Poulan CHDR500D User Manual

Poulan CHDR500D Manual

Get Poulan CHDR500D PDF manuals and user guides View all Poulan CHDR500D manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan CHDR500D manual content summary:

  • Poulan CHDR500D | User Manual - Page 1
    WI • Assembly • Operation • Customer Responsibilities • Service and Adjustments • Storage • Troubleshooting • Repair Parts For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 Poulan 168499 2.1.99 TR PRINTED IN U.S.A.
  • Poulan CHDR500D | User Manual - Page 2
    Read the Owner's Manual carefully. Be Vibration is generally a warning of trouble. • Stop the engine (motor the engine and make certain all moving parts have stopped. Disconnect the spark plug wire enclosure. • Always refer to the operator's guide instructions for important details if the tiller is
  • Poulan CHDR500D | User Manual - Page 3
    . Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble
  • Poulan CHDR500D | User Manual - Page 4
    3,13-15 4 5-7 8-12 MAINTENANCE SCHEDULE SERVICE & ADJUSTMENTS STORAGE TROUBLESHOOTING REPAIR PARTS-TILLER 13 15-18 19 20 21-27 been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been
  • Poulan CHDR500D | User Manual - Page 5
    exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller, all parts and hardware you POSITION (See Fig. 1) Nhen right or left hand is mentioned in this manual, it means when you are in the operating position (standing jehind tiller handles).
  • Poulan CHDR500D | User Manual - Page 6
    down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loosely assemble locknut (See Fig. 5). • Insert pivot bolt in front part of plate and tighten. • Cut down remaining corners of carton and lay panels flat. • Lower the handle assembly. Tighten nut on carriage bolt bolt
  • Poulan CHDR500D | User Manual - Page 7
    tire pressure to 20 PSI (1.4 kg/cm2). HANDLE HEIGHT • Handle height may be adjusted to better suit operator. (See "TO ADJUST HANDLE HEIGHT" in the Service and Adjustments section of this manual). 7
  • Poulan CHDR500D | User Manual - Page 8
    OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their
  • Poulan CHDR500D | User Manual - Page 9
    OPERATION WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety
  • Poulan CHDR500D | User Manual - Page 10
    capacity see "PRODUCT SPECIFICATIONS" on page 3 of this manual. All oil must meet A.P.I. Service Classification SF, SG or SH. • For cold weather damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer
  • Poulan CHDR500D | User Manual - Page 11
    CARBURETOR" in the Service and Adjustnents section of this manual. DOTE: If engine does not start, see troubleshooting points. SPARK PLUG shaft with shear pins (See "TINE REPLACEMENT" in the Service and Adjustments section of this manual). If the tiller is unusually overloaded or jammed, the
  • Poulan CHDR500D | User Manual - Page 12
    OPERATION CULTIVATING Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Best digging depth is 1" to 3" (2.5-7.5 cm). Lower the
  • Poulan CHDR500D | User Manual - Page 13
    value from the warranty. the operator must laintain tiller as instructed in this manual. ;ome adjustments will need to be made periodically to roperly maintain your tiller. di adjustments in the Service and Adjustments section of pis manual should be checked at least once each eason. Once a year
  • Poulan CHDR500D | User Manual - Page 14
    ENGINE OIL LEVEL" in the Operation section of this manual. 'Ns OIL DRAIN PLUG, AIR CLEANER (See Fig. 20) Service air cleaner cartridge every twenty-five hours, more often using a stiff-bristled brush. • Remove blower housing and clean as necessary. • Keep cylinder fins free of dirt and
  • Poulan CHDR500D | User Manual - Page 15
    first. Spark plug type and gap setting is shown in "PRODUCT SPECIFICATIONS" on page 3 of this manual. .TRANSMISSION Your transmission is sealed and will only require lubrication if serviced. CLEANING • Clean engine, wheels, finish, etc. of all foreign matter. • Keep finished surfaces and wheels
