Pfaff 1246 Owner's Manual

Pfaff 1246 Manual

Get Pfaff 1246 PDF manuals and user guides View all Pfaff 1246 manuals
Add to My Manuals
Save this manual to your list of manuals

Pfaff 1246 manual content summary:

  • Pfaff 1246 | Owner's Manual - Page 1
    1245 1246 Instruction manual 2962-17 841 Betriebsanleitung engi. 10.97
  • Pfaff 1246 | Owner's Manual - Page 2
    This Instruction manual is valid for all models and subclasses listed in the chapter ,,Specifications". The reprintng, copying or translation of PFAF Instruction Manuals, whether in whole or in part, is only permitted with our previous permission and with written reference to the source. G.M. PFAFF
  • Pfaff 1246 | Owner's Manual - Page 3
    subclass -91 0/01> Pedal (on machines with automatic presser-foot lifter (subclass -910/98) Key on the machine head (for machines with backtacking mechanism -91 1/97) Lever for lifting the presser foot Feed regulator / reverse sewing Feed regulator on machines with backtacking mechanism -91 1/97
  • Pfaff 1246 | Owner's Manual - Page 4
    Mounting the spool holder Mounting the sewing lamp Commissioning the machine Switching the machine on/off Preparation Inserting the needle in the PFAFF 1245 Inserting the needle in the PFAFF 1246 Winding the bobbin thread, adjusting the thread tension Removing/Threading the bobbin case Inserting the
  • Pfaff 1246 | Owner's Manual - Page 5
    -feed stroke Lifting motion of the top feed Bobbin-case opener Safetyclutch Needle thread tension release Thread check spring Thread check spring on PFAFF 1246 with thread trimmer -900/56 Bobbin winder Presser-foot pressure 11 .05 Adjusting the thread trimmer -900/56 11 .05.01 11.05.02 11 .05.03
  • Pfaff 1246 | Owner's Manual - Page 6
    be used for the purpose for which it is intended and may not be operated without its safety devices. All safety regulations relevant to its operation are to be adhered to. • When exchanging sewing tools (e.g. needle, presser foot, needle plate, feed dog or bobbin), when threading the machine, when
  • Pfaff 1246 | Owner's Manual - Page 7
    Instruction Manual is a component part of the machine and must be available to the operating personnel at all times. • The Instruction Manual must be read before operating the machine persons operate and work on the machine. Further information can be obtained at your PFAFF agent. 'FAFF 1-2
  • Pfaff 1246 | Owner's Manual - Page 8
    equpping, operating and cleaning of the machine as well as taking care of faults arising in the sewing area. The operating personnel is obliged to observe the following points and must: • always observe the Notes on Safety in the Instruction Manual! • never use any working methods which could limit
  • Pfaff 1246 | Owner's Manual - Page 9
    so that it is always easily accessible. I," A I," Never reach into the sewing area while sewing! Danger of injury by the needle! Never leave objects on the table or in the needle plate area while adjusting the machine settings! Objects can become trapped or be slung away! Danger of injury
  • Pfaff 1246 | Owner's Manual - Page 10
    Safety Do not operate the machine without tilt-back safeguard 3! Danger of crushing between upper part and table top! 4 A Do not operate the machine I-" without belt guards 4 and 5! Danger of injury by the revolving V-belt! 1-03 1-5 PFAFF
  • Pfaff 1246 | Owner's Manual - Page 11
    use 2 Proper use PFAFF 1245 The PFAFF 1245 is a single needle, flatbed sewing machine with bottom, top and needle feeds as well as a large vertical hook for sewing lockstitch seams. The machine is designed for commercial use (industry). PFAFF 1246 The Pfaff 1246 is a two-needle, flat bed sewing
