Panasonic PT-DW100U Dlp Projector - Multi Language

Panasonic PT-DW100U - WXGA DLP Projector Manual

Get Panasonic PT-DW100U - WXGA DLP Projector PDF manuals and user guides View all Panasonic PT-DW100U manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic PT-DW100U manual content summary:

  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 1
    Operating Instructions DLP® Based Projector Commercial Use PT-D10000U Models No. PT-DW10000U Read these instructions completely before operating this unit. TQBJ 0208
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 2
    , and that you will be pleased with your Panasonic DLP® based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D10000U/PT-DW10000U Serial number: 2 - ENGLISH
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 3
    the serial terminals 102 Using the Remote 2 terminal 106 Special Features Information Indication of monitor lamp 107 Cleaning and replacement of air filter 108 Replacement of lamp unit 110 Notes when installing the ceiling mount bracket 112 Before asking for service ... try to check the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 4
    of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 5
    user's authority to operate. WARNING: Not for use PT-D10000U / PT-DW10000U Panasonic Panasonic North America One Panasonic Way 4B-9 Secaucus, NJ 07094 1-800-524-1448 or 1-800-526-6610 [email protected] This device complies with Part Intensity Discharge (HID) lamp that contains a small
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 6
    is broken, turn off the power and disconnect the power cord from the wall outlet. • Continued use of the projector in this condition may result in fire or electric shocks. • Contact an Authorized Service Center for repairs. ■ Do not cover the air filter, the air inlet and exhaust vents. • Doing
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 7
    Replacement of the lamp unit should be carried out by a qualified technician. • The lamp unit has high internal pressure. If improperly handled, failure might result. • The lamp . ■ Do not use the projector while the projection lens cover is still attached to the projection lens (sold separately). •
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 8
    ■ Do not look into the lens while the projector is being used. • Strong light is emitted from the projector's lens. If you look directly into this cannot withstand heat. ■ Do not use the old lamp unit. • The lamp section may break. ■ Replacement of the lamp unit should only be carried out after
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 9
    Ask your dealer to replace the lamp unit and check the inside of the projector. ■ Ask an Authorized Service Center to clean inside the projector at least once a year. • If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. • It
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 10
    Using Accessories Check that all of the accessories shown below have been included with your projector. Remote Control [N2QAYB000076 × 1] Batteries for Remote lens cover when installing the projection lens. If this is not done, dust will collect inside the projector and problems with the projector
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 11
    the lamp is used beyond the replacement time. ■ Maintenance Be sure to remove the power cord plug from the receptacle before cleaning. ● Use soft and dry cloth to clean the cabinet Use a soft cloth moistened in warm water to clean away oil. If a chemical wipe is used, follow its instructions. ● Do
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 12
    and function of each part Remote control unit ■ Front # $ % 0 & ( 1 ) * 2 3 + 4 - . 5 / 6 7 # Remote control operation indicator lamp The lamp flashes when any remote control button is pressed. $ POWER STANDBY button pp. 34, 36) When the projector is in projection mode
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 13
    8 LOCK button This button is used to prevent unintentional operation of the projector by accidentally pressing a button, and to prevent the remote control batteries from becoming spent. 9 Remote control transmitter window Operate the remote control aiming at the remote control receiver window on the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 14
    Location and function of each part (continued) Projector Main Unit ■ Front ■ Rear # $ % &( ) * 2 * + -. / 0 1 34 56 # Projectin lens cover p. 33) $ Projection lens (optional) Lens for projecting images on the screen. % Remote control receiver window (front) .. (p. 17) This window receives
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 15
    $ MAIN POWER switch pp. 35, 36) Use this switch to turn on "I" and off "○" the commercial line power applied to the projector. % Slot cover p. 28) Install the the level. Also use them to enter the "SECURITY" password. + LENS button p. 37) Switches to the adjustment mode for lens focus, zoom and
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 16
    each part (continued) ■ Connection terminals # $ % & ( ) *+ - ./ 0 # REMOTE1 lN/OUT terminal p. 18) When two or more main units are used in the system, they can be connected and controlled with a wired remote control cable (M3 jack). $ REMOTE2 IN terminal p. 106) The user can remotely
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 17
    - side first). 3. Close the battery compartment lid. • Replace the battery compartment lid over the compartment and slide until it clicks. Attention • Do not drop the Remote Control unit. • Do not expose Remote Control unit to any liquid. • Do not use NiCd batteries. • Release the LOCK button before
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 18
    . However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the batteries are replaced, set the same ID number again. Using a wired remote control When multiple main units are connected as part of the system, connect to units with a M3 stereo mini jack
