Pioneer DR-U16S SCSI-2 Command Set Reference Manual

Pioneer DR-U16S Manual

Get Pioneer DR-U16S PDF manuals and user guides View all Pioneer DR-U16S manuals
Add to My Manuals
Save this manual to your list of manuals

Pioneer DR-U16S manual content summary:

  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 1
    CD-ROM SCSI-2 Command Set Reference Manual Version 3.1 (OB-U0077C) June 26, 1997 Pioneer Electronic Corporation Pioneer New Media Technologies, Inc.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 2
    CD-ROM SCSI-2 Command Set Reference Manual Version 3.1 (OB-U0077C)
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 3
    the product's fitness for any particular purpose. Every precaution has been taken in the preparation of this manual. Although we tried to thoroughly check that all instructions in this manual are accurate and correct, Pioneer can not be and is not responsible, in whole or in part, for any damage or
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 4
    described in this manual has been tested and not occur in a particular installation. To determine if your CD-ROM drive is causing interference, turn the drive off. If or modifications to this product that are not authorized by Pioneer could void the FCC Certification and negate the user's authority
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 5
    iv REVISION HISTORY...viii 1. PREFACE...1 1.1 DRM/DR-U Series...1 1.2 Drives Supported by this Manual 3 1.3 SCSI Protocol ...4 1.3.1 Command Link/Control Medium Types Supported Page 49 2.9.5 CD-ROM Parameters Page 51 2.9.6 CD-ROM Audio Control Parameters 53 2.9.7 CD-ROM Capabilities and
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 6
    (12) (AFh) ...151 2.44 Write Buffer (3Bh) ...153 2.45 Write CDP (E3h) ...155 2.46 Read CD-DA (D8h)...157 2.47 Read CD-DA MSF (D9h) ...161 2.48 READ CD-XA (DBh)...163 2.49 Read All SubCode (DFh)...165 APPENDIX A PIONEER CD-ROM DRIVES - AUDIO FUNCTIONS I APPENDIX B AUDIO PLAYER COMMANDS I - ii -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 7
    APPENDIX C DRIVE VERSION DIFFERENCES I APPENDIX D PRODUCTS DEFAULT DATA I D.1 Product data of Applied Model Number 3 (Inquiry Data I D.2 CD-ROM ABILITY MECHANICAL STATUS PAGE DEFAULT DATA III APPENDIX E CD-ROM COMMAND LIST (BY CODE I -iii-
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 8
    LIST OF TABLES TABLE 1-0 MODELS OF DRM/DR-U SERIES SUPPORTING SCS-2 COMMAND SET 2 TABLE 1-2 DRIVE VERSIONS SUPPORTED BY THIS MANUAL 2 TABLE 1-5 SAMPLE COMMAND...6 TABLE 2-0 SCSI-2 COMMAND LIST (BY NAME) ...8 TABLE 2-0A CD-ROM MODE PAGE CODE LIST...10 TABLE 2-1 AUDIO SCAN (1) ...12 TABLE 2-1A
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 9
    AUDIO CONTROL PARAMETERS STATUS FORMAT 52 TABLE 2-9-6A OUT PORT CHANNEL SELECT PARAMETERS 52 TABLE 2-9-7 PAGE CODE 2AH - CD-ROM CAPABILITIES AND MECHANICAL STATUS PAGE FORMAT 54 TABLE 2-9-7A PARAMETER DESCRIPTION ...56 TABLE 2-9-7B EXAMPLE DATA RATES ...57 TABLE 2-9-8 PAGE CODE 31H - DRIVE SPEED
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 10
    2-31C SUPPORTED ADDITIONAL SENSE CODES AND ADDITIONAL SENSE CODE QUALIFIERS 125 RESERVE (16H) ...128 REZERO UNIT (01H) ...130 SEEK(6) (0BH)...132 SEEK(10) (2BH)...134 SEND DIAGNOSTIC (1DH) ...136 TABLE 2-36A SEND DIAGNOSTIC DATA FORMAT...136 SET CD-ROM SPEED(1) (DAH)...138 SET CD-ROM SPEED(2) (BBH
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 11
    (DFH)...164 TABLE D-1A DR-U124X INQUIRY DATA FORMAT...I TABLE D-1B DR-UA124X INQUIRY DATA FORMAT...I TABLE D-1C DRM-624X INQUIRY DATA FORMAT ...II TABLE D-2A PAGE CODE 2AH : CD-ROM CAPABILITIES AND MECHANICAL STATUS PAGE DEFAULT DATA......... III TABLE E-1 CD-ROM COMMAND LIST BY CODE...I -vii
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 12
    1.2 Section 1.4 Sections 2.46 - 2.49 Description Initial release Addition of DRM-602X Vendor Unique Commands Addition of models DR-124X and DRM-624X Addition of Appendix D Addition of models DR-A10X, DR-411, DRU10X, DR-433, DR-A12X, DR-444, DRU12X, DR-466, DR-A24X, DR-511, DRU24X, DR-533 - viii -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 13
    LaserDisc Player (any model) User's Manuals. THESE SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 1.1 DRM/DR-U Series The six-disc DRM series drives are SCSI-21 CD-ROM minichangers using a single movable optical assembly and a removable Pioneer-developed 6-disc CD magazine. Six discs may be
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 14
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 1-0 MODELS OF DRM/DR-U SERIES SUPPORTING SCS-2 COMMAND SET Model Number DRM-602X DRM-604X DRM-624X DRM-1804X DR-D504X DR-U124X DR-UA124X DR-A10X DR-U10X DR-411 DR-433 DR-A12X DR-U12X DR-444 DR-466 DR-A24X DR-U24X DR-511 DR-533
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 15
    's DRM-5004X Series 500-Disc CD-ROM Changer Mechanism Controller SCSI Specifications, document number OB-U0091-B, for further details. Implementing Pioneer's LaserDisc player technology, vendor unique SCSI commands support the alphanumeric player command set allowing CD audio control through use of
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 16
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) 1.3 SCSI Protocol The SCSI Protocol outlined in this section applies only to SCSI bus models. It does not support 2 1 0 Flag Link The Command Link function is not supported by the DRM/DR-U Series. Set Flag and Link bits to "0" (FALSE
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 17
    to receive a new command. Refer to Section 2.31 REQUEST SENSE for details on deferred error reporting. 1.3.4 In-Phase/Out-Phase Messages The DRM/DR-U Series supports only those In-Phase and Out-Phase Messages that are listed below and on the following page. The drive will return a MESSAGE REJECT
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 18
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 1-5 SAMPLE COMMAND Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (XXh) 1 Logical Number Reserved 2 Logical Block Address (MSB) 3 Logical Block Address 4 Logical Block Address 5 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 19
    answering data. MSF bit if "0" (FALSE), use Logical Block Address as CD-ROM Absolute Address or Track Relative Address. If Track Relative Address, the MSF bit will transfer to the drive. 3 For equipment supporting Change Definition Command, the DRM/DR-U Series drives have a Hardware Reset Option.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 20
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) The drive terminates the DATA IN phase when the specified number of bytes have been transferred or, in the case when the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 21
    Unit 01h yes yes yes Seek (6) 0Bh yes yes yes Seek (10) 2Bh yes yes yes Send Diagnostic 1Dh yes yes yes Set CD-ROM Speed (1) BBh --- --- yes Set CD-ROM Speed (2) DAh yes yes yes Start/Stop Unit 1Bh yes yes yes Stop Play/Scan 4Eh --- --- yes Test Unit Ready 00h yes yes
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 22
    of single type drive. 7 : is not supported by DR-A10X, DR-U10X, DR-411, DR-433, DR-A12X, DRU12X, DR-444, DR-466, DR-A24X, DR-U24X, DR-511 and DR-533. Upon execution of some commands, a Page Code is returned. The table on the next page lists the various CD-ROM Mode Page Codes. NOTE: The Applied Model