  • Pfaff 1246 | Owner's Manual - Page 12
    PFAFF 1245 Stitch type: Needle system Needle thickness in 1/100 mm: ModeIC' Max. thread thickness (synthetic A): Model C: Max. stitch length: Model N Model N8 Handwheel eff. dia.: Max. speed 301 (!ockstitch) 134-35 110-140 20/3 6.0 mm 8.0 mm 80 mm see chapter 3.03 Dimensions of machine: Length
  • Pfaff 1246 | Owner's Manual - Page 13
    3.03 Max. number of s1 titches/min Specifications Top feed lift less than 3.5 mm from 3.5 to 5.5 mm from 5.5 to 7 mm Max. number of stitches/min' for stitch lengths up to 6 mm Max. number of s1 titches/mirr for stitch lengths from 6 mm to 8 mm 2800 2500 2000 2600 2500 2000 3-2 PFAFF
  • Pfaff 1246 | Owner's Manual - Page 14
    Specifications 3o4 PFAFF 1246 Stitch type Needle system: Needle thickness in 1/1 00 mm: ModeIB ModelC Max. thread thickness (synthetic'): Model B Model C Max. stitch length: Model BN and CN Model CN8 Handwheel eff. dia Max. speed Dimensions of machine: Length Width Height Clearance width:
  • Pfaff 1246 | Owner's Manual - Page 15
    n1 x - 3 3 () - C (71 - D Top feed lift 0 S" b-i CD 0, 3 0 -4-. 3 Cl) C, Max, number of stitches/mm for N) N) CD (I) (aa0 aa aa stitch lengths up to 6 mm and needle gauge of up to 10 mm Max. number of stitches/mm for - N) N) aa Naa) a(71 stitch lengths up to 6 mm and
  • Pfaff 1246 | Owner's Manual - Page 16
    waste is the responsibility of the customer. • The materials used on the machines are steel, aluminium, brass and various plastics. The electrical equipment consists of plastics and copper. • The machine waste is to be disposed of in accordance with the locally valid environmental protection
  • Pfaff 1246 | Owner's Manual - Page 17
    of the customer. 5.04 Storage The machine can be stored for up to 6 months if not in use. During this time it should be protected from dust and moisture. For longer storage the individual parts of the machine, especially the moving parts, should be protected against corrosion e.g. by
  • Pfaff 1246 | Owner's Manual - Page 18
    in the following section of this Instruction Manual, certain tasks or important pieces of information are accentuated by symbols. The symbols used have the following meanings: Note, information Cleaning, care Lubrication, greasing Servicing, repairing, adjustment, maintenance (only to be
  • Pfaff 1246 | Owner's Manual - Page 19
    with Quick motors. When other motors are used, the switch may not look the same. Fi 7O1 7.02 Pedals (on machines with subclas -910/01) With the on/off switch on 0 Machine stop +1 = Sew 1- = Trim thread (on machines with thread trimmer) +2 0 +2 = Raise presserfoot +1 -1 Fg. 7-02 FAFF
  • Pfaff 1246 | Owner's Manual - Page 20
    7.03 Pedal (on machines with automatic presser-foot lifter -910/98) 0 1 With the on/off switch on 0 = Machine stop +1 = Sew 1- = Raise presserfoot 2 - = Trim thread (on machines with threac trimmer) -1 -2 Fiq 7-03 7.04 Key on the machine head (for machines with backtacking mechanism
  • Pfaff 1246 | Owner's Manual - Page 21
    Controls 7.05 Lever for lifting the presser foot • The sewing foot can be lifted by raising even. 1 Fig. 7 05 7.06 Feed regulator / reverse sewing • Adjust the stitch length by turning the knurled nut 1 accordingly. Reverse sewing • Press knurled nut 1 upwards as far as possible lposition
  • Pfaff 1246 | Owner's Manual - Page 22
    options for setting the automatic start and end bartack are to be found in the instructior .1 manual of the motor. Fig. 7 O7 7.08 Adjustment nut for the top-feed stroke Turn the machine off! • Open cover 1 on the back of the machine, loosen screw 2 and move as required. 7-4 Fig. 7 08 PFAI