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 19
    on the main unit. The following are some examples of system expansion: System 1 The optional high- or low-ceiling mount bracket flexibly fits the projector in individual site conditions. System 2 Connection to a computer via the DVI-D IN terminal or DVI-D input module (optional). ENGLISH - 19
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 20
    , the value will be fixed at H=SH/2 for both the PT-D10000U and PT-DW10000U. If the ET-D75LE6 has been installed, the values will be H = 0.1 × SH to 0.9 × SH for the PT-D10000U, and H = 0 to SH for the PT-DW10000U. 20 - ENGLISH L Screen Lens ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE5 ET
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 21
    involve an error of ±5 %. • Keystone distortions are corrected in the way the screen size becomes smaller than the original one. ■ Projection distances by the type of projection lenses (for PT-DW10000U) ● For the screen aspect ratio of 16:9 (Units: m (feet/inches)) Lens type Zoom lens Fixed-focus
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 22
    Installation (continued) ■ Projection distances by the type of projection lenses (for PT-D10000U) ● For the screen aspect ratio of 4:3 (Units: m (feet/inches)) Lens type Zoom lens Fixed-focus lens Model number of projection lens Throw ratio*1 ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 23
    Started If the projector is used with a screen size not listed in this manual, check the diagonal dimension (inch) of your screen and calculate the projection distance using the following formulas. ■ Calculation formulas for projection distance by lens types (for PT-DW10000U) Model number of
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 24
    carefully the instruction manual for the module (p. 27). • Some PC models cannot be connected to the projector. ● The pin-out and signal names of the S-VIDEO IN below. Outside view Pin No. # $ % 1 2 R/PR G/G • SYNC/Y B/PB HD/SYNC VD Signal &, -, 0, and 3 are not assigned. ( - +, . and /
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 25
    base corrector (TBC) or use a TBC between the projector and the video deck. • If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC between the projector and the video deck. Note • The DVI-D signal input terminal supports only a single link. • The
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 26
    ) Example of connecting with personal computers Control PC Control PC To 2nd projector (SERIAL IN terminal) IN OUT REMOTE 1 REMOTE 2 IN RS-232C IN RS-422 IN SERIAL RS-422 OUT LAN IN OUT VIDEO S-VIDEO IN R/PR G/Y SYNC/HD RGB 1 IN B/PB VD RGB 2 IN DVI-D IN Control PC I/F PC PC
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 27
    input × 1*1 Signal formats supported SMPTE259M compliant : 480i, 576i 10BASE-T/100BASE-TX HD/SD-SDI input module used with the PT-D10000U/PT-DW10000U. Use the LAN terminal that is provided as standard with the projector. *2: HDCP (High-bandwidth Digital Content Protection) HDCP is a specification
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 28
    ) (continued) ■ Procedure of installation Disconnect the power before installing the input module. IN OUT REMOTE 1 REMOTE 2 IN RS-232C IN RS-422 IN SERIAL RS-422 OUT LAN IN OUT VIDEO S-VIDEO IN R/PR G/Y SYNC/HD RGB 1 IN B/PB VD RGB 2 IN DVI-D IN MENU POWER ON STANDBY VIDEO S-VIDEO
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 29
    DVD player High-vision video deck DVI-D signal DVI-D input module ET-MD77DV PC Projector IN OUT REMOTE 1 REMOTE 2 IN RS-232C IN RS-422 IN SERIAL RS-422 OUT LAN IN OUT VIDEO S-VIDEO IN R/PR G/Y SYNC/HD RGB 1 IN B/PB VD RGB 2 IN DVI-D IN MENU POWER ON STANDBY VIDEO S-VIDEO
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 30
    signal details will appear on the screen momentarily and then disappear automatically. AUTO 480i 576i *1: The LAN terminal of the input module (optional) cannot be used with the PT-D10000U/PT-DW10000U. Use the LAN terminal that is provided as standard with the projector. 30 - ENGLISH
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 31
    . • Use a 5CFB or superior cable for connection to transmit the image information without error. (Example: 5CFB, 5CFTX, 7CFB etc.) *1: The LAN terminal of the input module (optional) cannot be used with the PT-D10000U/PT-DW10000U. Use the LAN terminal that is provided as standard with the projector
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 32
    clock- Note • The DVI-D signal input module supports only a single link. • The HDMI-DVI-D problems may be encountered in operation. *1: The LAN terminal of the input module (optional) cannot be used with the PT-D10000U/PT-DW10000U. Use the LAN terminal that is provided as standard with the projector
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 33
    the dustproof sponge from the lens fitting of the projector before installing the projection lens. (Keep the dust-proof sponge in a safe place for later use if needed.) • After removing the projection lens, install the dust-proof sponge to the lens fitting of the projector in order to stop dust
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 34
    shows the power supply status. Make sure that you fully understand the operation of the power indicator lamp before operating the projector. Indicator status Off Red Lit Green Lit Orange Lit Projector status Main power is off Standby mode POWER ON (|) button can be pressed so that images can
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 35
    When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen. • If the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 36