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 23
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-0A CD-ROM MODE PAGE CODE LIST Page Code 00h 01h 07h 0Bh 0Dh 0Eh 2Ah 31h 3Eh 3Fh Description Only Block Descriptor Read Error Recovery Page Verify Error Recover page Peripheral Device page CD-ROM Parameters page CD-ROM Audio
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 24
    code 4h, 8h, 70h, 71h and 72h. There is limited action in the CD-ROM Audio Controller Parameter Page (0Eh). 3 : random access is possible with CD-DA data. Buffer Over Flow Error would not occur. For SUB-CHANNEL READ OUT, support is only when the Beginning Logical Block Address is FFFFFFFFh and Sub
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 25
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-1 AUDIO SCAN (1) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (CDh) 1 Logical Unit Number Direct Reserved 2 Scan Start Address (MSB) 3 Scan Start Address 4 Scan Start
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 26
    commands without scan termination: AUDIO PLAY (StpAdr=1), AUDIO STATUS, AUDIO STOP INQUIRY MODE SELECT, MODE SENSE READ BUFFER, WRITE BUFFER READ CD-ROM CAPACITY, READ SUB CHANNEL, READ TOC RECEIVE DIAGNOSTIC RESULTS, REQUEST SENSE, TEST UNIT READY RELEASE, RESERVE There are several commands that
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 27
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-1B AMIN, ASEC AND AFRAME ADDRESS FORMAT (TYPE = 01B) Bit Byte 7 6 5 4 3 2 1 0 2 Reserved 3 CD absolute time (AMIN) 4 CD absolute time (ASEC) 5 CD absolute time (AFRAME) AMIN, ASEC and AFRAME show the absolute
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 28
    Audio Scan (1) Type defines the format of the Scan Start address field. Type has four parameters. The four (4) parameters are 00b : Logical Block Address format 01b : AMIN, ASEC and AFRAME format 10b : Track Number Address format 11b : Reserved (reference Table 2-1A) (reference Table 2-1B) (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 29
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-2 AUDIO SCAN (2) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (BAh) 1 Reserved Direct Reserved 2 Scan Starting Address (MSB) 3 Scan Starting Address 4 Scan Starting Address 5 Scan
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 30
    Audio Scan (2) 2.2 Audio Scan (2) (BAh) Operation Code is (BAh). Direct If "0" (FALSE), the drive scans forward. If "1" (TRUE), the drive scans backwards. Scan Start Address is the address at which the audio scan begins operation. Type defines the format of the Scan Start address field. Type
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 31
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-3 CHANGE DEFINITION Bit Byte 7 6 5 4 3 2 1 0 Operation Code (40h) 1 Logical Unit Number Reserved 2 Reserved 3 Reserved Definition Parameter 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Parameter
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 32
    initial operating definition. Definition Parameter specifies the operating definition. The Definition Parameter field supports the following field values: 00h : Use current operating definition 01h : SCSI DEFINITION command are: DRM-602X, DRM-624X, DRM-1804X and the DR-U Series drives - 19 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 33
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-4 INQUIRY Bit Byte 7 6 5 4 3 2 0 Operation Code (12h) 1 Logical 0 0 0 SYNC 0 Reserve 0 0 Vendor Name (8-byte ASCII code) (PIONEER) Product Inquiry Data (16-byte ASCII code) Revision Number (ASCII code) ("XXXX
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 34
    the standard Inquiry data format. RMB If "1" (TRUE), the media is removable. TIOP If "1" (TRUE), the drive will support the Terminate I/O Process message. SYNC If "1" (TRUE), the drive supports synchronous data transfers. Table 2-4B on the next page outlines the drive specific values for bytes 16~31
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 35
    MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-4B DRIVE SPECIFIC STRINGS Drives DRM-602X DRM-604X DRM-624X DRM-1804X DR-D504X DR-A10X DR-U10X DR-411 DR-433 DR-A12X DR-U12X DR-444 DR-466 DR-A24X DR-U24X DR-511 DR-533 Bytes 16 ~ 31 (Product Data) CD-ROM DRM-602X CD-ROM DRM-604X CD-ROM DRM-624X CD-ROM
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 36
    Inquiry (this page has been left intentionally blank) - 23 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 37
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-5 MODE SELECT(6) (15H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (15h) 1 Logical Unit Number PF Reserved SP 2 Reserved 3 Reserved 4 Parameter List Length 5 Reserved TABLE 2-
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 38
    (TRUE). The drive does not check the value of the Page Format bit. SP (Save Parameters) Must be set to "0" (FALSE). Parameter saving is not supported. Parameter List Length If "0" (ZERO), no data will be transferred. The Parameter List Length is the number of bytes of the Mode Select Parameter List
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 39
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-5B BLOCK DESCRIPTOR Bit Byte 7 6 5 4 3 2 1 0 0 Density Code 1 Number of Blocks (MSB) 2 Number of Blocks 3 Number of Blocks (LSB) 4 Reserved 5 Block Length (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 40
    256, 512, 1024, 2048(default), 2052, 2056, 2336, 2340 and 2352 byte are supported. An external switch on the back of the DRM-602X, DRM-604X and DRM-1804X of the data contained in the page. Page Length is the number of bytes supported for each page. It does not include the page length byte. The drive
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 41
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-6 MODE SELECT(10) (55H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (55h) 1 Logical Unit Number PF Reserved SP 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7 Parameter
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 42
    the command fields. IMPORTANT: Initiators should issue the MODE SENSE command (reference Sections 2.7 and 2.8) prior to each execution of the MODE SELECT command to determine supported pages, page lengths and other parameters. - 29 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 43
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-7 MODE SENSE(6) (1AH) Bit Byte 7 6 5 4 3 2 1 0 Operation Code (1Ah) 1 Logical Unit Number Reserved DVD Reserved 2 PCF Page Code 3 Reserved 4 Allocation Length 5 Reserved
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 44
    "0", the drive terminates the DATA IN phase when Allocation Length bytes or all the Sense data have been transferred. The following PCF codes are supported: 00b : Current value: The drive returns the values specified by the latest MODE SELECT command. If no MODE SELECT command has been issued, the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 45
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-7C MEDIA TYPE CODE Media Type Code 00h 01h 02h 03h 04h 05h 06h 07h 08h ~ FFh Type of Media Default 120mm CD-ROM Data 120mm CD-DA Audio 120mm CD-ROM Data/Audio Reserved 80mm CD-ROM Data 80mm CD-ROM Audio 80mm CD-ROM Data/Audio
