Panasonic SAHT930 Dvd Theater Receiver - Page 31
Other useful functions
View all Panasonic SAHT930 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
SUBWOOFER LEVEL Subwoofer level You can adjust the amount of bass. The unit automatically selects the most suitable setting according to the type of playing source. Press [SUBWOOFER LEVEL]. ≥When DVD-Video or DVD-RAM is selected SUB W 4 (factory preset)>SUB W 1>SUB W 2>SUB W 3 When another source is selected SUB W 2 (factory preset)>SUB W 3>SUB W 4>SUB W 1 DIGITAL DISC TUNED T G S.SRND D.MIX SLP PL DTS CD MODE RDS PS PTY W DVD RAM MONO STCT LCR LS RS S LFE RND 12 PGM PRG H.BASS The setting you make is retained, and recalled every time you play the same type of source. SHIFT TEST CH SELECT Speaker level adjustments This is one of the ways to get appropriate surround effects. Preparation Press [DVD/CD]. 1 While stopped and no on-screen display is shown Press [SHIFT]i[TEST] to output a test signal. L: Front left C: Center R: Front right RS: Right surround LS: Left surround ≥There is no output from SW (subwoofer) channel. 2 Press [VOLUME, r] or [s] to set the volume level normally used for listening. 3 Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker. C, RS, LS: `6 dB to i6 dB (L, R: Only the balance is adjustable.) ≥To adjust the balance of the front speakers While outputting the test signal, press [2, 1]. ≥Adjust the speaker level to the same level as the front speakers. To stop the test signal Press [SHIFT]i[TEST] again. ∫ To adjust speaker level during play (Effective when playing multi-channel audio or when Dolby Pro Logic II or Super Surround is on.) 1 Press [CH SELECT] to select the speaker. L #C #R #RS #LS #SW SW: Subwoofer ≥You can adjust SW only if the disc includes a subwoofer channel. ≥"SW" does not appear on the display and is not adjustable when Dolby Pro Logic II is turned on. ≥"S" appears on the display when "MUSIC" or "MOVIE" is selected with Super Surround (➜ page 30). In this case, you can adjust both surround speaker levels at the same time using [3, 4]. S: `6 dB to i6 dB 2 Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker. C, RS, LS, SW: `6 dB to i6 dB (L, R: Only the balance is adjustable.) ≥To adjust the balance of the front speakers While "L" or "R" is selected, press [2, 1]. Sound field and sound quality/Other useful functions Other useful functions Sleep timer SHIFT SLEEP QUICK OSD Press [SHIFT]i[SLEEP] to select the time (in minutes). SLEEP 30_----)SLEEP 60_----)SLEEP 90 ^""""" OFF(_ SLEEP 120(__} D.MIX SLP To cancel the timer Press [SHIFT]i[SLEEP] to select "OFF". To confirm the remaining time Press [SHIFT]i[SLEEP] again. To change the setting Repeat the procedure from the beginning. SETUP MUTING Muting Press [MUTING]. "MUTING" flashes on the unit's display. DIGITAL DISC TUNED T G S.SRND D.MIX SLP PL DTS CD MODE RDS PS PTY W DVD RAM MONO STCT LCR LS RS S LFE RND 12 PGM PRG H.BASS To cancel ≥Press [MUTING] again or reduce the volume to minimum (- - dB), then raise it to the required level. ≥Muting is canceled when you switch the unit to standby. Using headphones Main unit only 1 Reduce the volume and connect the headphones (not included). Headphone plug type: 3.5 mm (1/8z) stereo VOLUME OPEN CLOSE DISC EXCHANGE DISC SKIP POWER INPUT 1 2 3 4 5 SELECTOR 5 DISC SELECTOR H.BASS PROGRESSIVE CD MODE TUNE MODE FM MODE MEMORY VOLUME TUNING DOWN PHONES UP 2 Adjust headphone volume with [VOLUME]. ≥Audio is automatically switched to stereo (2-channel). [Note] Avoid listening for prolonged periods of time to prevent hearing damage. RQT7972 31