Pioneer VSX-D814-S Operating Instructions

Pioneer VSX-D814-S Manual

Get Pioneer VSX-D814-S PDF manuals and user guides View all Pioneer VSX-D814-S manuals
Add to My Manuals
Save this manual to your list of manuals

Pioneer VSX-D814-S manual content summary:

  • Pioneer VSX-D814-S | Operating Instructions - Page 1
    AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D514 VSX-D714 VSX-D814 Operating Instructions
  • Pioneer VSX-D814-S | Operating Instructions - Page 2
    important operating and maintenance (servicing) instructions in the literature accompanying or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the multi-voltage models. The factory setting for the voltage selector is 220 V. Please set it to
  • Pioneer VSX-D814-S | Operating Instructions - Page 3
    range of remote control unit . . . 6 04 Controls and displays Front panel (VSX-D514 27 Front panel (VSX-D714/D814 29 Display 31 Remote control 32 02 5 minute guide Introduction to home theater 7 Listening to Surround Sound 8 Using the Quick Setup 12 03 Connecting up Audio/Video cords 14
  • Pioneer VSX-D814-S | Operating Instructions - Page 4
    remote control settings . . 62 Direct function 62 Controls for TVs 63 Controls for other components 64 Preset Code List (VSX-D514/D714 66 Preset Code List (VSX-D814 68 10 Additional information Troubleshooting 70 Resetting the main unit 72 Switching the speaker impedance 72 Specifications
  • Pioneer VSX-D814-S | Operating Instructions - Page 5
    • Remote control • Power cords (make sure you use the correct cord for your country/region): VSX-D514/D714/D814-K (black models) Round 2-pin type and Australian type VSX-D514/D714-S (silver models) Round 2-pin type, flat blade 2-pin type and UK 3-pin type (Except Australian model) VSX-D814-S (silver
  • Pioneer VSX-D814-S | Operating Instructions - Page 6
    you start Operating range of remote control unit The remote control may not work properly if: • There are obstacles between the remote control and the receiver's remote sensor. • Direct sunlight or fluorescent light is shining onto the remote sensor. • The receiver is located near a device that
  • Pioneer VSX-D814-S | Operating Instructions - Page 7
    of the action or concert. The surround sound you get from a home theater system depends not only on the speakers you have set up in your room, but also on the source and the sound settings of the receiver. DVD-Video has become the basic source material for home theater due to its size, quality, and
  • Pioneer VSX-D814-S | Operating Instructions - Page 8
    Listening to Surround Sound This receiver was designed with the easiest possible setup in mind, so with the following quick setup guide, you should have your system hooked up for surround sound in no time at all. In most cases, you can simply leave the receiver in the default settings. Be sure
  • Pioneer VSX-D814-S | Operating Instructions - Page 9
    Español 5 minute guide 02 3 Connect your speakers. A complete setup of speakers is shown here (six speakers for the VSX-D514/D714, and eight for the VSX-D814), but different home setups may vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just
  • Pioneer VSX-D814-S | Operating Instructions - Page 10
    /LD IN S-VIDEO E A K A E R SINGLE SEE INSTRUCTION MANUAL B IN PLAY S R AUDIO L VSX-D814 Passive Powered subwoofer SW subwoofer or single surround TV back INPUT speaker AUDIO IN • If you're not using a subwoofer, change the front speaker setting (see Speaker setting on page 46
  • Pioneer VSX-D814-S | Operating Instructions - Page 11
    to the left channel (-) terminal. Surround back speaker (or subwoofer) VSX-D814 R SURROUND BACK L 4 Plug in the receiver and switch it on, followed by your DVD player, your subwoofer and the TV. Make sure you've set the video input on your TV to this receiver. Check the manual that came with the TV
  • Pioneer VSX-D814-S | Operating Instructions - Page 12
    panel controls for the steps below. ADVANCED STEREO/ SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP TENING MODE MMER DIGITAL IN VIDEO INPUT S-VIDEO VIDEO L AUDIO R ENTER MULTI JOG MASTER VOLUME DOWN UP * VSX-D814 only If a subwoofer
  • Pioneer VSX-D814-S | Operating Instructions - Page 13