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 46
    logical block size in bytes. In the current version, 256, 512, 1024, 2048(default), 2052, 2336, 2340 and 2352 byte are supported. The default values for the CD-ROM drives (512 or 2048) are selectable with an external switch. Density Code 01h : User data only (2048 bytes/physical sector)(default
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 47
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-8 MODE SENSE(10) (5AH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (5Ah) 1 Logical Unit Number Reserved DVD Reserved 2 PCF Page Code 3 Reserved 4 Reserved 5 Reserved 6
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 48
    Mode Sense(10) 2.8 Mode Sense(10) (5Ah) Operation Code is (5Ah) The MODE SENSE(10) command provides a means for a target to report parameters to the initiator. It is the complementary command to the MODE SELECT(10) command. See MODE SENSE(6) command (reference Section 2.7) for a complete description
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 49
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9 MODE SELECT/SENSE PARAMETERS Bit Byte 7 6 5 4 3 2 1 0 0 ~ N Mode Parameter Header 0 ~ N Page(s) TABLE 2-9A MODE PAGE CODES FOR CD-ROM Page Code 00h 01h 07h 0Bh 0Dh 0Eh 2Ah 31h 3Eh 3Fh Description Only Block
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 50
    Mode Select/Sense Parameters 2.9 Mode Select/Sense Parameters This section describes the pages used with MODE SELECT and MODE SENSE commands. The Mode Parameter List contains a header, followed by zero or more variable -length pages. Each mode page contains a page code, a page length , and a set of
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 51
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-1 PAGE CODE 01H - ERROR RECOVERY PARAMETERS Bit Byte 7 6 5 4 3 2 1 0 0 Reserve Reserve Page Code (01h) 1 Page Length (06h) 2 Reserve Reserve TB RC EEC
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 52
    Error Recovery Parameters 2.9.1 Error Recovery Parameters NOTE: When the bit definition of this error recovery parameter and the error recovery procedure (described later) are not in agreement, the error recovery procedure takes priority. DCR (Disable Correction) If "1", data is transferred without
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 53
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-1B ERROR RECOVERY DESCRIPTIONS Value 00h 01h 04h 05h 06h 07h Description The maximum error recovery procedures available are used. If
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 54
    Error Recovery Parameters TABLE 2-9-1B ERROR RECOVERY DESCRIPTIONS (CONTINUED) Value 10h 11h 14h 15h 20h Description If data transfer can be maintained, the maximum error recovery procedures available are used. (RC=1) If an error occurs which is uncorrectable with the error correction codes (ECC)
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 55
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-1B ERROR RECOVERY DESCRIPTIONS (CONTINUED) Value 21h 24h 25h 26h 27h Description Only retries of the read operation and CIRC are
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 56
    The CD-ROM errors are: Error Recovery Parameters 1) Recovered CIRC (Cross Interleaved Reed-Solomon Code) Error: An error in a block had been detected by the EDC (Error Detection
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 57
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-2 PAGE CODE 07H - VERIFY ERROR RECOVERY PAGE FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 PS Reserve Page Code (07h) 1 Page Length (06h) 2 Error Recovery Parameter 3
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 58
    Verify Error Recovery Page 2.9.2 Verify Error Recovery Page PS (Parameters Savable) The Parameters Savable bit is only used with the MODE SENSE command. This bit is reserved with the MODE SELECT command. A PS bit of one indicates that the target is capable of saving the page in a non-volatile vendor
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 59
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-3 PAGE CODE 09H - PERIPHERAL DEVICE PAGE FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 Reserved Page Code (09h) 1 Page Length (06h) 2 Interface Identifier (MSB) 3 Interface Identifier (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 60
    Peripheral Device Page 2.9.3 Peripheral Device Page Interface Identifier Codes are in Table 2-9-3A on the opposite page. The peripheral device page is used to pass vendor-specific information between an initiator and a peripheral interface below the target. - 47 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 61
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2.9.4 PAGE CODE 0BH - MEDIUM TYPES SUPPORTED PAGE FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 PS Reserve Page Code (0Bh) 1 Page Length (06h) 2 Reserved 3 Reserved 4 Medium Type One Supported 5 Medium Type Two
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 62
    of one indicates that the target is capable of saving the page in a non-volatile vendor specific location. The code values for each medium type supported by the target (up to four maximum), as defined in the MODE SELECT command are reported in ascending order. If only the default medium type
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 63
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-5 PAGE CODE 0DH - CD-ROM PARAMETERS PAGE FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 Reserve Reserve Page Code (0Dh) 1 Parameter Length (06h) 2 Reserved 3 Reserved Inactivity Timer Multiplier 4 5 Number of MSF-S
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 64
    Multiplier. Number of S per M units The number of S units per M unit field gives the ratio of these MSF address values. For media conforming to the CD-ROM and CD-DA standard, this value is 60 (3Ch). Number of F per S units The number of F units per S unit field gives the ratio of these MSF
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 65
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-6 PAGE CODE 0EH - CD-ROM AUDIO CONTROL PARAMETERS STATUS FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 Reserved Page Code (0Eh) 1 Page Length (0Eh) 2 Reserved Immed SOTC Reserve 3 Reserved 4 Reserved 5 Reserved 6
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 66
    indicates the output is muted, a value of FFh indicates the maximum level. The output volume is defined by averaging port 0 and port 1. The CD-ROM audio control parameter page sets the playback modes and output controls of subsequent Play Audio commands and any current audio playback operation. - 53
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 67
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-7 PAGE CODE 2AH - CD-ROM CAPABILITIES AND MECHANICAL STATUS PAGE FORMAT Byte 0 1 2 3 Reserve Reserve Form1 C2 Pointer are supported R-W Deinterleave d & corrected R-W supported 1 0 CD-DA Stream is Accurate Loading
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 68
    Page 2.9.7 CD-ROM Capabilities and Mechanical Status Page IMPORTANT: This command applies only to models DRM-602X, DRM-624X, DRU124X, DR-UA124X The individual capabilities of the drive are specified by bytes 4 through 7. Each of the bits indicate if that specific capability is supported. A value
