Pioneer DEH-P80MP Operation Manual - Page 55

Switching the auxiliary setting, Switching the dimmer setting, Adjusting the brightness, Setting

Get Pioneer DEH-P80MP PDF manuals and user guides View all Pioneer DEH-P80MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Initial Settings Section 12 English 2 Press Multi-Control to turn warning tone on. Warning :ON appears in the display. # To turn warning tone off, press Multi-Control again. Switching the auxiliary setting It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. 1 Use Multi-Control to select AUX. AUX appears in the display. 2 Press Multi-Control to turn AUX on. AUX :ON appears in the display. # To turn AUX off, press Multi-Control again. Switching the dimmer setting To prevent the display from being too bright at night, the display is automatically dimmed when the cars headlights are turned on. You can turn the dimmer on or off. 1 Use Multi-Control to select Dimmer. Dimmer appears in the display. 2 Press Multi-Control to turn dimmer on. Dimmer :ON appears in the display. # To turn dimmer off, press Multi-Control again. Adjusting the brightness You can adjust the display brightness. Initially this mode is set to 12. 1 Use Multi-Control to select Brightness. Brightness appears in the display. 2 Push Multi-Control left or right to adjust the brightness level. Each pushing Multi-Control left or right increases or decreases the brightness level. 0  15 is displayed as the level is increased or decreased. Setting the rear output and subwoofer controller This units rear output (rear speaker leads output and RCA rear output) can be used for fullrange speaker (REAR SP :FULL) or subwoofer (REAR SP :S/W) connection. If you switch the rear output setting to the REAR SP :S/W, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, the unit is set for rear full-range speaker connection (REAR SP :FULL). When rear output is connected to full range speakers (when REAR SP :FULL is selected), you can connect the RCA subwoofer output to a subwoofer. In this case, you can select whether to use the subwoofer controllers (low pass filter, phase) built-in PREOUT :S/W or the auxiliary PREOUT :FULL. 1 Use Multi-Control to select REAR SP. REAR SP appears in the display. 2 Press Multi-Control to switch the rear output setting. Pressing Multi-Control will switch between REAR SP :FULL (full-range speaker) and REAR SP :S/W (subwoofer) and that status will be displayed. # When no subwoofer is connected to the rear output, select REAR SP :FULL. # When a subwoofer is connected to the rear output, set for subwoofer REAR SP :S/W. En 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
2
Press Multi-Control to turn warning
tone on.
Warning :ON
appears in the display.
#
To turn warning tone off, press
Multi-Control
again.
Switching the auxiliary setting
It is possible to use auxiliary equipment with
this unit. Activate the auxiliary setting when
using auxiliary equipment connected to this
unit.
1
Use Multi-Control to select AUX.
AUX
appears in the display.
2
Press Multi-Control to turn AUX on.
AUX :ON
appears in the display.
#
To turn AUX off, press
Multi-Control
again.
Switching the dimmer setting
To prevent the display from being too bright at
night, the display is automatically dimmed
when the car
²
s headlights are turned on. You
can turn the dimmer on or off.
1
Use Multi-Control to select Dimmer.
Dimmer
appears in the display.
2
Press Multi-Control to turn dimmer on.
Dimmer :ON
appears in the display.
#
To turn dimmer off, press
Multi-Control
again.
Adjusting the brightness
You can adjust the display brightness. Initially
this mode is set to 12.
1
Use Multi-Control to select Brightness.
Brightness
appears in the display.
2
Push Multi-Control left or right to ad-
just the brightness level.
Each pushing
Multi-Control
left or right in-
creases or decreases the brightness level.
0
±
15
is displayed as the level is increased or
decreased.
Setting the rear output and
subwoofer controller
This unit
²
s rear output (rear speaker leads out-
put and RCA rear output) can be used for full-
range speaker (
REAR SP :FULL
) or subwoofer
(
REAR SP :S/W
) connection. If you switch the
rear output setting to the
REAR SP :S/W
, you
can connect a rear speaker lead directly to a
subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speak-
er connection (
REAR SP :FULL
). When rear
output is connected to full range speakers
(when
REAR SP :FULL
is selected), you can
connect the RCA subwoofer output to a sub-
woofer. In this case, you can select whether to
use the subwoofer controller
²
s (low pass filter,
phase) built-in
PREOUT:S/W
or the auxiliary
PREOUT:FULL
.
1
Use Multi-Control to select REAR SP.
REAR SP
appears in the display.
2
Press Multi-Control to switch the rear
output setting.
Pressing
Multi-Control
will switch between
REAR SP :FULL
(full-range speaker) and
REAR SP :S/W
(subwoofer) and that status will
be displayed.
#
When no subwoofer is connected to the rear
output, select
REAR SP :FULL
.
#
When a subwoofer is connected to the rear
output, set for subwoofer
REAR SP :S/W
.
Initial Settings
En
55
English
Section
12