    are nearer to the front speakers than the surround speakers MID - If you are equal distance from the front and surround speakers BACK - If you are nearer to the surround speakers than the front speakers 8 Press ENTER to confirm your setup. The display shows the speaker setup, room size and listening
  • Pioneer VSX-D814-S | Operating Instructions - Page 14
    between the signals is avoided. Connect from the component video jacks on the rear of the receiver to the component video jacks on the video component you are hooking up. Y Green Blue P B P R Red S-video cables Use S-video cables (not supplied) to get clearer picture reproduction than
  • Pioneer VSX-D814-S | Operating Instructions - Page 15
    MONITOR OUT OUT CONTROL R L SURROUND DVD 5.1CH INPUT CO MONITOR O IN OUT DVR/ VCR OUT IN MONITOR TV/ OUT SAT IN SUB WOOFER DVD PREOUT / LD IN S-VIDEO S P E A K A E R S Y PB R FRONT L DVD player DIGITAL OUT COAX * The illustration shows the VSX-D814, but connections
  • Pioneer VSX-D814-S | Operating Instructions - Page 16
    TV/ OUT SAT IN SUB WOOFER DVD PREOUT /LD IN S-VIDEO S P E A K A E R S Y PB R FRONT L PR CENTER Y PB PR (T V / SAT)IN ø R SURROUND BACK L SINGLE SEE INSTRUCTION MANUAL * The illustration shows the VSX-D814, but connections for the VSX-D514/D714 are the same. 16 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 17
    CENTER PREOUT R SURROUND BACK L OFURRTOPNSUURTRTOUND L SUORURTROPUFURONTNTD L L L SINGLE SEE INSTRUCTION MANUAL R R SUB WOOFER OUTPUT B CENTER OUTPUT VIDEO OUTPUT This receiver* DVD/multi-channel decoder with multi-channel analog output jacks * The illustration shows the VSX-D814, but
  • Pioneer VSX-D814-S | Operating Instructions - Page 18
    PB R FRONT L PR CENTER Y PB PR (T V / SAT)IN ø R R FRONT SURROUND CENTER PREOUT R SURROUND BACK L R SURROUND L INPUT SINGLE SEE INSTRUCTION MANUAL VIDEO TV (monitor) * The illustration shows the VSX-D814, but connections for the VSX-D514/D714 are the same. Connecting to the front
  • Pioneer VSX-D814-S | Operating Instructions - Page 19
    CD-R IN / TAPE / MD IN PLAY R AUDIO L VIDEO CENTER SUB WOOFER AM LOOP ANTENNA MONITOR OUT OUT CONTROL R L SURROUND DVD 5.1CH INPUT IN OUT DVR/ VCR OUT IN MONITOR TV AM loop antenna Assemble the antenna and connect to the receiver. Attach (if necessary) and face in the direction
  • Pioneer VSX-D814-S | Operating Instructions - Page 20
    up Connecting the speakers (VSX-D514/D714) A complete setup of six speakers (including the subwoofer) is shown below, but everyone's home setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the
  • Pioneer VSX-D814-S | Operating Instructions - Page 21
    (T V / SAT)IN ø FRONT SURROUND PREOUT S R FRONT L P E A K A E R CENTER R SURROUND BACK L R SURROUND L SINGLE SEE INSTRUCTION MANUAL R FRONT L B IN PLAY S R AUDIO L VSX-D814 Passive Powered subwoofer SW subwoofer or single surround TV back INPUT speaker AUDIO IN 21 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 22
    B speaker systems VSX-D714/D814 only The receiver has two speaker systems: A and B. A is the main system supporting the full speaker setup. If you switch on both A and B speaker systems, only the front speakers and the (active) subwoofer will be audible. No sound will come from the center, surround
  • Pioneer VSX-D814-S | Operating Instructions - Page 23
    the receiver to turn off automatically. Surround Back Left Surround Back Right Single Surround Back Speaker 3-D view of 6.1 channel speaker setup Speaker placement diagrams The following illustrations show 6.1 and 7.1 channel speaker setups. 3-D view of 7.1 channel speaker setup • VSX-D514
  • Pioneer VSX-D814-S | Operating Instructions - Page 24
    SUB WOOFER DVD PREOUT /LD SURROUND BACK S-VIDEO IN S P E A K A E R S Y PB R FRONT L PR CENTER Y PB PR (T V / SAT)IN ø R SURROUND L R FRONT L ANALOG IN Powered subwoofer B Surround back channel amplifier or powered speaker ANALOG IN VSX-D814 L R IN DIGITAL OUT OPT IN
  • Pioneer VSX-D814-S | Operating Instructions - Page 25
    Pioneer authorized service center or your dealer for a replacement. Operating other Pioneer components VSX-D714/D814 only By connecting a control cord (optional), you can point the remote controls of other Pioneer components at the receiver's remote sensor. The remote control signals are received
