Pioneer DEH-P80MP Operation Manual - Page 51

Using subwoofer output, Using nonfading output, Audio Adjustments - rca

Get Pioneer DEH-P80MP PDF manuals and user guides View all Pioneer DEH-P80MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Audio Adjustments Section 11 English 3 Push Multi-Control left or right to select a desired level. Each pushing Multi-Control left or right selects level in the following order: LOW (low)MID (mid)HIGH (high) 4 To turn loudness off, press Multi-Control again. Loud OFF appears in the display. Using subwoofer output This unit is equipped with a subwoofer output which can be turned on or off. 1 Use Multi-Control to select Sub-W1. Sub-W1 appears in the display. # When the subwoofer controller setting is PREOUT:FULL, you cannot select Sub-W1. 2 Press Multi-Control to turn subwoofer output on. Sub-W1 Normal appears in the display. Subwoofer output is now on. # To turn subwoofer output off, press Multi-Control again. 3 Push Multi-Control left or right to select the phase of subwoofer output. Push Multi-Control left to select reverse phase and Rev. appears in the display. Push Multi-Control right to select normal phase and Normal appears in the display. Adjusting subwoofer settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Use Multi-Control to select Sub-W2. Sub-W2 appears in the display. # When the subwoofer output is on, you can select Sub-W2. 2 Push Multi-Control left or right to select cut-off frequency. Each pushing Multi-Control left or right selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push Multi-Control up or down to adjust the output level of the subwoofer. Each pushing Multi-Control up or down increases or decreases the level of the subwoofer. +6  6 is displayed as the level is increased or decreased. Using nonfading output When the nonfading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is outputted through the RCA output. 1 Use Multi-Control to select nonfading output on/off setting. NonFad ON appears in the display. # When the subwoofer controller setting is only PREOUT:FULL, you can switch to the nonfading output on/off setting. (Refer to page 55.) 2 Press Multi-Control to turn nonfading output on. NonFad ON appears in the display. Nonfading output is now on. # To turn nonfading output off, press Multi-Control again. En 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
3
Push Multi-Control left or right to select
a desired level.
Each pushing
Multi-Control
left or right se-
lects level in the following order:
LOW
(low)
³
MID
(mid)
³
HIGH
(high)
4
To turn loudness off, press
Multi-Control again.
Loud OFF
appears in the display.
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Use Multi-Control to select Sub-W1.
Sub-W1
appears in the display.
#
When the subwoofer controller setting is
PREOUT:FULL
, you cannot select
Sub-W1
.
2
Press Multi-Control to turn subwoofer
output on.
Sub-W1 Normal
appears in the display. Sub-
woofer output is now on.
#
To turn subwoofer output off, press
Multi-Control
again.
3
Push Multi-Control left or right to select
the phase of subwoofer output.
Push
Multi-Control
left to select reverse
phase and
Rev.
appears in the display. Push
Multi-Control
right to select normal phase
and
Normal
appears in the display.
Adjusting subwoofer settings
When the subwoofer output is on, you can ad-
just the cut-off frequency and the output level
of the subwoofer.
1
Use Multi-Control to select Sub-W2.
Sub-W2
appears in the display.
#
When the subwoofer output is on, you can se-
lect
Sub-W2
.
2
Push Multi-Control left or right to select
cut-off frequency.
Each pushing
Multi-Control
left or right se-
lects cut-off frequencies in the following order:
50
³
80
³
125
(Hz)
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
Push Multi-Control up or down to ad-
just the output level of the subwoofer.
Each pushing
Multi-Control
up or down in-
creases or decreases the level of the subwoo-
fer.
+6
±
±
6
is displayed as the level is
increased or decreased.
Using nonfading output
When the nonfading output setting is on, the
audio signal does not pass through this unit
²
s
low pass filter (for the subwoofer), but is out-
putted through the RCA output.
1
Use Multi-Control to select nonfading
output on/off setting.
NonFad ON
appears in the display.
#
When the subwoofer controller setting is only
PREOUT:FULL
, you can switch to the nonfading
output on/off setting. (Refer to page 55.)
2
Press Multi-Control to turn nonfading
output on.
NonFad ON
appears in the display. Nonfading
output is now on.
#
To turn nonfading output off, press
Multi-Control
again.
Audio Adjustments
En
51
English
Section
11