Home » Poulan Manuals » Lawn & Garden » Poulan 2250 » Manual Viewer

Poulan 2250 User Manual

Poulan 2250 Manual

Get Poulan 2250 PDF manuals and user guides

View all Poulan 2250 manuals

Add to My Manuals
Save this manual to your list of manuals

Poulan 2250 manual content summary:

Poulan 2250 | User Manual - Page 1
, no devuelva el aparato al lugar de compra. Veuillez ne pas retourner l'outil au détaillant. 1--800--554--6723 www.poulan.com Instruction Manual Manual de Instrucciones Manuel d'Instructions 2250 / 2450 / 2550 / 2550 SE / 2555 For Occasional Use Only WARNING: Read and follow all Safety Rules and
Poulan 2250 | User Manual - Page 2
brake for the bar and chain combination on the label. SAFETY RULES WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. Because a chain
Poulan 2250 | User Manual - Page 3
, refer to CARBURETOR ADJUSTMENTS. S Never modify your saw in any way. S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fasteners securely tightened. S Use only PoulanR accessories and replacement parts as recommended. HANDLE FUEL WITH CAUTION
Poulan 2250 | User Manual - Page 4
to help reduce the hazard of kickback; however, such features will not totally eliminate this danger. As a chain saw user, do not rely only on safety devices. You must follow all safety precautions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result
Poulan 2250 | User Manual - Page 5
chain brake and resulting kick angle of saw. In all cases lower CKA values represent a safer operating environment for the user. The following guide bar and chain combinations meet kickback requirements of CSA Z62.1, Z62.3, & ANSI B175.1 when used on saws listed in this manual. Use of bar and chain
Poulan 2250 | User Manual - Page 6
below. Inside view of Chain Brake Adjustment located on Chain Brake 4. Turn the adjusting screw by hand counterclockwise until the adjusting pin just touches the stop. This should allow the pin to be near the correct position. 5. Slide guide bar behind clutch drum until guide bar stops against
Poulan 2250 | User Manual - Page 7
chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned. 12. Install chain brake nuts and finger tighten only. Once the chain is tensioned, you will need to tighten chain brake nuts. CHAIN
Poulan 2250 | User Manual - Page 8
ON/STOP Switch Primer Bulb Bar Oil Fill Cap Cylinder Cover Throttle Rear Lockout Handle Starter Housing Adjusting Screw Fuel Mix Fill Cap Chain Direction of Travel Throttle Trigger Choke/ Fast Idle Lever Chain Brake Chain Brake Nuts Guide Bar Chain Catcher ON/STOP SWITCH CHAIN BRAKE The ON
Poulan 2250 | User Manual - Page 9
and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for additional information. WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CARBURETOR ADJUSTMENT within this manual. Avoid
Poulan 2250 | User Manual - Page 10
the TROUBLESHOOTING TABLE or call 1-800-554-6723. CHAIN BRAKE WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part
Poulan 2250 | User Manual - Page 11
If you run the saw at full throttle without a cutting load, unnecessary wear can occur to the chain, bar, etc. If the tree makes contact with any utility line, the utility company should be notified immediately. S Carefully the opposite side of tree, the tree will tend to fall into the notch. NOTE:
Poulan 2250 | User Manual - Page 12
trees that may be poorly supported. When a tree doesn't cut. To avoid kickback and chain damage, do not use a side of log BUCKING WITHOUT A SUPPORT S Overcut through 1/3 of the BUCKING USING A LOG OR SUPPORT STAND S Remember your first second cut. Using a log for support 2nd Cut 1st Cut 1st Cut
Poulan 2250 | User Manual - Page 13
spark plug before performing maintenance except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level . . . . Before each use Bar lubrication Before each use Chain
Poulan 2250 | User Manual - Page 14
screen if breaks are found. 5. Replace any broken or cracked muffler parts. 6. Reinstall diffuser and spark arrestor screen assembly with round holes facing up. 7. Reinstall muffler cover and 2 screws. Tighten securely. CARBURETOR ADJUSTMENT WARNING: The chain will be mov- ing during most of
Poulan 2250 | User Manual - Page 15
the repair parts list or on the decal located on the chain saw. CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener. IGNITION TIMING Ignition timing is fixed and nonadjustable. SPARK PLUG
Poulan 2250 | User Manual - Page 16
fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. Engine will not idle properly. 1. Carburetor requires adjustment. 2. Crankshaft seals worn. 1. See "Carburetor Adjustment" in the Service and Adjustments
Poulan 2250 | User Manual - Page 17
PRODUCTS, INC., approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be pro- vided without charge to the owner if the part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up to
Poulan 2250 | User Manual - Page 18
The information on the product label indicates which standard your engine is certified. Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA. This engine is certified to be emissions compliant for the following use: Moderate (50 hours) Intermediate (125 hours) Extended (300 hours) 18