  • Pioneer VSX-D814-S | Operating Instructions - Page 26
    you need to make a few settings in the receiver. See Using the SR+ mode with a Pioneer plasma display on page 54 for detailed instructions. CONTROL Pioneer plasma display OUT Media receiver VIDEO INPUT 3 Pioneer plasma display VIDEO INPUT 1 DVD player Satellite receiver, etc IN DIGITAL OUT
  • Pioneer VSX-D814-S | Operating Instructions - Page 27
    /ON PHONES 3 45 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D514 ENTER MULTI JOG MASTER VOLUME DOWN UP 7 6 8 9 10 11 12 13 14 15 16 STATION TUNING ADVANCED STEREO/ STANDARD SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKER IMPEDANCE VSB MODE TONE QUICK SETUP TUNER EDIT CLASS
  • Pioneer VSX-D814-S | Operating Instructions - Page 28
    the bass and treble at low volume (page 41). 13 SPEAKER IMPEDANCE Use to change the impedance setting (page 72) 14 VSB MODE Selects the Virtual Surround Back (VSB) mode (page 40). 15 TONE Press this button to access the bass and treble controls, which you can then adjust with the MULTI JOG dial
  • Pioneer VSX-D814-S | Operating Instructions - Page 29
    PHONES 34 5 6 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D814 ENTER MULTI JOG MASTER VOLUME DOWN UP 8 7 9 10 11 12 13 14 15 16 17 STATION TUNING ADVANCED STEREO/ STANDARD SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP TUNER EDIT CLASS
  • Pioneer VSX-D814-S | Operating Instructions - Page 30
    button to access the bass and treble controls, which you can then adjust with the MULTI JOG dial (page 41). 17 QUICK SETUP See Using the Quick Setup on page 12. 18 VIDEO INPUT See Connecting to the front panel video terminal on page 18. 19 DIGITAL IN VSX-D814 only See Connecting to the front panel
  • Pioneer VSX-D814-S | Operating Instructions - Page 31
    signal. 4 2 PRO LOGIC II (x) When the (STANDARD) Pro Logic II mode of the receiver is on, this lights to indicate Pro Logic II decoding. VSX-D714/D814 only - The x lights to indicate Pro Logic IIx decoding (see Listening in surround sound on page 36 for more on this). 5 VIR.SB Lights during Virtual
  • Pioneer VSX-D814-S | Operating Instructions - Page 32
    between -10 dB and -0 dB. Remote control Illustration shows the VSX-D714/D814 remote control 1 2 3 4 5 6 RECEIVER INPUT SELECT SOURCE DVD/LD MULTI CONTROL TV / SAT DVR/VCR TV CONT CD CD-R/TAPE TUNER RECEIVER ADVANCED STEREO/ MIDNIGHT/ STANDARD SURROUND DIRECT LOUDNESS CH TEST SELECT
  • Pioneer VSX-D814-S | Operating Instructions - Page 33
    the remote to control the receiver (used to select the features such as SLEEP, MCACC SETUP, etc). Also use this button to set up surround sound (page 44, page 52). 3 RECEIVER CONTROL buttons STANDARD Press for Standard decoding and to switch between the various Pro Logic II and (VSX-D714/D814 only
  • Pioneer VSX-D814-S | Operating Instructions - Page 34
    included in multilingual DVD-Video discs. SLEEP Use to put the receiver in sleep mode and select the amount of time before the receiver turns off. 6 (TUNE +/-, ST +/-) /ENTER Use the arrow buttons when setting up your surround sound system (see page 44). Also used to control DVD menus/options
  • Pioneer VSX-D814-S | Operating Instructions - Page 35
    English Italiano Français Deutsch Nederlands Español Controls and displays 04 Use to turn on/off the power of the TV. (TV CONTROL) INPUT SELECT Use select the TV function. CHANNEL +/- Use to select channels. VOLUME +/- Use to adjust the volume on your TV. 35 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 36
    Using this receiver, you can listen to any source in surround sound. However, the options available will depend on your speaker setup and the type of source you're listening to. If you connected surround back speakers, see also Using the Surround Back Channel (SB CH) on page 39. VSX-D714/D814 only
  • Pioneer VSX-D814-S | Operating Instructions - Page 37
    sources. Try different settings with various soundtracks to see which you like. Pro Logic for a stereo surround effect. You can also VSX-D514) / 6-STEREO (VSXD714/D814) - This can be selected to give multichannel sound to a stereo source, using all of the speakers in your setup. • PHONES SURROUND