    power supply will not light up the light source lamp if the lamp is in the process of cooling down after turning off the power supply. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently. • The projector consumes approximately 25 W of power even in standby
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 37
    projector 1. Press LENS on the control panel on the main unit. • Pressing the button changes the setup screen in the order of "FOCUS", "ZOOM" and "SHIFT". 2. Press to select an item and adjust it. LENS FOCUS ɹɹADJUST LENS ZOOM ɹɹADJUST LENS SHIFT ɹɹADJUST ■ Using the remote control 1. Press LENS
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 38
    is to protect the parts of the projector. Using the standard projection position as the reference, the optical axis shift function makes it possible to adjust the projection position in the ranges shown in the figures below. Model number of projection lens PT-D10000U PT-DW10000U 0.15V 0.50V
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 39
    installing the lens. • Tool to be used : Allen hex socket driver or Allen wrench (2.5 mm diagonal hexagon) V bottom Basic Operation The instructions within parentheses and lower portions. Attention • When moving the projector, return the lens to the home position (p. 38), and then tighten the 3
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 40
    on shipment of the projector. MENU Press to new signal is supplied, press MENU on the remote control or operating section of the main unit. signals can be registered. • The signals supporting the installed input module are input and their number. If all the memories are used, the data of the old
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 41
    ENTER. • The data of the signal selected is cleared. Sub memory The projector is provided with a sub memory function to register plural pieces of image adjustment source. Use this function when the user needs adjustment of picture quality such as aspect switching and white balance using the same
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 42
    memory items. • MEMORY NO : A1 (1-2) Sub memory number The place in which address code (A1, A2, ..., H7 and H8) signals are registered Note Restrictions • The maximum sub memory items that can be registered for the projector are 96 including the basic signal. ■ How to erase sub memory The currently
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 43
    AUTO SETUP SHUTTER ASPECT FUNC1 Using the SHUTTER function If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily. 1. Press SHUTTER on the remote control or the main unit
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 44
    In this case, manually adjust the items of "INPUT RESOLUTION", "CLOCK PHASE" and "SHIFT". • For specific signals and long-sideways remote control so that it can be used as an easy shortcut button. Note • Refer to "Setting FUNC1" for details. (p. 73) Displaying the internal test pattern The projector
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 45
    the input signal. 1. Press ASPECT on the remote control. • The setting will change as follows each time ASPECT is pressed. VID AUTO (PRIORITY) S1 AUTO DEFAULT THROUGH VID AUTO 16:9*1 HV FIT 4:3*2 H FIT*2 S4:3*1 *1: PT-D10000U Only *2: PT-DW10000U Only Note • Some aspect ratios may not be
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 46
    desired item. MENU SELECT ENTER SUB MENU • Some menu items may not be valid for certain signal formats applied to the projector. The menu items that cannot be adjusted or used are shown in gray characters, and they cannot be selected. 46 - ENGLISH SUB MENU The sub-menu screen for the selected
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 47
    EDID AUX DVI EDID P IN P FUNC1 OSD POSITION OSD MEMORY ■ OPTION2 (pp. 75-82) SUB MENU item PROJECTOR ID INSTALLATION ALTITUDE DIRECTION OUTPUT RESOLUTION (PT-D10000U only) LAMP SELECT LAMP RELAY RS-232C SYSTEM INFORMATION AIR FILTER CLEANING ADJUST DATE STARTUP LOGO PASSWORD ■ TEST PATTERN (p. 83
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 48
    On-screen menus (continued) Using the menu screens 1. Press MENU. • The "MAIN MENU" appears on the screen. MAIN MENU PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE OPTION1 OPTION2 TEST PATTERN SIGNAL
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 49
    . Switching the picture mode The user can switch to the desired picture mode suitable for the image source and the environment in which this projector is used. 1. Press ▲▼ to select "PICTURE MODE". PICTURE PICTURE MODE CONTRAST BRIGHTNESS COLOR TINT COLOR TEMP. GAMMA SHARPNESS NOISE REDUCTION
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 50
    Operation Adjustment Adjustment range Press ► Increases the brightness Maximum value of the dark (black) parts button. of the screen. 31 Press ◄ button. Reduces the brightness of the dark (black) parts of the screen. Minimum value -31 Adjusting Color This adjusts the depth of the colors
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 51
    31 Minimum value -31 Adjusting the color temperature This is used to adjust the pictures if white areas appear bluish or reddish USER1." • "DEFAULT" cannot be selected when the picture mode has been set to "USER." ■ To further adjust toward the desired white balance 3. Select "USER1" or "USER2"
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 52
    follows each time ◄► is pressed. DEFAULT USER1 USER2 2.5 2.2 Note • Separate software is required to select "USER1" and "USER2". Consult your dealer. • " cannot be selected when the picture mode has been set to "USER". Sharpness setting This adjusts the sharpness of the pictures. 1. Press
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 53
    ) ■ To further adjust the selected compensation amount 3. Select "USER" in step 2. 4. Press ENTER. • The "DYNAMIC IRIS" screen will be displayed. DYNAMIC IRIS AUTO IRIS OFF MANUAL IRIS OFF DYNAMIC GAMMA OFF MENU SELECT CHANGE 5. Use ▲▼ to select the item to be adjusted, and then
