Philips 15E4220T User manual
Philips 15E4220T Manual
 |
View all Philips 15E4220T manuals
Add to My Manuals
Save this manual to your list of manuals |
Philips 15E4220T manual content summary:
- Philips 15E4220T | User manual - Page 1
with precise parameters you desire. The wide range of scanning frequency supports variety of operating platforms, such as IBM PC and compatibles, any bad effects caused by the screen surface such as reflection of the room lights. • 85Hz refresh rate: The maximum display resolution is 1024 x 768 @60 - Philips 15E4220T | User manual - Page 2
E N Note: If you experienced your monitor display is changing from color to mono, it's possible that you are using a non-VESA-DDC-standard video card. Please consult with your local PCEC dealer for more information. ENERGY STAR is a U.S. registered mark. As an ENERGY STAR® Partner, PCEC has - Philips 15E4220T | User manual - Page 3
vents or which could cover them and prevent proper cooling of the monitor's electronic devices. x Do not expose the monitor to rain or excessive moisture to . x Consult a service technician if the monitor does not operate normally when operating instructions of this manual are followed. Package - Philips 15E4220T | User manual - Page 4
E N Installation Important: Please refer to the user's manuals of your computer and video adapter to make sure these equipments are properly installed and configured before angle. To fit the pedestal, refer to the illustration on the inside front-cover of this manual. 105 E 4 FUNC. RECALL - Philips 15E4220T | User manual - Page 5
Connection E N Important: Please make sure the AC power to your computer is "OFF" before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipments. Intel Based platform: 386, 486, Pentium, or - Philips 15E4220T | User manual - Page 6
monitor will be operating in power saving mode if you switch on your monitor without signal input from PC. (Please refer to Power Management Signalling instruction.) 6 - Philips 15E4220T | User manual - Page 7
E FUNC. RECALL FUNC. RECALL For an optimized adjustment of the picture following controls are available at the front. POWER. Press this knob, the green LED lights and the power is ON. Press this knob again, the green LED disappears and the power is OFF. How to use Digital control: 1. When - Philips 15E4220T | User manual - Page 8
E N H-Size : to adjust the horizontal amplitude of the image. H-Center : to adjust the horizontal position of the image. V-Size : to adjust the vertical amplitude of the image. V-Center : to adjust the vertical position of the image. Pincushion: to correct the barrel distortion of the image. - Philips 15E4220T | User manual - Page 9
E Adjustment N The monitor is pre-set with 7 modes for optimal display size and centering as indicated in the following table: Mode VGA VGA VESA/75 VESA /85 VESA/75 VESA/85 VESA/60 Resolution Horizontal Vertical (dots x lines) Freq.(KHz) Freq.(Hz) Remark 720 x 400 31.5 70 Non-interlaced - Philips 15E4220T | User manual - Page 10
LED color will change into following colors whenever the monitor goes into power management status. Green LED light - "Normal" operation Amber LED light - "Stand by" or "Suspend" mode Amber LED light - "OFF" mode This monitor is ENERGY STAR® compliant when used with a computer equipped with DPMS. As - Philips 15E4220T | User manual - Page 11
Picture tube : 15 inch (38.1 cm), 90° deflection, non- glare, black matrix,light transmission 57%, phosphor P22 medium short, dotted pitch 0.28 mm. Screen area Recommended Display Area: : . Intel based platform (386, 486, Pentium) and other compatibles. . VESA Guide lines and Standards. 11 - Philips 15E4220T | User manual - Page 12
E N (III) Pin assignment: 1 6 5 10 1 9 11 15 8 15 (1) (2) (1) The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. 1 2 3 4 5 6 7 8 Assignment Red video input Green video input Blue video input Identification output - Connected to pin 10 Ground Red video ground - Philips 15E4220T | User manual - Page 13
E 15E4220T N Digital Auto Scan Colour Monitor English Contents Introduction .... 1 Feature Highlights .... 1 Safety precautions and maintenance .... 3 Package .... 3 End of life disposal .... 3 Installation .... 4 Connection .... 5 Connection to the mains .... 6 Front Control - Philips 15E4220T | User manual - Page 14
E N OTHER LANGUAGE VERSIONS FRENCH(FRANCAIS) .... 13 Appendix English Information for Users in the U.S. FCC Declaration WARRANTY Deutsch Hinweis / GS / ACHTUNG Français FCC Declaration ........ A1 ........ A2 ........ A5 ........ A3 ........ A4
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
E
N
Introduction
The 105E colour monitor displays sharp and brilliant images of text and
graphics with a maximum resolution up to 1024x768 pixels. It is optimal
for Windows, spread sheets, and any other application.
This monitor automatically scans horizontal frequencies from 30KHz to
54KHz,and vertical frequencies from 50Hz to 120Hz.With microprocessor
based digital controlled circuit, the monitor can automatically adjust
itself to the video card’s scanning frequency and displays an image
with precise parameters you desire. The wide range of scanning
frequency supports variety of operating platforms, such as IBM PC and
compatibles, including Intel based platforms such as 386, 486, Pentium
and Pentium II .
Feature Highlights
•
Digital Control
feature provides user-friendliness and ease-of-use
when operating the monitor.
•
Anti-Glare
screen coating eliminate any bad effects caused by the
screen surface such as reflection of the room lights.
•
85Hz refresh rate:
The maximum display resolution is 1024 x 768 @60 hz non-interlaced
mode. The recommanded optimum resolution up to 800 x 600 pixels
non-interlaced by maximum 85Hz refresh rate.
•
DDC1/DDC2B
allows communication between the monitor and PC
system for optimal video configuration.
1