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 69
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-7A PARAMETER DESCRIPTION Bit Sub-channel information. 1 XA Commands Supported This bit has been reserved for future support of CD-ROM XA commands. Drives which set this bit shall support all CD-ROM XA commands. 4 Mode 2
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 70
    CD-ROM Capabilities and Mechanical Status Page TABLE 2-9-7A PARAMETER DESCRIPTION ( / second 387 Kbytes / second 528 Kbytes / second 706 Kbytes/second The Maximum Speed Supported field indicates the actual maximum data rate that the drive supports. This value is returned as the number of kilobytes
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 71
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) (this page has been left intentionally blank) - 58 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 72
    CD-ROM Capabilities and Mechanical Status Page The Buffer Size Supported field returns the number of bytes of buffer dedicated to the data stream returned to the Host Computer. This value is returned in Kbytes (Size/
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 73
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-8 PAGE CODE 31H - DRIVE SPEED PAGE Bit Byte 7 6 5 4 3 2 1 0 0 Reserved Page code (31h) 1 Parameter Length (02h) 2 Speed 3 Reserved TABLE 2-9-8A SPEED FIELD
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 74
    . A speed setting value of 03h will not cause an error, but set the drive to 2x speed. DRM-624x, DRM-604X, DR-U124X, DR-UA124X, DR-D504X These drives do not support 2x Speed. A speed setting value of 01h will not cause an error. However, the drive will automatically be set to 4x speed
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 75
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-9-9 PAGE CODE 3EH - LOGICAL UNIT ASSIGNMENT LIST Bit Byte 7 6 5 4 3 2 1 0 0 Reserve Reserve Page Code (3Eh) 1 Page Length : (06h) 2 0 Number of supported discs (MSB) : (00h) 3 Number of supported discs (LSB) :
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 76
    Logical Unit Assignment Page 2.9.9 Logical Unit Assignment Page Number of supported discs The drive supports 6 discs. 0006h is always returned, and 124x will return 1 . Disc numbers Shows the disk number assigned to each logical unit. Disc number 0 means that the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 77
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-10 PAUSE/RESUME (4BH) Byte 7 0 1 2 3 4 5 6 7 8 9 6 5 Logical Unit No. Bit 4 3 Operation Code (4Bh) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 2 1 Reserved 0 Resume - 64 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 78
    Pause/Resume 2.10 Pause/Resume (4Bh) Operation Code is (4Bh) Resume A Resume of zero indicates that the drive enter the hold track state with the audio output muted. A Resume bit of one indicates that the drive release the pause and begin play at the block following the last block played. The PAUSE/
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 79
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-11 PLAY AUDIO(10) (45H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (45h) 1 Logical Unit No. Reserved 2 Starting Logical Block Address (MSB) 3 Starting Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 80
    audio operations are implemented then the PLAY AUDIO command will be implemented to allow a method for the initiator to determine if audio operations are supported. A target responding to a PLAY AUDIO command which has transfer length of zero with Check Condition status and setting the sense key to
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 81
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-12 PLAY AUDIO(12) (A5H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (A5h) 1 Logical Unit No. Reserved 2 Logical Block Address (MSB) 3 Logical Block Address 4
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 82
    Play Audio(12) 2.12 Play Audio(12) (A5h) Operation Code is (A5h). The PLAY AUDIO(12) command requests that the drive begin an audio playback operation. The command function (Immed and SOTC bits) and the output of audio signals shall be specified by the settings of the mode parameters. See the PLAY
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 83
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-13 PLAY AUDIO MSF (47H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (47h) 1 Logical Unit No. Reserved 2 Reserved 3 Starting M Field 4 Starting S Field 5 Starting F Field 6
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 84
    Play Audio MSF 2.13 Play Audio MSF (47h) Operation Code is (47h) Starting M/S/F Field Specifies absolute starting address in minutes, seconds, frame number. Ending M/S/F Field Specifies absolute ending address in minutes, seconds, frame number. The PLAY AUDIO MSF command requests the target to begin
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 85
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-14 PLAY AUDIO TRACK INDEX (48H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code(48h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Starting Track 5 Starting Index 6
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 86
    Play Audio Track Index 2.14 Play Audio Track Index (48h) Operation Code is (48h). Starting Track/Index The starting track field specifies the track number of the starting audio track. The starting index field specifies the index number within the track at which the audio play operation shall begin.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 87
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-15 PLAY AUDIO TRACK RELATIVE(10) (49H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (49h) 1 Logical Unit No. Reserved 2 Track Relative Logical Block Address (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 88
    Play Audio Track Relative(10) 2.15 Play Audio Track Relative(10) (49h) Operation Code is (49h). TRLBA The Track Relative Logical Block Address field specifies the two's complement starting logical block address relative to the beginning of the first sector on the track with an index value of one.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 89
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-16 PLAY AUDIO TRACK RELATIVE(12) (A9H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code(A9h) 1 Logical Unit No. Reserved 2 Track Relative Logical Block Address (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 90
    Play Audio Track Relative(12) 2.16 Play Audio Track Relative(12) (A9h) Operation Code is (A9h). The PLAY AUDIO TRACK RELATIVE(12) command requests that the device begin an audio playback operation. The command function (Immed and SOTC bits) and the output of audio signals shall be as specified by
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 91
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-17 PREVENT/ALLOW MEDIA REMOVAL (1EH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (1Eh) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved Prev 5 Reserved - 78 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 92
    Prevent/Allow Media Removal 2.17 Prevent/Allow Media Removal (1Eh) Operation code is (1Eh). Prev (Prevent bit) When this bit is set to 1, EJECT DISK commands (C0h) and the Eject Button on the drive are ignored. When it is 0, media removal is allowed. This command is used to prevent or allow media