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 54
    format" below for details on the system formats which can be selected. 54 - ENGLISH How to change the system format Using the menu screen operation enables the user to make the following changes depending on S-Video / Video input or the currently selected input module. The name of the selected
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 55
    to the types of RGB/YPBPR/DVI-D signals compatible with the projector. (p. 118) To display pictures complying with the sRGB standard DEFAULT 0 OFF OFF AUTO 1 MENU SELECT ADJUST 6. Press DEFAULT on the remote control to restore the factory default. 7. Follow the same procedure (steps 5-6)
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 56
    the position MENU ENTER Shift adjustment This function allows the user to adjust the picture position vertically or horizontally if the position of the image projected on the screen is displaced when the projector is properly positioned against the screen. 1. Press ▲▼ to select "SHIFT
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 57
    it into the panels aspect ratio (4:3 for PT-D10000U and 16:9 for PT-DW10000U). • VID AUTO: The projector identifies the video ID (VID) embedded in the . Be careful of this when selecting the aspect ratio. • If using this projector in places such as cafes or hotels to display programmes for a
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 58
    100% 100% 6. Press ◄► to switch "INTERLOCKED". • The setting will change as follows each time ◄► is pressed. OFF ON • OFF : The "V" and "H" settings are used as the vertical and horizontal zoom ratios respectively. • ON : The zoom ratio is set to the "HV" setting. This allows the pictures to be
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 59
    ": 0). • The adjusted value is reflected in other input signals. • Keystone distortion can be corrected to ±40° of the angle of tilt for the projector against the screen. (The range for the angle of elevation is within ±22° when using a lens with a fixed focal point, and it is within ±28° when
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 60
    How to use ADVANCED MENU MENU ENTER Digital cinema reality Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 61
    devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. 1. Press ▲▼ to select "BLANKING". 0 to 255 vertically and 0 to 700 horizontally. • The adjustment value for the PT-DW10000U can be changed within a range of 0 to 540 vertically and 0 to 960
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 62
    OFF DEFAULT Edge blending adjustment This projector has the function to hide the seams used. • ON: When the tilting inside the unit is to be used for the tilting of the edge blending area. • USER: When a specific tilting is to be used for the tilting of the edge blending area. (Separate software
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 63
    select an item, and press ◄► to adjust the setting. • Once adjustment is complete, press MENU to return to "BRIGHT ADJUST". 14. Press ▲▼ to select the part of "UPPER", "LOWER", "RIGHT", "LEFT". ENGLISH - 63 Basic Operation
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 64
    a function for making the brightening of the BRIGHT level in those areas where the pictures overlap less conspicuous when multi-screens have been configured using edge blending. The optimal point is where, after the BRIGHT INSIDE has been adjusted, the compensation amount is the same for the BRIGHT
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 65
    function cannot be used. Raster position When the whole area where the input picture can be displayed is not used, the picture can move the image upward. Pressing ▼ button will move the image downward. ■ PT-DW10000U When 4:3 pictures are displayed Pressing ► button will move the image to the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 66
    turn a light green. • Menus, setting items, adjustment screens, and control button names will be displayed in the language the user chooses. • The available languages are: English, German (DEUTSCH), French (FRANÇAIS), Spanish (ESPAÑOL), Italian (ITALIANO), Japanese ( ), Chinese ( ), Russian
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 67
    OPTION2 TEST PATTERN SIGNAL LIST NETWORK SECURITY MENU SELECT ENTER SUB MENU Adjusting color matching When multiple sets are used simultaneously, this projector allows the user to correct the difference of colors among the sets. 1. Press ▲▼ to select "COLOR MATCHING". OPTION1 COLOR MATCHING LARGE
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 68
    be carried out by a person who is familiar with the projector or by a service person because a high level of skill is required to make "COLOR TEMP." setting is fixed at "USER1". 68 - ENGLISH Adjusting the color matching using a colorimeter The "R (Red)", "G (Green)", "B (Blue)", "Cy (Cyan)", "Mg
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 69
    6. Use the colorimeter to measure the luminance (Y) and chromaticity coordinates (x, y). 7. Press ▲▼ be set as the target data. • If the target data is outside the color range of the projector, the colors will not be projected correctly. Large Screen Correction If watching images close up on a
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 70
    used at conferences or other venues, the screen display position can be adjusted automatically without having to press AUTO SETUP on the remote ) Use this setting when adjusting a specific or as follows each time ◄► is pressed. DEFAULT WIDE USER • DEFAULT: to receive signals of which image aspect
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 71
