Pioneer VSX-D509S Owner's Manual - Page 18

SUB WOOFER ON/PLUS/OFF setting mode

Get Pioneer VSX-D509S PDF manuals and user guides View all Pioneer VSX-D509S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Preparations SUB WOOFER ON/PLUS/OFF setting mode Sets whether the SUB WOOFER is used or not. Also, when used you have the option to use the "PLUS" setting. memo • Initial setting is "ON". • Setting the front speaker size to "Small" in the SPEAKERS setting mode automatically locks the sub woofer in the "ON" position. • Use the PLUS for extra bass. When you use PLUS you will get the bass sounds from the sub woofer even if the front speakers are set to "Large". Press % or fi to select sub woofer ON, PLUS or dB OFF. Crossover frequency setting mode Crossover frequency is the point where the receiver divides the high and low sounds (the frequencies) between the speakers. Since most smaller speakers can't handle deep bass tones, this setting allows you to send those sounds to the sub woofer (or speakers set to "Large" if you don't have a sub woofer) instead of the speakers set to "Small" in your system. Choose the point at which you want the frequency routed to the sub woofer (or "Large" speakers). We recommend setting this to 200 Hz if smaller bookshelf-type speakers are used for your "Small" speakers. memo • Initial setting is "100 Hz". • If all speakers (front, center, and surround) are set to "Large" in SPEAKERS setting mode, crossover frequency cannot be set because there are no "Small" speakers (*** appears in the display). Press % or fi to specify the crossover frequency dB for your small speakers (100 Hz, 150 Hz or 200 Hz). 100Hz 150Hz 200Hz 100 Hz Sends bass frequencies below 100 Hz to the sub woofer (or "Large" speakers). 150 Hz Sends bass frequencies below 150 Hz to the sub woofer (or "Large" speakers). 200 Hz Sends bass frequencies below 200 Hz to the sub woofer (or "Large" speakers). LFE attenuator setting mode Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as needed to prevent the ultra-low bass tones from distorting the sound from the speakers. • Initial setting is "0 dB". ∗∗ memo • When ∞ is selected ( appears in the display), LFE is not available. dB 0 dB 10 dB 18 ∞ (display "**") Press % or fi to set the attenuation level (0 dB, 10 dB or ∗∗ dB(∞)).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
18
Preparations
dB
dB
memo
memo
memo
SUB WOOFER ON/PLUS/OFF setting mode
Sets whether the SUB WOOFER is used or not. Also, when used you have the option to use the “PLUS”
setting.
•
Initial setting is “ON”.
•
Setting the front speaker size to “Small” in the SPEAKERS setting mode automatically
locks the sub woofer in the “ON” position.
•
Use the PLUS for extra bass. When you use PLUS you will
get the bass sounds from the
sub woofer even if the front speakers are set to “Large”.
Press
%
or
fi
to select sub woofer ON, PLUS or
OFF.
Crossover frequency setting mode
Crossover frequency is the point where the receiver divides the high and low sounds (the frequencies) between
the speakers. Since most smaller speakers can’t handle deep bass tones, this setting allows you to send those
sounds to the sub woofer (or speakers set to “Large” if you don’t have a sub woofer) instead of the speakers
set to “Small” in your system. Choose the point at which you want the frequency routed to the sub woofer (or
“Large” speakers).
We recommend setting this to 200 Hz if smaller bookshelf-type speakers are used for your “Small” speakers.
•
Initial setting is “100 Hz”.
•
If all speakers (front, center, and surround) are set to “Large” in SPEAKERS setting mode,
crossover frequency cannot be set because there are no “Small” speakers (*** appears
in the display).
Press
%
or
fi
to specify the crossover frequency
for your small speakers (100 Hz, 150 Hz or 200
Hz).
100 Hz
Sends bass frequencies below 100 Hz to the sub woofer (or “Large”
speakers).
150 Hz
Sends bass frequencies below 150 Hz to the sub woofer (or “Large”
speakers).
200 Hz
Sends bass frequencies below 200 Hz to the sub woofer (or “Large”
speakers).
LFE attenuator setting mode
Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as needed to prevent
the ultra-low bass tones from distorting the sound from the speakers.
•
Initial setting is “0 dB”.
•
When
∞
is selected (
appears in the display), LFE is not available.
Press
%
or
fi
to set the attenuation level (0 dB,
10 dB or
dB(
∞
)).
10 dB
0 dB
∞
(display "
**
")
150Hz
100Hz
200Hz
dB