  • Pfaff 1246 | Owner's Manual - Page 23
    to use can hold the weight of the machine and the motor, even while sewing. 8.01 Mounting The necessary electricity and compressed air supplies must be available at the machine's location with chain 3. (This adjustment is not necessary on machines with an automatic presser-foot lifter) 8-1
  • Pfaff 1246 | Owner's Manual - Page 24
    and commissioning the machine 8.01.02 Adjusting the V-belt tension • Loosen nuts 1. • Tighten the V-belt with belt take-up hanger 2. • Tighten nuts 1. Fig. 8 02 Fig. 8 - 02 shows a Quick motor. If another motor is used, proceed as describE in the motor's instruction manual. 8.01.03 Mounting
  • Pfaff 1246 | Owner's Manual - Page 25
    in the motor's instruction manual. 8.0105 Mounting tilt-over safeguard • Screw-mount tilt-over safeguard 1 included in the accessories with screw 2. - A I,\ Do not operate the machine without tilt-over safeguard 1! Danger of crushing between upper part and table top! PFAFF 1 Fg8-06 8-3
  • Pfaff 1246 | Owner's Manual - Page 26
    Mounting and commissioning the machine 80106 Mounting the spool holder • Mount the spool holder as shown in 0 (1 Rg.8-05. • Insert spool holder in the table-top hole it by means of the included u Fg8-O5 8.0107 Mounting the sewing lampA • Screw the sewing lamp onto the table top (wood
  • Pfaff 1246 | Owner's Manual - Page 27
    hoses for any damage. • Remove pin 1 of the oil reservoir 2 (Fig. S - 06). The pin serves only to protect the machine from damage during transport and must not be used when sewing. • Clean the machine thoroughly and oil it (see chapter 10 Care and maintenance) • Have specialists ensure that the
  • Pfaff 1246 | Owner's Manual - Page 28
    PFAFF 1245 /.\ Turn the machine off! Use only system 134-35 needles! • Loosen needle retaining screw 1. • Insert the needle as far as possible (the long needle-groove must be facing left>. • lighten needle retaining screw 1. The selection of the correct needle depends on the model of the machine
  • Pfaff 1246 | Owner's Manual - Page 29
    the needle in the PFAFF 1246 Preparation Turn the machine off! Use only system 134-35 needles! • Loosen needle retaining screws 1. • Insert needles as far as it will go (the longitudinal needle groove of the left-hand needle must be pointing to the right and that of the right-hand needle to
  • Pfaff 1246 | Owner's Manual - Page 30
    9.03 Winding the bobbin thread, adjusting the thread tension • Place an empty bobbin 1 onto bobbin shaft 2. • Thread the bobbin in accordance with spindle 2 and lever 3. The bobbin fills up while you are sewing. • The tension of the thread on bobbin 1 can be adjusted with knurled screw 4. • The
  • Pfaff 1246 | Owner's Manual - Page 31
    place. • Close latch 1 and close the bed slide. 9.05 PFAFF Inserting the bobbin case / Adjusting the bobbin thread tension A / \ Turn the machine off! Threading the bobbin case. • Thread the bobbin as shown in Fig. 9 - 04. • When the thread is pulled, the bobbin must rotate in the direction of the
  • Pfaff 1246 | Owner's Manual - Page 32
    Preparation 9.06 Threading the needle thread I Adjusting the needle thread tension in the PFAFF 1245 Turnthemachineoff! • Thread the machine as shown in Fig. 9 - 05. Take note that the needle is threaded from • the left (see arrow). Adjust the needle thread tension by turning knuled screws
  • Pfaff 1246 | Owner's Manual - Page 33