    user will be projected in the projection area. • LOGO3: The Panasonic logo is projected. Note • Separate software is required in order to create the pictures to use each time ◄► is pressed. EDID1 EDID2 (PC) • EDID1 (Input signal formats supported) : 480p, 576p, 720/60p, 720/59.94p, 720/50p, 1 080
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 72
    resolution: VGA-UXGA (non-interlace) Dot clock frequency: 25 MHz - 162 MHz Note • Interlace signals are not supported even when the EDID2 (PC) mode is selected. P IN P This item is used to set the condition of the Picture-InPicture. 1. Press ▲▼ to select "P IN P". OPTION1 COLOR MATCHING LARGE
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 73
    menu is not displayed), the ◄► buttons can be used to switch the size and position of the main window and subwindow when the P IN P function is on. Setting FUNC1 The user can specify the function of the "FUNC 1" button on the remote control. 1. Press ▲▼ to select "FUNC1". OPTION1 COLOR MATCHING
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 74
    Option1 settings (continued) Position of on-screen indications The user can specify the position of the on-screen indications. 1. Press ▲▼ to select "OSD POSITION". OPTION1 COLOR MATCHING LARGE SCREEN CORRECTION AUTO SIGNAL AUTO SETUP BACK
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 75
    or separately with a single remote control. The ID number is set to "ALL" by default. Hence the ID number need not be set when only one projector is used. 1. Press ▲▼ to select "PROJECTOR ID". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C SYSTEM INFORMATION
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 76
    the setting by displaying the on-screen indications using buttons of the remote control or the control panel on the main unit. 1. Press ▲▼ to select "INSTALLATION". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C SYSTEM INFORMATION AIR FILTER CLEANING DATE
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 77
    ). Output resolution (PT-D10000U only) Pictures projected onto a screen (for SXGA) with a 5:4 aspect ratio can be displayed with the SXGA resolution. 1. Press ▲▼ to select "OUTPUT RESOLUTION". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION OUTPUT RESOLUTION LAMP SELECT LAMP RELAY RS-232C
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 78
    to one of four brightnesses in accordance with the operating conditions and purpose of use. 1. Press ▲▼ to select "LAMP SELECT". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C 2 FRONT-F LOW H QUAD OFF SYSTEM INFORMATION AIR FILTER CLEANING DATE AND TIME
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 79
    more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use. 1. Press ▲▼ to select "LAMP RELAY". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C SYSTEM
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 80
    SIGNAL 3( 0) MD77DV:DN 1/96 CHANGE Cleaning the air filter This can be used to set air filter cleaning. 1. Press ▲▼ to select "AIR FILTER CLEANING". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C SYSTEM INFORMATION AIR FILTER CLEANING DATE AND TIME STARTUP
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 81
    is in progress. If there is a problem with the air filter, the air filter projector's internal clock. 1. Press ▲▼ to select "DATE AND TIME". OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP item to be set, and use ◄► to set the local time. 8. Use ▲▼ to select "APPLY", and
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 82
    The Panasonic logo and DIGITAL PROJECTOR logo are projected. • OFF: No startup logo is projected. • LOGO1: The picture registered by the user will be projected. • LOGO2: The picture registered by the user will be projected. Note • Separate software is required in order to create the pictures to use
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 83
    of displayed internal test patterns The setting will change as follows each time ◄► is pressed. MENU screen + Focus MENU screen + Entry screen The projector has 8 types of internal test patterns to check the condition of the set. MENU Press to display the MAIN MENU screen. Press to select
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 84
    ENTER to change the setting. NETWORK HOST NAME DHCP IP ADDRESS PORT SUBNET MASK GATEWAY STATUS STORE PROJECTOR OFF 192.168. 0. 8 80 255.255.255. 0 192.168. 0. 1 DEFAULT This allows you to use network functions. MENU Press to display the MAIN MENU screen. Press to select "NETWORK". Press to
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 85
    back to the factory setting The user can return all settings of network function such as IP address, password and E-mail setting to the factory setting. 1. Press ▲▼ to select "STORE". NETWORK HOST NAME DHCP IP ADDRESS PORT SUBNET MASK GATEWAY STATUS STORE PROJECTOR OFF 192.168. 0. 8 80 255.255
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 86
    available in your system. • Use a straight insulated LAN cable which supports category 5 or above. • The length of LAN cable must be 100 m or shorter. ■ Name and function of network function parts LAN terminal (10BASE-T/100BASE-TX) Connect LAN cable here. IN OUT REMOTE 1 REMOTE 2 IN RS-232C IN
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 87
    . 2. Enter the IP address set by the projector into the URL input field of the Web browser. 3. Enter your "User Name" and "Password". • At the time of shipment from the factory, the "User Name" is set to "user1" and the "Password" is set to "panasonic" (lowercase). 4. Press OK and the top page
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 88
    How to use network function (continued) ■ Basic control page This page is the first page displayed when the projector is accessed through a web browser. To move from another page, click [Projector control], then [Basic control]. Control button Click this item, and a projector control page appears.