  • Pioneer VSX-D814-S | Operating Instructions - Page 38
    the receiver to select between input signals. ADVANCED STEREO/ STANDARD SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP LISTENING MODE INPUT ATT FL DIMMER DIGITAL IN VIDEO INPUT S-VIDEO VIDEO L AUDIO R * Illustration shows the VSX-D814 model
  • Pioneer VSX-D814-S | Operating Instructions - Page 39
    Using the Surround Back Channel (SB CH) (VSX-D714/D814 only) • Default setting: SB ON (VSX-D814), SB OFF (VSX-D714) You Surround back channel is switched off • You can't use the surround back channel with headphones, the STEREO / DIRECT mode, or if the Surround back speaker setting on page 46 is set
  • Pioneer VSX-D814-S | Operating Instructions - Page 40
    headphones, the STEREO / DIRECT mode, or if the Speaker setting on page 46 is set to S . VSX-D714/D814 only • You can only use the Virtual Surround Back mode if the surround speakers are on and the Surround back speaker setting on page 46 is set to SB or (VSX-D814 only) SB SW. • You can't adjust the
  • Pioneer VSX-D814-S | Operating Instructions - Page 41
    you to hear effective surround sound of movies at control. SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP DIGITAL IN VIDEO INPUT S-VIDEO VIDEO bit source and 96 kHz PCM. * Illustration shows the VSX-D814 model 1 Press TONE to select the frequency you want to
  • Pioneer VSX-D814-S | Operating Instructions - Page 42
    model: ADVANCED STEREO/ STANDARD SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP LISTENING MODE INPUT ATT FL DIMMER DIGITAL IN VIDEO INPUT S-VIDEO VIDEO L AUDIO R * Illustration shows the VSX-D814 model 1 Press DVD/LD on the remote control
  • Pioneer VSX-D814-S | Operating Instructions - Page 43
    standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer. 1 Press RECEIVER. 2 Press SLEEP repeatedly to set the sleep time. 90 min 60 min Off 30 min • You can check the remaining
  • Pioneer VSX-D814-S | Operating Instructions - Page 44
    (page 48) Specifies the distance from your listening position to your surround back speakers. Subwoofer distance setting (page 49) Specify the distance from your listening position to your subwoofer. Dynamic range control setting (page 50) Compress the dynamic range of the sound track. Dual mono
  • Pioneer VSX-D814-S | Operating Instructions - Page 45
    Coaxial digital input 2 setting • Optical digital input 1 setting VSX-D714/D814: Speaker setting (page 46) Specify the number and type of speakers you have connected. Surround back speaker setting (page 46) Specify your surround back speaker/ surround back subwoofer setup. Subwoofer setting (page 47
  • Pioneer VSX-D814-S | Operating Instructions - Page 46
    ) determines how much bass is sent from the receiver to the speakers. If you have connected a subwoofer to the surround back terminals (VSX-D814 only), you should select the surround back subwoofer setting (SB SW) from the options. Choose (asterisk) if no speaker is connected. • Use or to select SB
  • Pioneer VSX-D814-S | Operating Instructions - Page 47
    200 Hz to the subwoofer (or L speakers). • If all speakers (front, center, and surround) are set to L, the crossover frequency can't be set because there are no S speakers ( display). appears in the • If you chose the small front speaker setting, SW YES is automatically set and locked. Crossover
  • Pioneer VSX-D814-S | Operating Instructions - Page 48
    at the same time. Surround speaker distance setting VSX-D514 only • Default setting: 3 m You should set the distance of the surround speakers accurately to hear sounds coming from all speakers at the same time. • Use or to set the distance of the surround speaker from the main listening position
  • Pioneer VSX-D814-S | Operating Instructions - Page 49
    of 0.1 m to 9.0 m). • When SB SW (VSX-D814 only) or SB is selected in the surround back speaker setting, the surround back speaker distance can't be set. Subwoofer distance setting • Default setting: 3 m Like your speakers, you should set the distance of the subwoofer accurately to hear sounds from
  • Pioneer VSX-D814-S | Operating Instructions - Page 50
