Poulan 1981-10 User Manual

Poulan 1981-10 Manual

Get Poulan 1981-10 PDF manuals and user guides View all Poulan 1981-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan 1981-10 manual content summary:

  • Poulan 1981-10 | User Manual - Page 1
    Fa Poutan Micro XXV Read Special SAFETY CENTER SPREAD each time you use your MICRO 25 CHAIN SAW OPERATOR'S MANUAL K BEAIRD-POULAN Division EmerSon Electric Co. / WEED EATER 5020 Flournoy-Lucas Road Shreveport, Louisiana 71109
  • Poulan 1981-10 | User Manual - Page 2
    . Adjusting Chain Fueling Bar.& Chain Oil Starting - Good Performance SAFETY CENTER SPREAD Types of Cutting Adjusting Carburetor Air Filter Sharpening Chain & Guide Bar Maint. Starter Rope PAGE 2 3 4 5 6 7 8-9 10-11 12.13 13 14 15 2 Read SAFETY CENTER SPREAD FREQUENTLY KICKBACK may happen when
  • Poulan 1981-10 | User Manual - Page 3
    .023 to .027" IGNITION Solid State MODULE AIR GAP FUEL MIX .008 to .014" (16:1) '/: Pt. Oil to 1 Gal. Reg. Gasoline OILER Automatic only GUIDE BAR 10" Control TipTM CHAIN Low Profile 3/8 Pitch 40 Drive Links MUFFLER Spark Arresting 12" SAW 2.0 Cu. In. Champion CJ8 .023 to .027" Solid
  • Poulan 1981-10 | User Manual - Page 4
    and chain . • Adjust the chain. FOR MIXING FUEL AND ADDING CHAIN OIL: You will need the proper fuel mixture, (see the fueling section of this manual, page 6), and, bar and chain lube or clean SAE 30 oil. ATTACHING THE HAND GUARD The hand guard helps prevent the hand from coming in
  • Poulan 1981-10 | User Manual - Page 5
    turning hex wrench counterclockwise. Remove small screw in back. 5. Making sure the guide bar is still flat against the side of the saw and the chain is still set in easily at the tip, pull the chain forward and let the groove guide the chain around the tip. A JUSTING SCR 6. Holding the tip of the
  • Poulan 1981-10 | User Manual - Page 6
    during saw operation, your oil supply is adequate. If you are using less oil and the oil tank is full, the oil hole on the guide bar might be blocked. Remove the bar clamp and bar and chain. Clear the oil hole in the bar anc replace the bar, chain, and
  • Poulan 1981-10 | User Manual - Page 7
    STARTING YOUR CHAIN SAW IMPORTANT: Make sure you have read and understand the entire safety center spread and the information on kickback (pg. 2) before starting or using your chain saw. Now, move away from the area in which you fueled your saw. Make sure you are on solid footing. Make sure the saw
  • Poulan 1981-10 | User Manual - Page 8
    sharp and at proper tension. Carry the chain saw with the engine stopped, the guide bar and chain covered and to the rear, and the muffler away from your mixture. rules, precautions, and operating instructions found in this manual. Allchain saw service other than the items listedin the operator
  • Poulan 1981-10 | User Manual - Page 9
    handle. Do not let the nose of the guide bar contact a log, branch, the ground, or motion of the guide bar which occurs when the saw chain at the nose of the guide bar contacts an from children. Follow manufacturer's sharpening and maintenance instructions for the saw chain. Always do your cutting
  • Poulan 1981-10 | User Manual - Page 10
    TYPES OF CUTTING for the occasional chain saw user There are several types of wood cutting you can do successfully and safely. Please read the Safety Center Spread for safe preparation of your saw and your work area, and for safe operation of the saw. If the weather is bad delay cutting until it
  • Poulan 1981-10 | User Manual - Page 11
    slowly, watching out for branches that are bent or under pressure, and for supporting limbs. BE ALERT FOR SPRINGBACK - the release of tension a branch or upside down to undercut. Position If saw becomes wedged in a log, the guide bar under the log and exert light pressure don't try to force it out
  • Poulan 1981-10 | User Manual - Page 12
    additional adjustments. PRELIMINARY: stop the engine. Be sure you have fresh fuel mix at the proper gasoline/oil ratio (see mixing instructions), and a screwdriver. I'PHOKE:SHUTTER. COUNTERCLOCKWISE 1. Remove the carburetor cover by loosening and removing the 2 screws on either side of the choke
  • Poulan 1981-10 | User Manual - Page 13
    the saw runs smoothly. CLEANING AIR FILTER 9. When you have completed these adjusments, recheck for proper idle mixture screw setting per instructions in views No. 5, 6, and 7. Check for acceleration. If there is a slight hesitation, turn the low speed mixture screw 1/16 turn counterclockwise
  • Poulan 1981-10 | User Manual - Page 14
    Your Poulan dealer has everything listed. You will also need a vise to hold the guide bar as you sharpen the chain. GAUGIT DEPTH GAUGE 1. Adjust the tension as tightly as can and still be able to move the chain around the bar. Place guide bar in a vise, clamping the center of the bar. 2. Sharpen
  • Poulan 1981-10 | User Manual - Page 15
    STARTER ROPE MAINTENANCE Repairing the recoil starter rope requires a certain degree of mechanical skill. You may decide to let your dealer handle this procedure. If you do try the procedure and the pulley spring pops out, take the unit to your dealer. SAFETY CENTER SPREAD -.1FREQUENTLY-1,',:t: 1.
  • Poulan 1981-10 | User Manual - Page 16
    (s). Your dealer can keep you informed about improvements in our products as they are placed on the market also. Parts and repair service are not available directly from BeairdPoulan/Weed Eater, Division Emerson Electric Co. BEAIRD-POULAN/ WEED EATER Division Emerson Electric Co. \4 34/.... Attn
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Fa
Poutan
Micro
XXV
Read
Special
SAFETY
CENTER
SPREAD
each
time
you
use
your
MICRO
25
BEAIRD-POULAN
/
WEED
EATER
Division
EmerSon
Electric
Co.
K
5020
Flournoy
-Lucas
Road
Shreveport,
Louisiana
71109
CHAIN
SAW
OPERATOR'S
MANUAL