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 93
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-18 READ(6) (08H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (08h) 1 Logical Unit No. Logical block address (MSB) 2 Logical block address 3 Logical block address (LSB) 4 Transfer Length 5 Reserved - 80 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 94
    Read(6) 2.18 Read(6) (08h) Operation Code is (08h). This six-byte READ command only allows reads of up to 255 blocks. The logical blocks will have the length set by MODE SELECT or the power-on default. For longer reads, use the ten-byte READ(10) command. After a read operation, the drive holds the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 95
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-19 READ(10) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (28h) 1 Logical Unit No. Reserved 2 Logical block address (MSB) 3 Logical block address 4 Logical block
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 96
    head at the last read track until an inactivity time-out occurs. NOTE: The DPO, FUA and RelAdr bits (not shown) in byte 1 are not supported, and must be set to 0. - 83 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 97
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-20 READ BUFFER (3CH) Bit Byte 7 6 5 4 3 2 0 Operation Code (3Ch) 1 Logical Unit No. Reserved 2 Buffer ID : (00h) 3 Buffer offset (MSB) 4 Buffer offset 5
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 98
    Read Buffer 2.20 Read Buffer (3Ch) Operation Code is (3Ch). Mode specifies meaning of the Buffer Offset field. Buffer ID is not supported. This byte is always 00h. Buffer Offset The byte offset in the buffer at which the read shall begin. This must be between 0 and 15.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 99
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-21 READ CD-ROM CAPACITY (25H) Bit Byte 7 6 5 4 3 2 0 Operation Code (25h) 1 Logical Unit No. Reserved 2 Logical block address (MSB) (00h) 3 Logical block address (00h) 4 Logical block address (00h) 5 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 100
    ) Operation code is (25h). This command requests the drive to return physical parameters of the CD-ROM disc currently loaded. The Logical Block Address, RelAdr (Byte 1, bit 0), and PMI (Byte 8, bit 0) parameters are not supported and must be set to 0. The drive sends the initiator the 8-byte data as
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 101
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-22 READ CD (BEH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (BEh) 1 Reserved Expected Sector Type Reserved 2 (MSB) 3 Starting Logical Block Address 4 5 (LSB) 6 (MSB) 7 Transfer Length in Blocks 8 (LSB
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 102
    Read CD-ROM Capacity 2.22 Read CD (BEh) IMPORTANT: This command applies only to models DRM-602X, DRM-624X, DR-U124X, DR-UA124X Operation data stream. All the field types are mandatory. If the drive does not support the C2 pointers (as reported in the Mode sense Capabilities page) the data returned
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 103
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-22B READ CD, HEADER CODE FIELD DEFINITION Header(s) Header and Sub-header will be placed in the data stream. TABLE 2-22C READ CD, ERROR FLAG FIELD DEFINITION Error Flags Definition 00b None 01b C2 Error Flag data 10b
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 104
    padded with zeros depending on the R-W Supported and R-W de-interleaved and error-corrected bits in the CD-ROM capabilities and mechanical status page. If bytes returned based on which Data Selection field bits are set. The CD-DA audio data includes 16bits of information for each channel, and will
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 105
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-22D READ CD, SUB CHANNEL DATA SELECTION FIELD transferred Q Not Supported Reserved R - W R-W data will be transferred Reserved TABLE 2-22E NUMBER OF BYTES RETURNED BASED ON DATA SELECTION FIELD Flag Bits CD-DA Sync 80h
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 106
    Read CD-ROM Capacity (this page has been left intentionally blank) - 93 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 107
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-23 READ CD MSF (B9H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (B9h) 1 Reserved Expected User data type Reserved 2 Reserved 3 Starting M Field 4 Starting S Field 5 Starting F Field 6 Ending M Field 7
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 108
    MSF 2.23 Read CD MSF (B9h) IMPORTANT: This command applies only to models DRM-602X, DRM-624X, DR-U124X, DR-UA124X The Starting M field, the Starting S field, and the Starting F field specify the absolute MSF address at which the Read operation shall begin. The Ending M
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 109
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-24 READ CDP (E4H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (E4h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Allocation length (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 110
    Read CDP 2.24 Read CDP (E4h) Operation Code is (E4h) This command requests the drive to return the status data resulting from the previous WRITE CDP command. The drive terminates the data phase when Allocation Length bytes or all the relevant data have been transferred. The last status data returned
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 111
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-25 READ DRIVE STATUS (E0H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (E0h) 1 Logical Unit No. Reserved 2 PCF Page Code 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 112
    Read CDP 2.25 Read Drive Status (E0h) Operation Code is (E0h) PCF (Page Control Field) indicates the type of Page Parameter to be returned. 00b : Current Value 01b : Reserved 10b : Reserved 11b : Reserved Page Code indicates contents of the Page Parameters. 01h : Drive Status 02h : Audio Play Status
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 113
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-25B DRIVE STATUS DATA FORMAT Bit Byte 7 6 5 4 3 2 1 0 0 Reserved Page Code : (01h) 1 Page Length (MSB) (00h) 2 Page Length (LSB) (02h) 3 Drive Status (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 114
    read 0: Data track reads only 1: Data track reads and play audio/video tracks 0: Read only 1: Supports Read and Write commands 0: Supports only 2048-byte block size 1: Supports 2048 and 2353-bytes block size 0: Magazine locked 1: Magazine unlocked 0: Magazine inserted 1: No magazine inserted
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 115
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-26 READ HEADER (44H) Bit Byte 7 6 5 4 3 2 0 Operation Code (44h) 1 Logical Unit No. Reserved 2 Logical block address (MSB) 3 Logical block address 4 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 116