    9.07 Threading the needle thread / Adjusting the needle thread tension in the PFAFF 1246 + - Fig. 9 - 06 - - Maschine ausschalten! • Thread the machine as shown in Fig. 9 - 06. Care must be taken that the left-hand needle is threaded from the right and the right-hand needle is threaded from
  • Pfaff 1246 | Owner's Manual - Page 34
    Servicing and maintenance intervals Check the air pressure Clean the hook compartment Check the water container of the air filter General lubrication Lubricate the front parts horn 5 meshes in the groove of the needle plate (see arrow). • Finally, screw hook gib 1 back on. • Insert the
  • Pfaff 1246 | Owner's Manual - Page 35
    _ _ _ 10.03 General lubrication _ Care and maintenance - ooo© - -IL_ e Fig. OO2 A Only use oil with a mean viscosity of 22.0 m 2 /s m at 40°C and a density of 0.865 g3 /cm at 15°C. We recommend PFAFF sewing machine oil. Part no. 280-1 -1 20 144. O PFAFF Fig O-O3 10 - 2
  • Pfaff 1246 | Owner's Manual - Page 36
    all bearings marked in Fig. 10.03 twice a week. Setting the machine upright • Hold the machine, press tilt safety device 3 (Fig. 10-04) and return the machine to an upright position with both hands. Danger of crushing between machine and table top! 10.04 Lubricating the hook 10 - 3 Turn the
  • Pfaff 1246 | Owner's Manual - Page 37
    marked in Fig. 10- 05 twice a week. • Screw the face plate back on. Only use oil with a mean viscosity of 22.0 m 2 /s m at 40°C and a density of 0.865 g3 /cm at 15°C. We recommend PFAFF sewing machine oil. Part no. 280-1-1 20 144. 10.06 Lubricating the top-feed drive excentric Fig 1OO6 Turn
  • Pfaff 1246 | Owner's Manual - Page 38
    pressure 1 Fig. 10-07 • Before each use of the machine, check the air pressure on gauge 1 • I Cleaning the water container of the air filter Turn the machine off! 'V Remove the compressed-air hose from the air filter with isopropyl alcohol, Part number 95-665 735-91. • Screw filter 2 back in and
  • Pfaff 1246 | Owner's Manual - Page 39
    show the PFAFF 1245 single-needle machine. Fttwhoerictrehe,esip rule, (Part No. 08-880 218-00) • Adjustment gauge, (Part No. 08-880 136-14) • Adjustable clamp, (Part No. 08-880 137-00) • Gauge, (top feed stroke 7mm) (Part No.61-111 630-14) • Needles, system 134-35 • Sewing thread and test material
  • Pfaff 1246 | Owner's Manual - Page 40
    Adjustment 11.04 11 .ot.oi Adjusting the basic machine Positioning the feed dog across the direction of sewing Requirement The bottom feed dog must be the same distance from the left and right side of the needle- plate cutout. .4 1 11 - 2 41 Fg. 11 -O • • Loosen screws 1 and
  • Pfaff 1246 | Owner's Manual - Page 41
    Positioning the feed dog in the direction of sewing WRaneidtqhuthtihereebmlaoecnkngtwesitthstrietcshpescett,tothtehebonteteodmlef-epeladtedocgutomuutswt hhaevnefetheedisnagmbeothk ti .iiJ backwards. Adlust rock shaft 1 in accordance with the requirement and tighten screws 2. PFAFF 11 - 3
  • Pfaff 1246 | Owner's Manual - Page 42
    dog must protrude over the needle plate Fig. 11 -03 • • • SBAerditnjusgtsitttchfheeelbedontgdttoohgmc0fa"ereriderd1og(stcoreitws sTD2)Cinbyactcuornridnagnctheewhiathndthwehereeql,uirement. If required, the feed dog height can be reduced a little on machines without a bottom feed lifting phase
  • Pfaff 1246 | Owner's Manual - Page 43
    11 .04.04 P re-adjusting the need)e height Requirement With the needle bar at BDC, the distance between the needle bar and the needle plate must be 15mm. Fig. 11 -04 • Move needle bar 1 (screw 2) in accordance with the requirement without moving it laterally. PFAFF 11 - 5
  • Pfaff 1246 | Owner's Manual - Page 44