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 89
    the input switching status. Displays temperature of projector's intake air. Displays temperature inside the projector. Displays temperature of projector exhaust. Displays the lamp lit hours. Displays the type of projector. Displays used hours of the projector. Displays the firmware version of the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 90
    may be that the projector's ventilation holes are blocked. The lamp runtime has exceeded the prescribed cumulative time, and it is now time to replace the lamp. The lamp has failed to light. Wait a short while for the lamp to cool off, and then turn on the power. Trouble has occurred in the contrast
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 91
    With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be sent to one or more preset e-mail addresses (maximum two addresses). Click [Projector Control], then [E-mail set up] to display the E-mail setup page. Select "Enable" to use the E-mail
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 92
    it when the second E-mail address is not going to be used. Select the conditions for sending E-mail. MAIL CONTENTS: Select "NORMAL" or "SIMPLE". ERROR: an error is detected by self-diagnosis. LAMP1 RUNTIME: remaining lamp service time has reached the value set in the field. LAMP2 RUNTIME: remaining
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 93
    Special Features Check these boxes when E-mail is to be sent periodically to two E-mail addresses. E-mail will be sent at the times and on the days checked. Button to update settings ■ DNS server set up page Click [Network set up], then [DNS server set up] to display the DNS server set up page.
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 94
    How to use network page. Select the authentication method specified by your Internet service provider. Set this if SMTP authentication has been selected. Alphanumeric characters (A-Z, a-z, 0-9), hyphen (-), period (.) POP server user name field POP server password field Enter the port number for
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 95
    is sent when an error has occurred. Subject: Panasonic projector report(ERROR) === Panasonic projector report(ERROR) === Projector Type : D10000 .SENSOR [ OK ] BATTERY [ OK ] AIRFLOW SENSOR [ OK ] AC POWER [ OK ] (Error code 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00) Input air
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 96
    . Enter the IP address if DHCP server is not used. Enter the port number here. Number 80 is normally used. Enter the net mask if DHCP server is not used. Enter the gateway address if DHCP server is not used. Enter the name of the projector here. Enter the host name here if it is
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 97
    ■ Firmware update page (The firmware should be updated only by an individual with the specialized knowledge required to do this.) Enter here the filename of the firmware to be updated. After entering the filename, press the [Upload] button. Data transfer is now commenced. It will take several dozen
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 98
    to carry out the following operations from a computer. • Projector settings • Querying the projector status Supported commands The following table lists the PJLink™ protocol commands that can be used to control the projector. Command Control details Notes POWR Power supply control Parameters
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 99
    and text settings can be made after the security screen is displayed. ● If using for the first time 1. Press and ◄ in this order. ● If the correct password is entered, the user will be prohibited from performing any operations apart from POWER STANDBY ( ) and lens adjustments. 1. Press ▲▼ to
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 100
    enabled. • LOGO1: The picture registered by the user will be projected. • LOGO2: The picture registered by the user will be projected. • LOGO3: The Panasonic logo is projected. Note • Separate software is required in order to create the pictures to use for "LOGO1" and "LOGO2". Consult your dealer
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 101
    Changing the text The characters displayed in the text can be changed when "ON" has been selected as the "TEXT DISPLAY" setting. 1. Press ▲▼ to select "TEXT CHANGE". SECURITY PASSWORD OFF PASSWORD CHANGE TEXT DISPLAY OFF TEXT CHANGE MENU SELECT ENTER SUB MENU 2. Press ENTER. • The "TEXT"
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 102
    Using the serial terminals The main unit is equipped with SERIAL terminals located in its connection terminals, and this terminal is compliant with RS-232C/RS-422. Also a serial output terminal is provided to enable plural projector control. Examples of connection ■ For RS-232C ● Single projector
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 103
    IN RS-422 IN SERIAL RS-422 OUT RS-232C IN RS-422 IN SERIAL RS-422 OUT Connection terminals on projector 1 Connection terminals on projector 2 D-Sub 9-pin (male) D-Sub 9-pin (female) D-Sub 9-pin (male) Communication cable (straight) Communication cable (straight) ■ Pin assignments and signal
