Cover for future use in case the oven

is removed for countertop use.

2. Insert the tab of Exhaust Cover (D) into the slot on the

rear of oven and secure with three Screws (J).

3. Place Exhaust Cover (B) on the top of the oven and

secure with two Screws (J)

shown in Fig.

(

6

)

.

4. OVEN INSTALLATION

1. Plug the power cord into wall receptacle and slide the

oven in on the Runner (A) until the oven rests in the

detents of the Runner (A).

Use caution so that the cord is not pinched. Fig.(4).

2.

Place Blind (L) on the top of Runner (A) and secure with

two Screws (J)

shown in Fig.

(

5

)

.

Fig. (4)

Fig. (6)

Fig. (5)

Side Trim Strip (G)

Rear side of Trim Strip

Top & Bottom Trim Strip (F)

Screws (K)

Screws (I)

TRIM KIT FRAME

Fig. (7)

Fig. (8)

5. TRIM ASSEMBLY

1.

Assemble Top & Bottom Trim Strips (F) and two Side Trim

Strips (G) by Screws (K) at each of 4 corners of rear side

trim (each corner uses 2 screws) . Refer to Fig.(7).

6. TRIM INSTALLATION

1. After the oven is properly installed, center the trim kit

frame around the oven.

2. Use the assembled trim kit frame as a template and mark

the four holes for drilling pilot holes.

3. Position the trim kit frame and secure to cabinet with

Screws ( I ) .Refer to Fig.(8).

Panasonic NN-TK903S User Manual

Panasonic NN-TK903S Manual

Panasonic NN-TK903S manual content summary: