Panasonic SABT100 Blu-ray Dvd Home Theater Sound System - Page 39
Troubleshooting guide
View all Panasonic SABT100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to "Customer Services Directory" on page 46 if you reside in the U.S.A., or refer to "Product information" on page 47 if you reside in Canada. The following do not indicate a problem with this unit: ≥Regular disc rotating sounds. ≥Image disturbance during search. To reset this unit To restore the unit if it freezes due to one of the safety devices being activated To return all settings other than some settings to the factory preset To return to the factory preset ≥Press and hold [POWER Í/I] on the main unit for 10 seconds. (The settings remain unchanged.) ≥Select "Yes" in "Restore Default Settings" in the Setup menu. This returns all values in the Setup menu and the on-screen menu, except for "Remote Control Code", "On-screen Language", "DVD-Video Ratings", "BD-Video Ratings" and "Speaker" to the default settings. ≥Reset the unit as follows: 1 Press [POWER Í/I] on the unit to turn off the unit. 2 Press and hold [9/5], [∫] and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds until "PLEASE WAIT" is displayed on the unit. 3 The power is turned off automatically. Page - 32 - Power No power. ≥Insert the AC power supply cord securely into a known active AC outlet. 8 The unit switches to standby ≥This is a power saving feature. It can be changed if desired using "Off Timer" in the Setup 32 mode. menu. ≥When the time set for the sleep timer has passed, the power will be turned off. 16 ≥One of the unit's safety devices is activated. Press [POWER Í/I] on the main unit to turn the - unit on. Operation The remote control doesn't work properly. The unit is on but cannot be operated. Play fails to start even when [1] (PLAY) is pressed. Play starts but then stops immediately. Cannot eject disc. Startup is slow. When the unit is turned on, audio and video output takes a long time. Cannot set "On" in "BD-Video 24p Output". ≥The remote control and main unit are using different codes. Change the code on the remote control. Press and hold [OK] and the indicated number button at the same time for more than 5 seconds. ≥The batteries are depleted. Replace them with new ones. ≥You are not pointing the remote control at the main unit's remote control signal sensor during operation. ≥Colored glass may obstruct the signal reception/transmission. ≥Don't place the signal sensor in direct sunlight or in areas that may be subject to sunlight exposure. ≥It may be necessary to set the code on the remote control again after changing the batteries. ≥Confirm the correct source is selected. ≥Some operations may be prohibited by the disc. ≥The unit is hot ("U59" appears on the display). Wait for "U59" to disappear. ≥One of the unit's safety devices may have been activated. Reset the unit as follows: 1 Press [POWER Í/I] on the main unit to switch the unit to standby. If the unit doesn't switch to standby, press and hold [POWER Í/I] on the main unit for about 10 seconds. Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it. 2 Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the dealer. ≥Condensation has formed: Wait 1 to 2 hours for it to evaporate. ≥Insert the disc correctly with the label facing up. ≥The disc is dirty. ≥You tried to play a blank disc or unplayable disc on this unit. ≥The producers of the disc can control how discs are played. So you may not always be able to control play as described in these operating instructions. Read the disc's instructions carefully. ≥The unit may have a problem. While the unit is off, press and hold [:/6] and [< OPEN/CLOSE] on the main unit at the same time for about 5 seconds. Remove the disc and consult the dealer. ≥Startup takes time in the following situations. - Immediately after a power failure or the AC power supply cord is connected. - When the unit is connected with an HDMI cable. ≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p can you select "On". 42 3 3 - - 42 10 - 38 - - 14 42 12, 13 - - - 33 Reference Displays The display is dim. The elapsed time displayed is actually less than the playtime. ≥Change "FL Display" in the Setup menu. ≥The displayed play time is converted from the number of frames at 29.97 frames (equal to 0.999 seconds) to one second. There will be a slight difference between the time displayed and the actual elapsed time (e.g., actual one-hour elapsed time may display as approximately 59 minutes 56 seconds). 33 - RQT9129 39