    the middle. 11 6 - t7 6 L7i r iKz () I . 05 • Unscrew vibrating presser 1 and presser foot 2. • Set stitch length ,,0" and bring the needle bar to its TDC. • Insert a new needle. Loosen screws 3, 4, 5 and 6. • Position the needle directly over the bottom feed dog by turning the handwheel. • Move
  • Pfaff 1246 | Owner's Manual - Page 45
    dog This adjustment does not apply for machines without a bottom feed lifting phase fiascteuronfetdh.e Fig. 1106 • Bring the needle bar to its BDC. • • Turn with difficulty. • Turn feed lifting eccentric 1 a little further in accordance with requirement 2. • lighten both screws 2. PFAFF 11 - 7
  • Pfaff 1246 | Owner's Manual - Page 46
    and top feeds Requirement With the longest stitch length set and the needle bar at its BDC, the top and bottom feeds should not move driving eccentric 2 can be turned on the shaft with difficulty. • Bring the needle bar to its BDC, • Turn the feed driving eccentric 2 so that its eccentricity
  • Pfaff 1246 | Owner's Manual - Page 47
    11 .04.08 Hook-to-needle clearance, needle rise, needle height and needle guard (On Model 1246 make these adjustments on both sewing hooks.) Requirement With the stitch length set at ,,3' and bar on model ,,B' and 2.0mm after the needle rise at (1.8mm BDC of the needle bar on after BDC of the
  • Pfaff 1246 | Owner's Manual - Page 48
    , tighten On machines with screws 2. automatic thread trimmer -900/56, bring retaining collar 6 to rest on • • bAAeldvigjeunlstpntienheiedonlnee5egadunlaedrdhtie7gihginthetancincsocarrcdecwaonrsdcea3n.wceithwritehqureirqeumireenmte3n. t 2 (see also chapter 11.04.04). Bei der PFAFF 1246
  • Pfaff 1246 | Owner's Manual - Page 49
    Fig. 11 .9 • Set the largest top-feed stroke and the stitch length at ,0". • Bring presser foot 1 to rest on the needle plate. • Turn the handwheel in the direction of rotation until vibrating presser foot 2 has reached its highest point. • Turn crank 3 (screws 4) in accordance with the requirement
  • Pfaff 1246 | Owner's Manual - Page 50
    When presser foot point of the needle 1 is resting on the needle plate, the must both reach the needle plate at vibrating presser foot the same time • • • Allow presser foot 1 to rest Loosen screws 2 until feed Turn feed lifting eccentric 3 on the needle plate. lifting eccentric 3 can
  • Pfaff 1246 | Owner's Manual - Page 51
    3 nor may it be clamped between projection 4 and the retaining trip of the needle plate (see arrows). Fig. 1 1 . 1 1 • Thread the machine, insert test material and allow the presser foot to rest on the needle plate. • Sew a few stitches by turning the handwheel and carry out a check in accordance
  • Pfaff 1246 | Owner's Manual - Page 52
    TIAfhtdeheessactfhreirpteytaiodcnlujatocmfhsh,iostwhseettosbasyfneatthpyetchmlueatccnhluuftsacnhcatpubsraecorkuatinntdofosplclroreewvwes.snt5daarme asgeealetod.the hook. 5 Fig. 11 -12 • • Remove the jammed thread. Press piston 1 and turn the handwheel until hook 3 of pawl 2 clicks into
  • Pfaff 1246 | Owner's Manual - Page 53
    .13 Needle thread tension release Requirement With the presser foot raised, both of the tension discs must be at least 0.5 mm apart. The clearance of 0.5 mm is a minimum and can increase to more than 1 mm when using thick threads. 2 0.5 mm FAFF Fig. 11 -13 • Align pressure plate
  • Pfaff 1246 | Owner's Manual - Page 54
    vary a di little in either direction. 11 - 16 Fig. 11 .14 • Thread the machine, place test material under the presser foot and allow the presser foot to rest on the fabric using the presser foot lifter. • • • Loosen screw 1 Sew a few stitches by turning the handwheel and Continue to turn the