  • Poulan CHDR500D | User Manual - Page 16
    SERVICE AND ADJUSTMENTS TINE REPLACEMENT (See Figs. 24, 25 and 26) a CAUTION: Tines are sharp. Wear gloves or other protection when han- dling tines. A badly worn
  • Poulan CHDR500D | User Manual - Page 17
    SERVICE AND ADJUSTMENTS TO REMOVE BELT GUARD (See Fig. 27) NOTE: For ease of pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES. • Check belt adjustment as described below. • Replace belt guard. • Reposition wheel and replace clevis pin and
  • Poulan CHDR500D | User Manual - Page 18
    , altitude or load. If the carburetor does need adjustment, see engine manual. High speed stop is factory adjusted. Do not adjust or damage may THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO
  • Poulan CHDR500D | User Manual - Page 19
    instructions in the Service and Adjustments section of this manual). Lubricate as shown in the Customer Responsibilities section of this manual. Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts dirt in your gasoline will cause problems. • If possible, store your
  • Poulan CHDR500D | User Manual - Page 20
    PROBLEM TROUBLESHOOTING POINTS CAUSE CORRECTION ,4. Will not start 1. Out of fuel. 2. Engine not "CHOKED" screen. 11. Clean/replace muffler. 12. Make necessary adjustments. 13. Contact an authorized service center/department. 1. Check oil level/change oil. 2. Clean engine air screen. 3. Clean
  • Poulan CHDR500D | User Manual - Page 21
    Carriage 3/8-16 x 1 Gr. 5 Clip, Hairpin Lock, Handle Nut 3/8-16 Washer 13/32 x 1 x 11 Ga. Lever, Lock, Handle Handle 14 13 7 'N> . '1 / . 8 ,o „ 1 9 12 18 KEY PART NO. NO. 14 159232 15 145821 17 102604X 18 150696 21 159227 22 150744 24 73731000 25 127012X 26 146480 27 10040500 28 73800500
  • Poulan CHDR500D | User Manual - Page 22
    14 • 33 32 31 0 20 30 43 5 4 is 16 0 18 19 22 28 3 KEY PART NO. NO. 1 73510500 2 10040600 3 73220600 4 165710 5 154734 6 110111X 7 72110404 8 8700J 9 Clip, Hairpin Guard, Belt Belt, V 4 2 40 2 23 15 24 KEY PART NO. NO. 28 104679X 29 12000032 30 159229 31 102384X 32 102141X 33 74760616
  • Poulan CHDR500D | User Manual - Page 23
    7 4497H 8 126875X DESCRIPTION Nut, Keps 5/16-18 Bracket, Reinforcement Bolt, Hex 5/16-18 x 1-1/2 Counter Weight, R.H. Washer, Lock 3/8 Nut, Hex 3/8-16 Clip, Hairpin Rivet, Drilled KEY PART NO. NO. DESCRIPTION 9 102190X Tire 150750 Rim 795R Tire Valve 10 Engine, Briggs Model 137202 (Order
  • Poulan CHDR500D | User Manual - Page 24
    49 --- y 44 48 53 73 36 24 50 25 ig( 24 53 25 52 5 44 KEY PART NO. NO. 1 165728 2 165729 3 161963 4 5020J 5 1370H 6 137335 7 145101 8 4895H 9 Needle Shaft, Reverse Idler Washer, Lock 7/16 Nut, Hex 7/16-20 KEY PART NO. NO. DESCRIPTION 27 143009 28 106390X 29 102134X 30 150737 31 143008
  • Poulan CHDR500D | User Manual - Page 25
    12 7t- 11 11 10 16 25 27 23 24, 23 12_. 16 26 16 blV ) 1). 22 .- 11 20 29 15 16 21 19
  • Poulan CHDR500D | User Manual - Page 26
    7 10040600 DESCRIPTION Tine, Outer, L.H. Clevis Pin Tine, Inner, L.H. Retainer, Spring Assembly, Hub and Plate, L.H. Nut, Hex 3/8-24 Washer, Lock 3/8 KEY PART NO. NO. 8 74610616 9 4460J 10 132728 11 6555J DESCRIPTION Bolt, Hex 3/8-24 x 1 Tine, Outer, R.H. Assembly, Hub and Plate, R.H. Tine, Inner
  • Poulan CHDR500D | User Manual - Page 27
    DESCRIPTION Decal, Logo Decal, Description Decal, Logo Decal, Instruction, Tilling Decal, Hand Placement Decal, Shift Indicator Decal, Pnl Cntrl Reverse Decal, Briggs & Stratton Decal, Warning, Rotating Tines Decal, 5 HP Decal, Warning Till . Manual, Owner's (English) Manual, Owner's (French)
  • Poulan CHDR500D | User Manual - Page 28
    Poulan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
TD
luoT
U
OWNER'S
MANUAL
MODEL
NO.
CHDR5OOD
5
HP
17
Inch
Tiller
WI
•
Assembly
•
Operation
•
Customer
Responsibilities
•
Service
and
Adjustments
•
Storage
•
Troubleshooting
•
Repair
Parts
For
Parts
and
Service,
contact
our
authorized
distributor:
call
1-800-849-1297
For
Technical
Assistance:
call
1-800-829-5886
Poulan
168499
2.1.99
TR
PRINTED
IN
U.S.A.