Pioneer PD-F27 Operating Instructions - Page 24

Troubleshooting

Page 24 highlights

TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work. Symptom No sound Cause • Output cables are connected incorrectly or loosely. • Incorrect operation of stereo amplifier. • Pin plugs and/or amplifier terminals are dirty. • Player is in pause mode. • The disc is loaded with the label side leftward. Remedy • Connect properly. • Check the settings of amplifier switches and sound volume controls. • Clean away dirt. • Press 3 or 8. • Reload the disc with the label side rightward. When playback is started, it stops immediately. Pauses or stops during playback. • Disc is inserted in the wrong way. • Smudges, etc., on the disc. • Insert the disc correctly with the label side leftward. • Clean the smudges from the disc and then play it again. Remote control will not function. • Dead batteries. • Obstruction between player and remote control unit. • Replace batteries. • Relocate remote control unit or remove obstruction. SLAVE unit does not operate when 2 units are connected. • Incorrect connection. • Refer to "Connecting another PD-F27" on page 6, 7 and reconnect the 2 units. Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation unplug the AC power cord and then plug it in again. SELF-DIAGNOSTICS FUNCTION The unit incorporates the self-diagnostic function. When an abnormality is detected during operation of the unit, an error message (service No.) appears on the unit's display automatically. Treat the error by following the instructions in "Countermeasures". Display on the unit Service No. RENTAL DISC TRACK REMAIN MIN SEC ALL RANDOM REPEAT - 1 BEST ADLC CUSTOM SINGLE CD TEXT PREVIOUS SCAN PROGRAM Service No. U1 Unit Status The disc may not be loaded properly in the rack. Countermeasures • Reload the discs properly. (Insert only one disc in a slot.) • Check if there is a foreign object attached onto the disc. • Check if there is a foreign object in the rack. U2 There is an operation error in the mechanical section. • Check if there is a foreign object in the rack. • Unplug the power cord then plug it in again. U3 There is an error related to the hood. • Check if the hood is caught by anything. • Unplug the power cord then plug it in again. If the same display appears again, there may be an error in the mechanical section. When requesting servicing, please also let us know the service number displayed on the unit. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

24
RENTAL
DISC
TRACK
REMAIN
MIN
SEC
ALL
RANDOM
REPEAT - 1
BEST
ADLC
CUSTOM
SINGLE
CD TEXT
PREVIOUS
SCAN
PROGRAM
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the
points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your
dealer to carry out repair work.
Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation unplug the AC
power cord and then plug it in again.
Symptom
No sound
When playback is started, it
stops immediately.
Pauses or stops during
playback.
Remote control will not
function.
SLAVE unit does not operate
when 2 units are connected.
Cause
Output cables are connected incorrectly or
loosely.
Incorrect operation of stereo amplifier.
Pin plugs and/or amplifier terminals are dirty.
Player is in pause mode.
The disc is loaded with the label side leftward.
Disc is inserted in the wrong way.
Smudges, etc., on the disc.
Dead batteries.
Obstruction between player and remote control
unit.
Incorrect connection.
Remedy
Connect properly.
Check the settings of amplifier switches and
sound volume controls.
Clean away dirt.
Press
3
or
8
.
Reload the disc with the label side rightward.
Insert the disc correctly with the label side
leftward.
Clean the smudges from the disc and then
play it again.
Replace batteries.
Relocate remote control unit or remove
obstruction.
Refer to “Connecting another PD-F27” on
page 6, 7 and reconnect the 2 units.
SELF-DIAGNOSTICS FUNCTION
The unit incorporates the self-diagnostic function.
When an abnormality is detected during operation of the unit, an error message (service No.) appears on the unit‘s display automatically. Treat
the error by following the instructions in
”Countermeasures”.
Display on the unit
Service No.
U1
U2
U3
Unit Status
The disc may not be loaded properly in the rack.
There is an operation error in the mechanical
section.
There is an error related to the hood.
Countermeasures
Reload the discs properly.
(Insert only one disc in a slot.)
Check if there is a foreign object attached onto
the disc.
Check if there is a foreign object in the rack.
Check if there is a foreign object in the rack.
Unplug the power cord then plug it in again.
Check if the hood is caught by anything.
Unplug the power cord then plug it in again.
If the same display appears again, there may be an error in the mechanical section. When requesting servicing, please also let us know the
service number displayed on the unit.
Service No.