Poulan PR827ES User Manual

Poulan PR827ES Manual

Get Poulan PR827ES PDF manuals and user guides View all Poulan PR827ES manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan PR827ES manual content summary:

  • Poulan PR827ES | User Manual - Page 1
    IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: PR827ES SNOW THROWER WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. Always Wear Eye Protection During Operation 437139 06.23.10 TH Printed in the
  • Poulan PR827ES | User Manual - Page 2
    the snow thrower. containers on the ground, away from your vehicle, before filling. 4. If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. (e) When practical, remove gas-powered equipment Vibration is generally a warning of trouble. from
  • Poulan PR827ES | User Manual - Page 3
    technicians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the "SAFETY RULES". SERIAL NUMBER DATE OF PURCHASE THE MODEL AND SERIAL NUMBERS WILL BE FOUND
  • Poulan PR827ES | User Manual - Page 4
    (1) SHOULDER BOLT 1/4-20 (179829) (1) SPRING (184505) ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly
  • Poulan PR827ES | User Manual - Page 5
    assembly of the chute rotator head to snow thrower and making adjustments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to
  • Poulan PR827ES | User Manual - Page 6
    5 and 6) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower
  • Poulan PR827ES | User Manual - Page 7
    BOLT 1/4-20 LOCKNUT SPRING CHUTE DEFLECTOR HOOK BETWEEN HEX NUTS ON CHUTE ROTATER HEAD 5/16-18 CARRIAGE BOLT CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pressure is important for best
  • Poulan PR827ES | User Manual - Page 8
    adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. DANGER OR WARNING PRIMER FORWARD REVERSE READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS
  • Poulan PR827ES | User Manual - Page 9
    wrench. Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use. Electric start button - used for starting the engine. Recoil (auxiliary) starter handle - used for starting the engine. Primer - pumps additional fuel from the carburetor to the
  • Poulan PR827ES | User Manual - Page 10
    control whenever you are starting a cold engine. Do not use to start a warm engine. • To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage. TO CONTROL SNOW DISCHARGE (See Fig. 12) WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from
  • Poulan PR827ES | User Manual - Page 11
    restarting engine. • Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute. DISCHARGE CHUTE CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result
  • Poulan PR827ES | User Manual - Page 12
    to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 17) The engine on your snow thrower has been shipped from the factory already filled with oil
  • Poulan PR827ES | User Manual - Page 13
    path and moving slowly. • Keep engine clean and clear of snow during use. This will help air flow and extend engine life. • After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. • Clean the entire snow thrower thoroughly after each use and wipe
  • Poulan PR827ES | User Manual - Page 14
    warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of
  • Poulan PR827ES | User Manual - Page 15
    can cause contamination of the friction wheel and damage to the drive system of your snow thrower. ENGINE See engine manual. LUBRICATION Use only high quality detergent oil rated with API service classification SG-SL. Select the oil's SAE viscosity grade according to your expected operating
  • Poulan PR827ES | User Manual - Page 16
    and all moving parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. SNOW THROWER TO ADJUST SNOW THROWER HEIGHT See "TO ADJUST SKID PLATES" and "SCRAPER BAR" in the Operation section of this manual. CHUTE DEFLECTOR The
  • Poulan PR827ES | User Manual - Page 17
    - See "TO REMOVE BELT COVER" in this section of this manual. 4. REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft. 5. SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the
  • Poulan PR827ES | User Manual - Page 18
    HUB ENGINE See engine manual. CARBURETOR Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center
  • Poulan PR827ES | User Manual - Page 19
    , etc. Store in a clean, dry area. 1. Clean entire snow thrower (See "CLEANING" in the Maintenance section of this manual). 2. Inspect and replace belts, if necessary (See "TO REPLACE BELTS" in the Service and Adjustments section of this manual). 3. Lubricate as shown in the Maintenance section of
  • Poulan PR827ES | User Manual - Page 20
    TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM position. 6. Prime as instructed in the Operation section of this manual. 7. Wait a few ice and snow on and around fuel tank cap. 4. Clean or replace muffler. Engine idles or
  • Poulan PR827ES | User Manual - Page 21
    SERVICE NOTES 21
  • Poulan PR827ES | User Manual - Page 22
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) AUGER HOUSING / IMPELLER ASSEMBLY 5 15 14 4 11 6 11 16 12 13 11 3 12 10 11 7 8 17 1 9 37 2 9 9 33 37 32 34 30 31 31 29 28 26 27 36 20 21 22 23 25 35 24 23 22 21 18 19 2 (EXPLODED) 01.07.026-D NOTE:
  • Poulan PR827ES | User Manual - Page 23
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) AUGER HOUSING / IMPELLER ASSEMBLY KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO. 175321X431 427148 188909 427146 175322 178675X431 192199 405400 73800400
  • Poulan PR827ES | User Manual - Page 24
    PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) AUGER HOUSING / IMPELLER ASSEMBLY 1 3 (5x) 4 (5x) 2 01.07.002-A KEY NO. 1 2 3 4 PART NO. 404929X421 404932X431 72270505 155377 DESCRIPTION AUGER HOUSING 27 SCRAPER BAR CARRIAGE BOLT 5/16−18 X .625 NUT 5/16−18 2 3 1 1 2 KEY PART
  • Poulan PR827ES | User Manual - Page 25
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) AUGER HOUSING / IMPELLER ASSEMBLY 2 1 01.07.018-A KEY NO. 1 2 PART NO. 420495X431 420496X431 DESCRIPTION AUGER 27 LH AUGER 27 RH 4 4 01.11.001-B 3 2 3 KEY PART NO. NO. DESCRIPTION 1 174762X431 SKID PLATE LH 2 178777X431
  • Poulan PR827ES | User Manual - Page 26
    ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY. NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void
  • Poulan PR827ES | User Manual - Page 27
    WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY. NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27
  • Poulan PR827ES | User Manual - Page 28
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) HANDLES 4 4 3 2 01.08.004-B 3 4 4 3 3 KEY PART NO. NO. DESCRIPTION 1 419798X431 LOOP HANDLE LH 1 2 419799X431 LOOP HANDLE RH 3 74780524 SCREW 5/16−18 X 1.50 4 751153 NUT 5/16−18 1 2 4 KEY NO. 1 2 3 4 PART NO.
  • Poulan PR827ES | User Manual - Page 29
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) HANDLES 10 2 11 9 5 7 6 8 47 9 1 3 8 12 13 13 14 01.08.002-F 14 12 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 412683X431 424517X431 424516X431 412679X008 426918X008 412677 421613 169675 17060410 414280 414281 178899
  • Poulan PR827ES | User Manual - Page 30
    PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) HANDLES 2 10 10 1 3 8 9 4 KEY NO. 1 2 3 4 5 6 7 8 9 10 PART in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and
  • Poulan PR827ES | User Manual - Page 31
    PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) HANDLES 3 2 5 6 7 4 41 01.10.007-B 5 KEY NO. 1 2 3 4 5 6 7 PART NO inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower
  • Poulan PR827ES | User Manual - Page 32
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) DRIVE 42 EXPLODED 2 16 1 17 15 14 15 12 9 11 11 20 9 9 10 11 53 13 53 19 8 7 53 21 6 5 45 18 22 34 53 23 3 31 29 30 28 26 24 27 26 36 33 32 38 35 53 46 47 49 24 4 23 24 33 48 51
  • Poulan PR827ES | User Manual - Page 33
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) DRIVE KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. 198875 17501010 402685X421 17490508 57079 405485 198580 403097X008 402881 403096X431 191730 402856X008 416717X431 187101 700279 427542
  • Poulan PR827ES | User Manual - Page 34
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) DRIVE 5 6 1b 7 4 3 1b 6 1a 2 KEY PART NO. NO. DESCRIPTION 3 inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower
  • Poulan PR827ES | User Manual - Page 35
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) CHASSIS / ENGINE / PULLEYS 2 3 1 2 3 01.00.034-A KEY NO. - - 1 2 3 PART NO 418694X421 150406 428867 DESCRIPTION ENGINE, B&S (MODEL 12A114-1354-E8) FRAME BOLT 3/8-16 SCREW 5/16-18 X .750 1 KEY NO. 1 PART NO. 436146X421
  • Poulan PR827ES | User Manual - Page 36
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) CHASSIS / ENGINE / PULLEYS 23 22 14 24 21 20 11 14 21 13 20 12 14 15 6 7 10 8 19 18 17 16 5 4 3 9 1 2 01.21.003-C KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 408007 419744 423723X431 180523 426589 74780524 423990X431
  • Poulan PR827ES | User Manual - Page 37
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) CHASSIS / ENGINE / PULLEYS 1 KEY NO. 1 PART NO. 428684 DESCRIPTION COVER ASSEMBLY 01.21.013-B NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.)
  • Poulan PR827ES | User Manual - Page 38
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) WHEELS KEY PART NO. NO. DESCRIPTION 1 432335X428 WHEEL ASSEMBLY LH 2 432336X428 WHEEL ASSEMBLY RH 1 2 01-06-016-A NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment
  • Poulan PR827ES | User Manual - Page 39
    REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) BAG OF PARTS 3 2 01.14.003-B 4 6 5 7 8 9 10 1 12 11 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 198563 169675 180684X008 184505 179829 191730 72250505 751153 73800600 19131316 192090 73800400 DESCRIPTION POWER CORD RETAINER
  • Poulan PR827ES | User Manual - Page 40
    SNOW THROWER - - MODEL NUMBER PR827ES (96192004302) DECALS 1 4 1 3 KEY NO. 1 3 4 - - - PART NO. 181037 181035 181042 437139 437140 DESCRIPTION DECAL, DANGER DECAL, DANGER, DEFLECTOR DECAL, DANGER OWNER'S MANUAL, ENGLISH OWNER'S MANUAL, FRENCH NOTE: All component dimensions given in U.S. inches
  • Poulan PR827ES | User Manual - Page 41
    SERVICE NOTES 41
  • Poulan PR827ES | User Manual - Page 42
    SERVICE NOTES 42
  • Poulan PR827ES | User Manual - Page 43
    SERVICE NOTES 43
  • Poulan PR827ES | User Manual - Page 44
    does not apply to the engine or components parts thereof. Please refer to the and maintained in accordance with the instructions furnished. This Warranty does not apply Poulan Pro Customer Service Department 1030 Stevens Creek Road Augusta, GA 30907 USA In Canada contact: Poulan Pro, Customer Service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
OWNER'S MANUAL
MODEL NUMBER:
PR827ES
SNOW THROWER
Always Wear Eye Protection During Operation
IMPORTANT MANUAL
Do Not Throw Away
WARNING:
Read the Owner's Manual and
follow all Warnings and Safety
Instructions.
Failure to do so
can result in serious injury.
437139
06.23.10
TH
Printed in the U.S.A.