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 104
    Using projector to the personal computer. • Projector ID supported code is 02 and the "ETX" character code is 03. • If a command is sent with a projector ID specified, the projector will return answer back only in the following cases: If it coincides with the projector ID, ID specification Active lamp
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 105
    ■ Connecting to a PC ● For RS-232C Projector 1 NC 2 3 4 NC 5 6 NC 7 8 9 NC Computer (DTE specifications) NC 1 2 3 NC 4 5 NC 6 7 8 NC 9 ● When multiple projectors are connected 1st (RS-422 OUT) 1 2 3 4 5 6 7 8 9 2nd (RS-422 IN) 1 2 3 4 5 6 7 8 9 Attention • To
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 106
    remote control signal cannot be received. Example of a control panel layout Remote terminal External control Remote terminal/External control STANDBY ON LAMP RGB1 VIDEO Projector following buttons on the projector's control panel and on the remote control cannot be used. POWER button, input
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 107
    for replacing the lamp unit. "REPLACE THE LAMP" • This lamp monitor lights up when the lamp message on the screen unit used hours have reached 1 800 hours. when turning on the Request the dealer to replace the lamp unit. projector power supply? LAMP monitor Blinking in red (3 times) Error is
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 108
    replaced and the metal mesh filter and brush inside the filter unit should be cleaned after approximately 2 000 hours of use, although this is a guide the air filter forwards while removing the filter cleaning unit from the projector. 3. Remove the static electric mesh filter from the filter cleaning
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 109
    . Attention • The air filter must be installed before using the projector. If the projector is used without the air filter installed, foreign particles and dust will get inside the projector and cause problems with operation. Pin guide Filter cleaning unit Static electric mesh filter Filter
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 110
    unit is an optional part. Contact the dealer. Replacement Lamp Unit model No.: ET-LAD10000 (single bulb), ET-LAD1000F (4 bulbs) Rating: 250 W • Other lamps than specified above cannot be used. Be sure to use the specified lamp. Timing of lamp unit replacement The lamp used for the light source has
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 111
    to be replaced until the screws turn freely. Hold the handle of the lamp unit and gently pull the lamp unit out from the projector. Lamp unit cover Fixing screws CAUTION The lamp unit and structural parts around the lamp unit will be hot immediately after the projector has been used. You might
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 112
    a ceiling mount bracket not manufactured by Panasonic, or if damage to the projector occurs as a result of an inappropriate location used for installing the ceiling mount bracket, even if the projector's warranty period has not yet expired. • Use a torque screwdriver or similar tool to tighten the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 113
    a signal that is not compatible with the projector? 119 • Is the cable too long? - • Is the correct signal destination set for notebook computer screen - image? • Use Fn and F3 keys for setting. (For details, refer to the instruction - manual of the computer.) ENGLISH - 113 Information
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 114
    power supply voltage input has dropped. Check that there is sufficient electrical wiring capacity for the projector's power consumption requirements. • Close the lamp unit cover. • The battery needs to be replaced. Consult your dealer. • If turning the main power off and back on again does not clear
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 115
    error Lamp 2 memory error Lamp 3 memory error Lamp 4 memory error FPGA1 configuration error FPGA2 configuration error Flash ROM error RAM error FPGA expansion error Lens shift error Power supply fan error Lamp 1 fan error Lamp 2 fan error Lamp 3 fan error Lamp 4 fan error Ballast circuit 1 fan error
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 116
    Specifications Model No. Power supply Power consumption Amps PT-D10000U PT-DW10000U AC 120 V, 50 Hz/60 Hz 1 500 W (about 25 W in standby) Maximum 15 A Panel size 0.95 inch (aspect ratio 4:3) 0.95 inch (aspect ratio 16:9) DLP® panel Display system Three-unit DLP® chip, DLP® type Number of
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 117
    -SDI input module: ET-MD77SD1 HD/SD-SDI input module: ET-MD77SD3 Replacement Lamp Unit: ET-LAD10000 (single bulb), ET-LAD1000F (4 bulbs) *1 Interlace signals are not supported even when the EDID2 mode is selected. *2 70˝ - 300˝ for ET-D75LE5 *3 If using the projector at high altitudes (1 400
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 118
    specifies the types of RGB/ YPBPR/DVI-D signals compatible with the projector. RGB signals can also be input within the range of fH=15 with 1 400 × 1 050 dots and displayed. • The number of display dots of the PT-DW10000U is 1 920 × 1 080. If signals with a number of display dots differing from the