    . • Use or to set the dynamic range control (OFF, MAX, or MID). • Use or to cycle through the possible dual mono settings. Lch1.Rch2 ch2 ch1 Component video input settings VSX-D714/D814 only Here you tell the receiver what components you have hooked up to the component video jacks on the back of
  • Pioneer VSX-D814-S | Operating Instructions - Page 51
    . For example, assigning input 1 to the default setting of input 2 automatically switches input 2 to OFF. SR+ control for Pioneer plasma displays VSX-D714/D814 only Make the following settings if you have connected a Pioneer plasma display to this receiver using an SR+ cable. Note that the number
  • Pioneer VSX-D814-S | Operating Instructions - Page 52
    receiver with a numbered video input on the plasma display. For example, VIDEO:4 matches the VIDEO input with video input 4 on the plasma display. • You must complete the Speaker setting on page 46 before using the MCACC setup. Manually calibrating your listening area (MCACC) VSX-D714/D814 only
  • Pioneer VSX-D814-S | Operating Instructions - Page 53
    the STANDARD or ADVANCED SURROUND modes. L C SW LS R RS SB • If you don't hear a test tone from one of your speakers, please refer to Speaker setting on page 46 and (VSX-D714/D814 only) Surround back speaker setting on page 46 to make sure you have correctly specified your speaker setup. 53 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 54
    tones to set up your speaker system will overwrite any previous settings you had for the STANDARD or ADVANCED SURROUND modes. Using the SR+ mode with a Pioneer plasma display VSX-D714/D814 only When connected using an SR+ cable, a number of features become available to make using this receiver with
  • Pioneer VSX-D814-S | Operating Instructions - Page 55
    Setting up the receiver 06 • If you disconnect the SR+ cable or switch the plasma display off while SR+ is on, the receiver will automatically revert to SR+ OFF. • SR+ ERR shows in the display if no SR+ connection is detected (for example, the cable isn't connected). English
  • Pioneer VSX-D814-S | Operating Instructions - Page 56
    . The receiver will start searching for the next station, stopping when it has found one. Repeat to search for other stations. Manual tuning To you can simply enter the frequency directly using the number buttons on the remote control. 1 Press the TUNER button to select the tuner. 2 Use the BAND
  • Pioneer VSX-D814-S | Operating Instructions - Page 57
    When saving an FM frequency, the MPX setting (see page 56) is also stored. Use the front panel controls to store station presets. / SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP DIGITAL IN VIDEO INPUT S-VIDEO VIDEO L AUDIO R ENTER MULTI JOG MASTER VOLUME
  • Pioneer VSX-D814-S | Operating Instructions - Page 58
    . • Use the MULTI JOG dial (front panel) or the ST +/- buttons (remote) to select characters. • Press ENTER to confirm a character. If no character is setting: 1 Switch the receiver into standby. 2 On the front panel, press STANDBY/ ON while you press and hold the BAND (VSX-D714/D814) / CLASS (VSX
  • Pioneer VSX-D814-S | Operating Instructions - Page 59
    have no effect on the recorded signal. ADVANCED STEREO/ STANDARD SURROUND DIRECT SIGNAL MIDNIGHT/ SELECT LOUDNESS SPEAKERS SB CH MODE MULTI JOG TONE QUICK SETUP LISTENING MODE PUT ATT FL DIMMER DIGITAL IN VIDEO INPUT S-VIDEO VIDEO L AUDIO R * Illustrations show the VSX-D814 model 59 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 60
    remote control. The buttons can be set to control the following components: Selecting preset codes directly DVD/LD MULTI CONTROL TV / SAT DVR/VCR TV CONT CD CD-R/TAPE TUNER RECEIVER Button Controllable Components DVD/LD: DVD or LD player TV/SAT: TV or Satellite tuner DVR/VCR: Digital Video
  • Pioneer VSX-D814-S | Operating Instructions - Page 61
    method above. 4 Repeat steps 2 through 3 to try a different code, or to enter a code for another component you want to control. 5 When you're done, press RECEIVER. Programming signals from other remote controls VSX-D814 only If the preset code for your component is not available, or the available
  • Pioneer VSX-D814-S | Operating Instructions - Page 62
