Home » Poulan Manuals » Lawn & Garden » Poulan 2550T » Manual Viewer

Poulan 2550T User Manual

Poulan 2550T Manual

Get Poulan 2550T PDF manuals and user guides

View all Poulan 2550T manuals

Add to My Manuals
Save this manual to your list of manuals

Poulan 2550T manual content summary:

Poulan 2550T | User Manual - Page 1
. Por favor, no devuelva el aparato al lugar de compra. Veuillez ne pas retourner l'outil au détaillant. 1--800--554--6723 www.poulan.com Instruction Manual Manual de Instrucciones Manuel d'Instructions 2550T ESPAÑOL For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating
Poulan 2550T | User Manual - Page 2
label. SAFETY RULES WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. Because a chain saw is a high-speed woodcutting tool, special
Poulan 2550T | User Manual - Page 3
, refer to CARBURETOR ADJUSTMENTS. S Never modify your saw in any way. S Keep the handles dry, clean, and free of oil or fuel mixture. S Keep fuel and oil caps, screws, and fasteners securely tightened. S Use only PoulanR accessories and replacement parts as recommended. HANDLE FUEL WITH CAUTION
Poulan 2550T | User Manual - Page 4
is in a straight line with your right hand on the rear handle when making bucking cuts. Never reverse right and left hand positions for any type of cutting. S a chain saw user, do not rely only on safety devices. You must follow all safety precautions, instructions, and maintenance in this manual to
Poulan 2550T | User Manual - Page 5
TO AVOID KICKBACK. Reduced--kickback guide bars and low--kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kickback chain and bar as original equipment. Repairs on a chain brake should be made by an authorized servicing dealer. Take your unit to
Poulan 2550T | User Manual - Page 6
to be equipped with a spark arresting screen. If you operate a chain saw in a state or locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the SERVICE section for maintenance of
Poulan 2550T | User Manual - Page 7
turn clockwise. Adjusting Screw Chain Brake Nuts Guide Bar Adjusting Screw -- 1/4 Turn S Lift up the tip of the bar and securely tighten the chain brake nuts with the bar tool. S Recheck chain tension. Chain Brake Nuts WARNING: If the saw is operated with a loose chain, the chain could jump
Poulan 2550T | User Manual - Page 8
Bar Oil Fill Cap Cylinder Cover Throttle Rear Lockout Handle Starter Housing Adjusting Screw Fuel Mix Fill Cap Chain Direction of Travel Throttle Trigger Choke/ Fast Idle Lever Chain Brake Chain Brake Nuts Guide Bar Chain Catcher ON/STOP SWITCH CHAIN BRAKE The ON/STOP SWITCH is used to stop
Poulan 2550T | User Manual - Page 9
run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for additional information. WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CARBURETOR ADJUSTMENT within this manual. Avoid contact with
Poulan 2550T | User Manual - Page 10
the TROUBLESHOOTING TABLE or call 1-800-554-6723. CHAIN BRAKE WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part
Poulan 2550T | User Manual - Page 11
made. Plan a clear retreat path to the rear and diagonal to the line of fall. Plan a clear retreat path FELLING LARGE TREES (6 inches (15 before making the notch. If using saw to remove buttress roots, keep saw chain from contacting ground to prevent dulling of the chain. NOTCH CUT AND FELLING THE
Poulan 2550T | User Manual - Page 12
poorly supported. When a tree doesn't fall completely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor. cutting by pulling out exposed and cleared logs first. TYPES OF CUTTING USED FOR BUCKING WARNING: If saw becomes pinched or hung in a log, don't try
Poulan 2550T | User Manual - Page 13
spark plug before performing maintenance except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level . . . . Before each use Bar lubrication Before each use Chain
Poulan 2550T | User Manual - Page 14
screen if breaks are found. 5. Replace any broken or cracked muffler parts. 6. Reinstall diffuser and spark arrestor screen assembly with round holes facing up. 7. Reinstall muffler cover and 2 screws. Tighten securely. CARBURETOR ADJUSTMENT WARNING: The chain will be mov- ing during most of
Poulan 2550T | User Manual - Page 15
the repair parts list or on the decal located on the chain saw. CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener. IGNITION TIMING Ignition timing is fixed and nonadjustable. SPARK PLUG
Poulan 2550T | User Manual - Page 16
fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. Engine will not idle properly. 1. Carburetor requires adjustment. 2. Crankshaft seals worn. 1. See "Carburetor Adjustment" in the Service and Adjustments
Poulan 2550T | User Manual - Page 17
PRODUCTS, INC., approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be pro- vided without charge to the owner if the part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up to
Poulan 2550T | User Manual - Page 18
The information on the product label indicates which standard your engine is certified. Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA. This engine is certified to be emissions compliant for the following use: Moderate (50 hours) Intermediate (125 hours) Extended (300 hours) 18