    of the returned header data will indicate the MSF address where the specified logical block is found. If MSF bit is equal to 0, the absolute CD-ROM Address field of the returned header data gives the logical block address of the first logical block in the physical sector where the specified logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 117
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-27 READ SUB-CHANNEL (42H) Bit Byte 7 6 5 4 3 2 0 Operation Code (42h) 1 Logical Unit No. Reserved 2 Reserved SubQ Reserved 3 Sub Channel Data Format 4
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 118
    the current block plus the status of an audio play operation. Format Code Sub-Channel Data Block 00h : Q Sub-code Data 01h : CD-ROM Current Position 02h : Media Catalog Number (UPC/Bar Code) 03h : Track International Standard Recording Code (ISRC) 04h-FFh : Reserved The returned sub
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 119
    REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-27B SUB-CHANNEL Q MODE INFORMATION Bit Byte 7 6 5 4 3 2 1 0 4 Sub Channel Data Format code (00h) 5 ADR Control 6 Track Number 7 Index Number 8 Absolute CD-ROM Address (MSB) 9 Absolute CD-ROM Address 10 Absolute CD-ROM Address
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 120
    bits are defined in Table 2-23E Track Number specifies the current Track Number Index Number specifies the current index number in the current track. Absolute CD-ROM Address returns the current location relative to the logical beginning of the media. If the MSF bit in the CDB is zero, this field is
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 121
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-27D ADR SUB-CHANNEL Q FIELD ADR Code 0h 1h 2h 3h 4h ~ Fh Description sub-channel Q mode information not supplied sub-
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 122
    Read Sub-Channel The ADR field shows the type of information encoded in the Q sub-Channel of this block as defined in the CD standard. MCV If the MCV bit is one, the media catalog number field is valid. There are identify numbers according to the UPC/EAN cording
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 123
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-27G MEDIA CATALOG NUMBER DATA BLOCK Bit Byte 7 6 5 4 3 2 1 0 4 Sub Channel Data Format code (02h) 5 Reserved 6 Reserved 7 Reserved 8 MCV Reserved 9 (MSB) 23
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 124
    Read Sub-Channel (this page has been left intentionally blank) - 111 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 125
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-28 READ TOC (43H) Bit Byte 7 6 5 4 3 2 0 Operation Code (43h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 Start Track 7 Allocation Length (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 126
    table of contents to the initiator. This command has been modified from the SCSI-2 READ TOC command with the addition of the Format field to support multi-session discs. Format field 00b 01b 10b 11b Definition Same as SCSI-2. The Start Track Field specifies the starting track number for which the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 127
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-28C TOC DATA WITH FORMAT=01B Bit Byte 7 4 3 2 1 0 Reserved ADR Control First Track Number in Last Session Reserved Absolute CD-ROM Address of the First Track in the Last Session TABLE 2-28E TOC DATA WITH FORMAT=
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 128
    the TOC track descriptor is valid. A track number of 0AAh indicates the track descriptor is for the start of the lead-out area. The absolute CD-ROM address contains the address of the first block with user information for that track number as read from the table of contents. An MSF bit
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 129
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-28F TRACK DESCRIPTORS Bit Byte 7 6 5 4 3 2 1 0 0 Reserved 1 ADR Control 2 Byte1 or TNO 3 Byte2 or Point 4 Byte3 or Min 5 Byte4 or Sec 6 Byte5
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 130
    Read TOC (this page has been left intentionally blank) - 117 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 131
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-29 RECEIVE DIAGNOSTIC RESULTS (1CH) Bit Byte 7 6 5 4 3 2 1 0 6 5 4 3 2 1 0 0 Reserved 1 Parameter Length (06h) 2 ROM Diagnostic 3 RAM Diagnostic 4 Data Buffer Diagnostic 5 Reserved 6 Reserved - 118
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 132
    The number of bytes of the RECEIVE DIAGNOSTIC parameter excluding itself. This is fixed to 06h. ROM Diagnostic Bit 0 = 1, failure of the SCSI controller ROM. Bit 1 = 1, failure of the drive controller ROM. RAM Diagnostic Bit 0 = 1, failure of the SCSI controller RAM. Bit 1 = 1, failure of the drive
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 133
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-30 RELEASE (17H) Byte 7 6 5 0 1 Logical Unit Number 2 3 4 5 Bit 4 3 2 1 Operation Code (17h) 3rdPty 3rd Party device ID Reservation ID : 00h Reserved Reserved Reserved 0 Ext (0) - 120 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 134
    3rd Party device ID The SCSI ID of another initiator for which the logical unit shall be reserved. Ext. (Extent) Not supported. This bit must be 0. Reservation ID Not supported. This byte must be 00h. This command is used by the reserving initiator to release the previous reservation of the logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 135
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-31 REQUEST SENSE (03H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (03h) 1 Logical Unit Number Reserved 2 Reserved 3 Reserved 4 Allocation Length (12h) 5 Reserved TABLE 2-31A
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 136
    Sense (03h) Operation Code is (03h). The REQUEST SENSE command requests the drive to transfer extended sense data to the initiator. The drive supports the first 18 bytes of the extended sense data format. The drive will transfer Allocation Length bytes or 18 bytes, whichever is smaller. Valid
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 137
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-31B SUPPORTED SENSE KEYS Sense Key 0h 1h 2h 3h 4h 5h 6h 7h 8h Bh Others Name no Write-once device encountered blank medium or format defined end of data indication while reading. Target aborted command. not supported - 124 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 138
    Request Sense TABLE 2-31C SUPPORTED ADDITIONAL SENSE CODES AND ADDITIONAL SENSE CODE QUALIFIERS ASC 00 00 becoming ready logical unit not ready, initializing command required logical unit not ready, manual intervention required logical unit does not respond to selection no reference position found
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 139
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) Table 2-31C Supported additional sense codes and additional sense code qualifiers (continued) ASC ASCQ DESCRIPTION 21 00 logical block address out of range 24 00 invalid field in CDB 25 00 logical unit not supported 26 00
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 140
    Request Sense (this page has been left intentionally blank) - 127 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 141
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-32 RESERVE (16H) Bit Byte 7 6 5 4 3 2 1 0 Operation Code (16h) 1 Logical Unit No. 3rdPty 3rd Party Device ID 2 Reservation ID (00h) 3 Extent List
