ProForm Fusion 1.7x Bench English Manual
ProForm Fusion 1.7x Bench Manual
 |
View all ProForm Fusion 1.7x Bench manuals
Add to My Manuals
Save this manual to your list of manuals |
ProForm Fusion 1.7x Bench manual content summary:
- ProForm Fusion 1.7x Bench | English Manual - Page 1
SERVICE DEPARTMENT DIRECTLY. CALL TOLL-FREE: 1-888-533-1333 Mon.-Fri., 6 a.m.-6 p.m. MST ON THE WEB: www.proformservice.com CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USERʼS MANUAL Visit our website at www.proform - ProForm Fusion 1.7x Bench | English Manual - Page 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 5 ADJUSTMENTS 8 EXERCISE GUIDELINES 9 PART LIST 10 EXPLODED DRAWING 11 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover PROFORM is a registered trademark of ICON IP, Inc. 2 - ProForm Fusion 1.7x Bench | English Manual - Page 3
. Do not use the dumbbell bench with more than 110 pounds of weight. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON - ProForm Fusion 1.7x Bench | English Manual - Page 4
cover of this manual). To avoid a registration fee for any service needed under warranty, you must register the dumbbell bench at www.proformservice.com/registration. Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Backrest Seat - ProForm Fusion 1.7x Bench | English Manual - Page 5
(18) M10 x 193mm Bolt (19) ASSEMBLY To hire an authorized service technician to assemble the dumbbell bench, call toll-free 1-800-445-2480. Before beginning assembly, carefully read the following information and instructions: • Assembly requires two persons. • Place all parts in a cleared area - ProForm Fusion 1.7x Bench | English Manual - Page 6
Frame (1) with two M10 x 15mm Screws (21) and two M10 Washers (23). 23 23 21 1 3. Orient the Deck (4) as shown, and press it onto the Frame (1). Next, attach the Seat Frame (5) to the Frame (1) with two M10 x 65mm Screws (20) and two M10 Washers (23). Hand tighten the Backrest Knob (11) into - ProForm Fusion 1.7x Bench | English Manual - Page 7
193mm Bolt (19). Insert the Bolt through the Backrest Frame (6) and the Seat Frame (5). Then, tighten an M10 Nylon Locknut (24) and an M10 Washer the weight plates. 8. Make sure that all parts are properly tightened before you use the dumbbell bench. Place a mat under the dumbbell bench to protect - ProForm Fusion 1.7x Bench | English Manual - Page 8
explains how to adjust the dumbbell bench. See the accompanying exercise guide to see the correct form for several exercises. Make sure that all parts are properly tightened each time you use the dumbbell bench. Replace any worn parts immediately. The dumbbell bench can be cleaned with a damp - ProForm Fusion 1.7x Bench | English Manual - Page 9
more sets rather than by using high amounts of weight. Weight Loss To lose weight, use a low amount of weight and increase the number of repetitions in each set. will leave you feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the correct form for - ProForm Fusion 1.7x Bench | English Manual - Page 10
Washer M10 Washer M10 Nylon Locknut Backrest Plate Seat Plate Userʼs Manual Hex Key Grease Packet Exercise Guide Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts. 10 - ProForm Fusion 1.7x Bench | English Manual - Page 11
EXPLODED DRAWING-Model No. PFBE1506.0 8 26 25 13 9 6 22 16 24 23 15 15 24 22 7 24 22 16 23 23 17 22 15 19 23 24 14 5 11 12 22 22 16 4 21 23 R1106A 10 24 2 23 18 23 1 24 10 10 23 20 3 10 11 - ProForm Fusion 1.7x Bench | English Manual - Page 12
assist you, be prepared to provide the following information: • the MODEL NUMBER of the product (PFBE1506.0) • the NAME of the product (PROFORM Fusion 1.7X dumbbell bench) • the SERIAL NUMBER of the product (see the front cover of this manual) • the KEY NUMBER and DESCRIPTION of the part(s) (see the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
Model No. PFBE1506.0
Serial No.
Write the serial number in the
space above for future reference.
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.proformservice.com
USERʼS MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal (Under Seat)
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!