ProForm Xp 580 Crosstrainer Treadmill User Manual - Page 19

Troubleshooting

Get ProForm Xp 580 Crosstrainer Treadmill PDF manuals and user guides View all ProForm Xp 580 Crosstrainer Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call the telephone number on the front cover of the manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. c Tripped Reset PROBLEM: The power turns off during use SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console. Reinsert the key into the console. d. If the treadmill still will not run, please see the front cover of the manual. PROBLEM: The displays of the console do not function properly SOLUTION: a. Remove the key from the console and UNPLUG THE a POWER CORD. Remove the three hood Screws (2). 2 Carefully pivot the Hood (41) off. 41 Locate the Reed Switch (63) and the Magnet (46) on the left side of the Pulley (47). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is 1/8 in. 47 about 1/8 in. (3 mm). If necessary, loosen the Screw (72), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the treadmill for 72 63 46 a few minutes to check for a correct speed reading. Top View 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
19
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call the telephone number on the
front cover of the manual.
PROBLEM:
The power does not turn on
SOLUTION:
a.
Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b.
After the power cord has been plugged in, make sure that the key is inserted into the console.
c.
Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
PROBLEM:
The power turns off during use
SOLUTION:
a.
Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b.
Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c.
Remove the key from the console. Reinsert the key into the console.
d.
If the treadmill still will not run, please see the front cover of the manual.
PROBLEM:
The displays of the console do not function properly
SOLUTION:
a.
Remove the key from the console and
UNPLUG THE
POWER CORD.
Remove the three hood Screws (2).
Carefully pivot the Hood (41) off.
Locate the Reed Switch (63) and the Magnet (46) on the
left side of the Pulley (47). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure that
the gap between the Magnet and the Reed Switch is
about 1/8 in. (3 mm).
If necessary, loosen the Screw
(72), move the Reed Switch slightly, and then retighten
the Screw. Reattach the Hood, and run the treadmill for
a few minutes to check for a correct speed reading.
Tripped
Reset
c
41
2
a
Top
View
46
72
63
1/8 in.
47