  • Pfaff 1246 | Owner's Manual - Page 55
    .04.15 Thread check spring on PFAFF 1246 with thread trimmer 9OO/56 Requirement The motion of thread controller springs penetrates the material (= about 7 mm 1 and 6 should cease spring deflection). as soon as the needle point Due to technical reasons, the length of the thread-check spring
  • Pfaff 1246 | Owner's Manual - Page 56
    1 mm from the edge of the bobbin. 2 15 Fig. 11 .15 • • Move Place drive wheel a bobbin on 1 (screws 2) in accordance with requirement 1. the bobbin winder, thread the bobbin and switch on the bobbin winder. • Move stop latch 3 (screws 4) in accordance with requirement 2. 11 - 18 PFAFI
  • Pfaff 1246 | Owner's Manual - Page 57
    Adjustment 11.o4.17 Presser-foot pressure Requirement The material must be fed reliably even at top sewing-speed. There mustn't be pressure marks on the material. 1 Fig. 11 -16 • Turn screw 1 in accordance with the requirement. FAFF 11 - 19
  • Pfaff 1246 | Owner's Manual - Page 58
    djustmen t 11.05 11 0501 Adjusting the thread trimmer -900/56 Pre-adjusting the control cam R21.. eTbWqheeauitrhieincetgchneesnutttrarfikacec-beuep( secnretw2,s care to In this note that it is touching retaining position, tighten the four screws collar 7. on control cam 5. 6. taking PFAFf
  • Pfaff 1246 | Owner's Manual - Page 59
    cam 7 when activating lever 8 is activated. ° 7\N F9 ,i 11-18 • Screw out screw 1 and swing out connecting rod 2. • Loosen screws 3 and 4. • Bring the needle bar to needle rise position by turning the handwheel. • Bring clamp 5 to rest on the right side of the housing. • Keeping this position, move
  • Pfaff 1246 | Owner's Manual - Page 60
    -19 • Position the largest eccentricity of bearing surface 1 underneath pawl 2 by turning the handwheel. • Move bearing bolt 3 (screw 4) in accordance with the requirement. 11 22 PFAFF
  • Pfaff 1246 | Owner's Manual - Page 61
    mm between engaging lever 2 and pawl 3. 0 3 1 Fig. 11 . 20 • Bring the machine to needle rise position by turning the handwheel. • Loosen screw 1 until the engaging solenoid can be turned with difficulty. • Manually activate engaging lever 2 so that pawl 3 engages. • Press magneto inductor 4 as
  • Pfaff 1246 | Owner's Manual - Page 62
    , dthtehree must be a base of the distance of cam track. 6 11-24 \ -\ ((C(61AO iA'\ I \3 1 Fig. 11 -21 • • • Bring the machine to needle rise Manually activate engaging lever Taking care to ensure that screw position by turning the handwheel. 1 so that pawl 2 engages. 3 is still loose
  • Pfaff 1246 | Owner's Manual - Page 63
    with control between bolt 4 lever 3 and the at starting position, there outer diameter of control must be cam 5. a Fig. 1 1 - 22 • Bring the needle bar to TDC by turning the handwheel. • Turn screw 1 (nut 2) in accordance with the requirement. • Carry out a check by tapping control lever 3. FF
  • Pfaff 1246 | Owner's Manual - Page 64
    lift from stop 7. 11 - 26 Fig. 11 23 • Affix spherical head 1 to control lever 3 using screw 2. • • Loosen nuts 4 (right and left Bring the machine to needle handed thread). rise position by turning the handwheel and activate • engaging lever 5. Taking care to ensure that lever
  • Pfaff 1246 | Owner's Manual - Page 65
    11 .05.08 Final adjustment of the control cam Requirement When control lever 3 is engaged and the needle point is 12 mm above the needle plate coming from its BDC, the motion of the thread catcher 5 must begin. /Th\ 3 cW I 4-'N Jc / FAFF Fg 1124 • Bring the take-up lever to just past
  • Pfaff 1246 | Owner's Manual - Page 66