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 119
    , 1 080/24sF, 1 080/30p, 1 080/25p, 1 080/24p, 1 080/60p, 1 080/50p Note • Noise reduction cannot be used with analog RGB input, DVI input (EDID1 setting) or AUX input (EDID1 setting). • For the PT-DW10000U, the picture quality for the sub window will deteriorate if the size of the main window is 75
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 120
    the hot air coming out from the air outlet vents does not get drawn in through the air intake vents. • When the projector is to be placed inside a box and used, leave the clearances shown in Fig. 2 and ensure that the temperature during operation remains within the 0 °C to 35 °C range. 120 - ENGLISH
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 121
    adjustment ..........62-64 Effective range of remote control operation 17 F Frame delay 64 G Gamma setting 52 H HD/SD-SDI input module 31 How to adjust the lens 37-39 How to install and remove the projection lens 33 I Indication of monitor lamp 107 Installation dimensions diagram .....120
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 122
    does not grant copyrights. Do not reverse engineer, change or modify the software. The guarantee will not be valid for any malfunctions caused by such actions. Trademark Acknowledgement • Digital Light Processing, DLP, and DLP® CHIP are registered trademarks of the Texas Instruments. • VGA and XGA
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 123
    constituer un risque de choc éIectrique aux personnes. Le point d'exclamation dans un triangle avertit l'usager de la présence d'instructions importantes concernant l'utilisation et l'entretien (réparation) dans la littérature accompagnant le produit. ATTENTION: Cet appareil est équipé d'une fiche
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 124
    installer ce projecteur dans un endroit qui n'est pas assez résistant pour supporter le poids du projecteur. • Si l'emplacement d'installation n'est pas assez tout endommagement du cordon d'alimentation. • Contacter un centre de service autorisé pour toute réparation du cordon d'alimentation qui s'
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 125
    incendie ou des chocs électriques. ■ Ne jamais démonter la lampe. • Toute rupture de la lampe risquerait en effet de causer de graves blessures. ■ Ne pas le fil accessoire (à installer à un endroit différent que le support de montage au plafond) ainsi que les oeillets correspondants, en tant
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 126
    é les mains, le visage ou d'autres parties de votre corps très sensibles à la chaleur. ■ Ne jamais réutiliser une lampe usagée. • La lampe risquerait en effet d'exploser. ■ Le remplacement de la lampe ne devrait être effectué qu'après lui avoir laissé le temps de se refroidir, car vous risqueriez de
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 127
    é le gaz, ou que le gaz a pénétré dans les yeux ou la bouche, consulter immédiatement un médecin. • Demander à son revendeur de remplacer l'unité de lampe et de vérifier l'intérieur du projecteur. ■ Demander à un centre technique agréé de nettoyer l'intérieur du projecteur au moins une fois par an
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 128
    sont bien compris avec votre projecteur. Télécommande [N2QAYB000076 × 1] Piles de la télécommande (AA) Cordon d'alimentation [K2CG3YY00015 x 1] Support anti-chutes Oeillet [THEA172J × 4] Fil [TTRA0144 × 4] Mise en garde concernant les déplacements du projecteur L'objectif de projection est
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 129
    subies pendant son utilisation. ● La durée de vie d'une lampe au mercure dépend fortement des conditions d'utilisation auxquelles elle est huile. Si vous désirez utiliser un produit chimique, veuillez suivre les instructions fournies. ● Ne jamais nettoyer la surface de l'objectif avec un linge
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 130
    soumise à de très fortes pressions internes. Une mauvaise manipulation risquerait d'entraîner une défaillance. • Une lampe usée risque même d'exploser en cas de manipulation violente. Contacter un prestataire de services spécialisé dans le traitement de déchets industriels pour la mise au rebut des
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 131
    par sa poignée, continuer à tirer dessus jusqu'à l'extraire complètement du projecteur. Vis du couvercle de la lampe Couvercle de la lampe Vis de fixation Poignée MISE EN GARDE La lampe ainsi que les pièces se trouvant à proximité sont toujours extrêmement chaudes juste après l'utilisation du
  • Panasonic PT-DW100U | Dlp Projector - Multi Language - Page 132
    Panasonic Projector Systems Company Unit of Panasonic North America One Panasonic Way 4B-9 Secaucus, NJ 07094 (201) 392-6591 3330 Cahuenga Blvd West Los Angels, CA 90068 (323) 436-3500 Technical Support: (800) 524-1448 (800) 526-6610 FAX: (201) 392-6514 E-Mail: [email protected] Panasonic
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
TQBJ 0208
Operating Instructions
DLP
®
Based Projector
Commercial Use
PT-D10000U
PT-DW10000U
Read these instructions completely before operating this unit.
Models No.