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 142
    . These bytes must be 00h. The initiator uses this command to exclusively reserve the specified logical unit. Area reservations using the Extent bit are not supported. If the 3rd Party bit is 1, the logical unit is reserved for another SCSI device specified by the 3rd Party Device ID. The initiator
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 143
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-33 REZERO UNIT (01H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (01h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved - 130 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 144
    Rezero Unit 2.33 Rezero Unit (01h) Operation Code is (01h). The drive loads the specified logical unit (if necessary), spins up the disc (if stopped), moves the head to the start track of the disc, and holds it there until an inactivity time-out occurs. If the initiator requests a disconnect, the
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 145
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-34 SEEK(6) (0BH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (0Bh) 1 Logical Unit No. Logical Block Address (MSB) 2 Logical Block Address 3 Logical Block Address (LSB) 4 Reserved 5 Reserved - 132 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 146
    Seek(6) 2.34 Seek(6) Operation Code is (0Bh). The drive seeks to the specified logical block address and then holds at that track until an inactivity time-out occurs. - 133 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 147
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-35 SEEK(10) (2BH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (2Bh) 1 Logical Unit No. Reserved 0 2 Logical Block Address (MSB) 3 Logical Block Address 4 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 148
    Seek(10) 2.35 Seek(10) (2Bh) Operation code is (2Bh). The drive seeks to the specified logical block address and then holds at that track until an inactivity time-out occurs. - 135 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 149
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-36 SEND DIAGNOSTIC (1DH) Bit Byte 7 6 5 4 3 2 6 5 4 3 2 1 0 0 Reserved 1 Parameter Length (06h) 2 ROM Diagnostic 3 RAM Diagnostic 4 Data Buffer Diagnostic 5 Interface Diagnostic 6 Reserved 7 Reserved
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 150
    HARDWARE ERROR is returned. Use RECEIVE DIAGNOSTIC RESULTS to determine the problem area. If self bit is zero, target returns GOOD status itself. This is fixed to 06h. ROM Diagnostic Bit 0 = 1, test the SCSI controller ROM. Bit 1 = 1, test the drive controller ROM. RAM Diagnostic Bit 0 = 1, test
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 151
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-37 SET CD-ROM SPEED(1) (DAH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (DAh) 1 Reserved 2 Speed 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Reserved 9 Reserved 10 Reserved 11
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 152
    Set CD-ROM Speed(1) 2.37 Set CD-ROM Speed(1) (DAh) Operation code is (DAh). The Set CD-ROM Speed command provides a means for set the drive to 2x speed. DRM-624x, DRM-604x, DR-U124x, DR-UA124X, and DR-D504X These drives do not support 2x Speed. A speed setting value of 01h will not cause
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 153
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-38 SET CD-ROM SPEED(2) (BBH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation code (BBh) 1 Reserved 2 (MSB) Drive Speed in Kbytes/Second 3 (LSB) 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Reserved 9
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 154
    Set CD-ROM Speed(2) 2.38 Set CD-ROM Speed(2) (BBh) The Drive Speed parameter contains the requested Data Rate the drive should use. The drive may choose to select the speed specified or any slower rate. A value of FFFFh will set the Drive Speed to the Maximum supported. Requesting a speed faster
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 155
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-39 START/STOP UNIT (1BH) Bit Byte 7 6 5 4 3 2 0 Operation Code (1Bh) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 1 0 Immed LoEj Start - 142 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 156
    Start/Stop Unit 2.39 Start/Stop Unit (1Bh) Operation code is (1Bh). Immed (Immediate) When the immediate bit is 1, status is returned before executing the command . When it is 0, status is returned after the operation is completed. LoEj (Load Eject) When LoEj is 1 and Start is 0, the drive ejects
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 157
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-40 STOP PLAY/SCAN (4EH) Bit Byte/Bit 7 6 5 4 3 2 1 0 0 Operation code (4Eh) 1 Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Reserved 9 Reserved 10
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 158
    Stop Play/Scan 2.40 Stop Play/Scan (4Eh) The STOP PLAY/SCAN CD-ROM Command stops playback of CD-ROM audio commands. - 145 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 159
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-41 TEST UNIT READY (00H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (00h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved - 146 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 160
    Test Unit Ready 2.41 Test Unit Ready (00h) Operation Code is (00h). The TEST UNIT READY command checks that a cartridge is loaded and that the drive is ready to operate. "Ready" has different meanings depending on whether the drive has accessed a logical unit by loading the disc tray: Before access
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 161
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-42 VERIFY(10) (2FH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (2Fh) 1 Logical Unit No. Reserved Blkvry Bytchk RelAdr 2 Logical block address (MSB) 3 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 162
    SELECT command). No data transfer on the SCSI bus occurs. NOTE: The BlkVry (Blank verify), BytChk (Byte Check) and RelAdr bits in byte 1 are not supported, and should be set to 0. - 149 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 163
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-43 VERIFY(12) (AFH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (AFh) 1 Logical Unit No. Reserved 0 0 0 2 Logical block address (MSB) 3 Logical block address 4 Logical
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 164
    2.43 Verify(12) (AFh) Operation code is (AFh). See VERIFY(10) for complete description of this command. Verify(12) - 151 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 165
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-44 WRITE BUFFER (3BH) Bit Byte 7 6 5 4 3 2 0 Operation Code (3Bh) 1 Logical Unit No. Reserved 2 Buffer ID (00h) 3 Buffer offset (MSB) 4 Buffer offset 5
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 166
    Write Buffer 2.44 Write Buffer (3Bh) Operation Code is (3Bh). Mode specifies meaning of the Buffer Offset field. Buffer ID is not supported. This byte must be 00h. Buffer Offset is the byte offset in the buffer where the data shall be stored. This must be 0 through 15.