    . • Certain buttons represent operations that cannot be learned from other remote controls. These include: RECEIVER , the MULTI CONTROL buttons, RECEIVER CONTROL and MASTER VOLUME buttons. Erasing all of your programmed settings VSX-D814 only This erases all of the buttons you have programmed (in
  • Pioneer VSX-D814-S | Operating Instructions - Page 63
    Controls for TVs This remote control can control components after entering the proper codes or teaching the receiver the commands (see Setting the remote to control as the AUDIO button. Cable TV/Satellite TV/TV/ DTV GUIDE Use as the GUIDE button for navigating. Cable TV/Satellite TV/DTV Use as
  • Pioneer VSX-D814-S | Operating Instructions - Page 64
    to hook up to this system assign it to the TV CONT MULTI CONTROL button. If you have two TVs, assign the main TV to the TV CONT button. Controls for other components This remote control can control these components after entering the proper codes or teaching the receiver the commands (see Setting
  • Pioneer VSX-D814-S | Operating Instructions - Page 65
    Controlling the rest of your system 09 English Italiano Français Deutsch Nederlands Español Button (s) Function Components Hold down for fast reverse playback. CD/MD/CD-R/VCR/DVD/LD/ DVR player/Cassette deck Stops playback (on some models . VCR Displays the setup screen for DVR players GUIDE
  • Pioneer VSX-D814-S | Operating Instructions - Page 66
    the rest of your system Preset Code List (VSX-D514/D714) You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model that you are using. There are
  • Pioneer VSX-D814-S | Operating Instructions - Page 67
    Controlling the rest of your system 09 MD Manufacturer Code SONY 901 KENWOOD 903 SHARP 902 TEAC 904 ONKYO 905 DENON 906 PIONEER 900, 907 English Italiano Français Deutsch Nederlands Español 67 En
  • Pioneer VSX-D814-S | Operating Instructions - Page 68
    Code List (VSX-D814) You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model ZENITH 5163, 5164 VCR Manufacturer Code PIONEER 3001, 3002, 3003, 3004,
  • Pioneer VSX-D814-S | Operating Instructions - Page 69
    English Italiano Français Deutsch Nederlands Español Controlling the rest of your system 09 JC PENNY 3064, SIEMENS 6039, 6040 SONY 6041 TOSHIBA 6042, 6043 TOCOM 6044 ZENITH 6045, 6046 CD/CD-R Manufacturer Code PIONEER 7001, 7002 DENON 7003, 7004, 7005 FISHER 7006, 7007 JVC 7008, 7009, 7010, 7011
  • Pioneer VSX-D814-S | Operating Instructions - Page 70
    trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. Problem to Connecting up on page 14). • Press MUTE on the remote control to turn muting off. • Adjust the MASTER VOLUME. No image
  • Pioneer VSX-D814-S | Operating Instructions - Page 71
    page 52 to check the speaker levels. • Connect the speakers properly (refer to page 20). No sound from surround back speakers (VSX-D714/ D814 only). • Refer to Surround back speaker setting on page 46 to check the surround back speaker settings. • Refer to Manually calibrating your listening area
  • Pioneer VSX-D814-S | Operating Instructions - Page 72
    speakers. player during playback, noise is output. Can't operate the remote control. • Replace the batteries (refer to page 5). • Operate within 7 m, 30° of the remote reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver on. 2
  • Pioneer VSX-D814-S | Operating Instructions - Page 73
    surround) Front . . . . 100 W per channel (1kHz, 1.0%, 8 Ω) Center 100 W (1kHz, 1.0%, 8 Ω) Surround 100 W per channel (1kHz, 1.0%, 8 Ω) Surround Back. . . . . . 100 W (1kHz, 1.0 %, 8 Ω) (VSX-D814 , CD-R/TAPE/MD, DVD/LD, TV/SAT 79 dB Video Section Input (Sensitivity/Impedance) DVR/VCR, DVD/LD, TV
  • Pioneer VSX-D814-S | Operating Instructions - Page 74
    and UK 3-pin type) VSX-D814-S (silver model 4 (Round 2-pin type, flat blade 2-pin type, UK 3-pin type and Australian type) Power plug adaptor (VSX-D514/D714/D814-K only 1 J-shape plug (VSX-D514/D714/D814-K only). . . 1 These operating instructions 1 • Specifications and the design are subject
  • Pioneer VSX-D814-S | Operating Instructions - Page 75
    ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-D514
VSX-D714
VSX-D814
Operating Instructions