    catch 1 and control in resting lever 6. position, there must be a distance of approx. 5 mm Fig. 1 1 25 • • Lightly affix catch 1 and cover plate 2 using screws 3. Move catch 1 as far as possible in the direction of the arrow and then move it laterally in accordance with the
  • Pfaff 1246 | Owner's Manual - Page 67
    Adjustment 11.05,10 Connecting rod (for PFAFF 1246 only) rquirement When the cutting device is in the off-position, the length of spacer rod 4 should be equal to the distance between shafts 2 and 3. X 1 4
  • Pfaff 1246 | Owner's Manual - Page 68
    Adjustment 11.05.11 Thread-catcher height (On Mode' 1246 make these adjustments on both thread catchers.> Requirement When thread catcher 2 is lower point of the thread pushed catcher forwards manually with the take-up ever at must pass 1 mm over the back of hook 4. its TDC, the I M) °2 0
  • Pfaff 1246 | Owner's Manual - Page 69
    point of needle catcher 4 protrudes approx. 3 mm over the cutting edge of the knife, knife 3 must just touch thread catcher 4. thread catcher 4, • Taking care to ensure that screw 1 is loosened, manually turn thread catcher 4 in accordance with requirement 2. • Bring knife 3 to rest against thread
  • Pfaff 1246 | Owner's Manual - Page 70
    1246 make position these adjustments on both thread catchers.) RAcutettqthiuneigrferemodngetenptoofinktnoiffere4v(esresea)aorrfotwh)r.ead catcher 3, its rear edge must be flush with the J© 11-32 Fig. 11 -28 • • • Taking care to ensure that screw 1 is loosened, bring the machine to needle
  • Pfaff 1246 | Owner's Manual - Page 71
    - LI • w L M9JDS UOj Aeid euoziioq ou si eJaq jnsue O OJD bu jei pu uoiisod S!q U wewsnipy
  • Pfaff 1246 | Owner's Manual - Page 72
    thread clamp spring (On Model 1246 make these adjustments on both clamp springs.) Requirement 1. Between clamp spring S and the bottom of thread range and parallel to the bedplate of the machine. • Unhook spring 3, • • Manually pivot thread catcher 4 over clamp spring 5. Bend clamp
  • Pfaff 1246 | Owner's Manual - Page 73
    ____ I V6-U 6i g pue sMajs ue1lb! ejdpq • euiqw eq o telleJ9d si L J81JJeD eq einsue O JD 6UDf pu UO!!SOd siq u heM se ( sMais) L JJJD esseeu ! - • UeW8J!flbeJ L4IJM 9DUepJODDe U! 00q pöuoe eq Ui (9 SMeJOS) 9 6u!JdS dwep u! eq u!ujni Aq esJaeJ o uiod iUoJ o JDD peeiq • eq öuuq pu Jetej ui5eue aqi
  • Pfaff 1246 | Owner's Manual - Page 74
    2 (screws 3) to the height stipulated in requirement 1. Omnusmt abcehiunnesscwreiwtheoduttoauotbotmaiantiaccpcreessssetor-fsocoretwlifste3r. (subclass -910/..), bracket 4 • By turning the handwheel, bring the machine to needle rise position and manually activate the engaging lever. PFAF
  • Pfaff 1246 | Owner's Manual - Page 75
    Allow the presser foot to rest on the needle plate. • By continuing to turn the handwheel, position the point of thread catcher 5 at the same height as the edge of rear stop trip 6 of the needle plate and press release bar 8 to the left in accordance with requirement 2 using retaining collar 7. • In
  • Pfaff 1246 | Owner's Manual - Page 76
    Positioner W R4AefmhtqeemrunitrriaeinmfmtteemrerrniuntthpgteitnhBgeDttChheroesfaedtwh, eitnhgneepmerdaolcceheisbnsae,r.tmheusmt apcohsiintieonmiutssetlfpaotsitthioenTiDtsCelfofatthaepprox. take-up lever. • Carry out the adjustment as stipulated in the instruction manual of the motor. PFP 11 - 38
  • Pfaff 1246 | Owner's Manual - Page 77
    SOlON
  • Pfaff 1246 | Owner's Manual - Page 78
    31
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
1245
1246
Instruction
manual
2962-17
841
Betriebsanleitung
engi.
10.97