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 167
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-45 WRITE CDP (E3H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (E3h) 1 Logical Unit No. Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 Reserved 7 Reserved 8 Transfer length (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 168
    Write CDP 2.45 Write CDP (E3h) Operation Code is (E3h). Transfer Length is the number of bytes of CDP command data to be sent. This command sends alphanumeric Player Control commands to the drive. The drive returns the command status after the player control command is transferred to the drive
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 169
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-46 READ CD-DA (D8H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (D8h) 1 Logical Unit Number Reserved 2 (MSB) 3 4 Starting Logical Block Address 5 (LSB) 6 Reserved 7 (MSB) 8 Transfer length 9 (LSB) 10
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 170
    (D8h) IMPORTANT: This command applies only to models DRM-602X, DRM-624X, and the DR-U Series drives. Operation Code is (D8h). The READ CD-DA command requests that the drive transfer CD-DA data and/or Sub Code data. The Starting Logical Block Address specifies the block where the READ operation
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 171
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) NOTES: 1) The CD-DA block lengths are totally irrelevant to the logical block length set by the Mode Select(6) command. This command would not change the block length
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 172
    Read CD-DA (this page has been left intentionally blank) - 159 -
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 173
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-47 READ CD-DA MSF (D9H) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (D9h) 1 Logical Unit No. Reserved 2 Reserved 3 Starting M Field 4 Starting S Field 5 Starting F Field 6 Reserved 7 Ending M Field 8
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 174
    MSF 2.47 Read CD-DA MSF (D9h) IMPORTANT: This command applies only to models DRM-602X, DRM-624X, and the DR-U Series drives. Operation Code is (D9h). Starting M, S, F Fields indicates the absolute MSF address where the operation begins. Ending M, S, F Fields indicates the absolute MSF address where
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 175
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-48 READ CD-XA (DBH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (DBh) 1 Logical Unit No. Reserved 2 (MSB) 3 Starting Address 4 5 (LSB) 6 CD-XA Format 7 (MSB) 8 9 Transfer Length 10 (LSB) 11
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 176
    -602X, DRM-624X, and the DR-U Series drives. Operation Code is (DBh). Starting Address specifies the block where the operation begins. Transfer Length specifies the number of contiguous CD-XA blocks to be transferred. The READ CD-XA command requests that the drive transfer CD-XA data to the host
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 177
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE 2-49 READ ALL SUBCODE (DFH) Bit Byte 7 6 5 4 3 2 1 0 0 Operation Code (DFh) 1 Logical Unit Number Reserved 2 Reserved 3 Reserved 4 Reserved 5 Reserved 6 (MSB) 7 8 Transfer Length 9 (
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 178
    Read All SubCode 2.49 Read All SubCode (DFh) IMPORTANT: This command applies only to models DRM-602X, DRM-624X, and the DR-U Series drives. Operation Code is (DFh) Transfer Length indicates the number of contiguous sub-code frames to be transferred. Each sub-code frame consists of
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 179
    executed in the background. At times, the two subsystems may be operating independently. In addition to the normal audio commands, the CD-ROM drives support the Pioneer Laser Disc Player control commands. These alphanumeric mnemonics may be sent to the drive using the vendor-unique command WRITE CDP
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 180
    APPENDIX B AUDIO PLAYER COMMANDS Addressing Modes Block Index Time Track MMSSFF I I MMSS TT Specifies Minutes, Seconds, and Frames. Specifies pre-mastered indices Specifies Minutes and Seconds (Frame 0) Specifies the beginning of track TT Player Modes P00 Home P00 Home P01 Park P03 Stop P04
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 181
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) CM IX ?K n KL LO NF NR ?O ?P PA PL ?Q N3: Data Track 0: Not Present 1: Present X: Unknown N4: CDV 0: No 1: Yes X: Unknown N5: CD-I 0: No 1: Yes X: Unknown N6-8: Reserved (All X) Key Lock Enables or disables the front panel
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 182
    audio playback level, from 0 to 255. Returns the revision of the CDP ROM Example: "P150801" Returns a three digit number representing the currently loaded disc. magazine not inserted Search address not found Focus lost (Hardware problem) The spindle is not locking Front panel Eject button pressed
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 183
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) Example To load Disc 3 and start playing from 21m 34s 16bl, use the command 3ZSSABK213416SEPL. 3ZS: Load Disc 3 SA: Start rotation BK: Block Addressing 213416SE: Search to 21 Minutes, 34 Seconds, 16 Blocks PL: Begin Play. B-IV
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 184
    APPENDIX C DRIVE VERSION DIFFERENCES DRM-602X 2900 Current Version DRM-604X 2401 Current Version Does Not Support SCSI-2 2403 Supports SCSI-2 Supports Multi-session Photo CD. DRM-1804X 0100 Current Version Appendix C C-I
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 185
    2 Additional length : 42 (2Ah) Reserved Reserved 0 0 0 Sync=1 0 Reserve 0 0 Vendor name (8-byte ASCII code) Continue "PIONEER" Product inquiry data (16-byte ASCII code) Continue "CD-ROM DR-124X" Revision number (ASCII code) Ex."0100" Release Version : 20h Revision Date(10-byte ASCII
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 186
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) TABLE D-1C DRM-624X INQUIRY DATA FORMAT Byte 0 1 2 3 4 5 6 7 8 ~ 15 0 0 Vendor name (8-byte ASCII code) Continue "PIONEER" Product inquiry data (16-byte ASCII code) Continue "CD-ROM DRM-624X" Revision number (ASCII code) Ex."0100"
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 187
    2AH : CD-ROM CAPABILITIES AND CD-DA CD-DA supported =1 Supported String Commands =0 =1 =1 =1 Loading Mechanism Type Reserved Eject Prevent Lock Lock 124X=001b,624X=000b =1 JP =1 State =1 Reserved Sp.Mute Sp.volume =1 =1 (MSB) Maximum Speed Supported (in KBps) DR-UA124X=706,DR
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 188
    CD-ROM SCSI-2 COMMAND REFERENCE MANUAL VERSION 3.1 (OB-U0077C) APPENDIX E CD-ROM COMMAND LIST (BY CODE) TABLE E-1 CD-ROM COMMAND LIST BY CODE Code 00h 01h 03h 08h 0Bh 12h 15h 16h 17h 1Ah 1Bh 1Ch 1Dh 1Eh 25h 28h 2Bh 2Fh 3Bh 3Ch
  • Pioneer DR-U16S | SCSI-2 Command Set Reference Manual - Page 189
    CD-ROM SCSI-2 Command Set Reference Manual Version 3.1 Pioneer Electronic Corporation 4-1, Meguro 1-chome Meguro-Ku, Tokyo 153 JAPAN www.pioneer.co.jp Pioneer New Media Technologies, Inc. 2265 East 220th Street Long Beach, California 90810 UNITED STATES OF AMERICA (310) 952-2111 www.pioneerusa.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
CD-ROM
SCSI-2 Command Set
Reference Manual
Version 3.1
(OB-U0077C)
June 26, 1997
Pioneer Electronic Corporation
Pioneer New Media Technologies, Inc.