ProForm Xp 615 Trainer Treadmill English Manual - Page 8

Be Damaged When The Power Is

Get ProForm Xp 615 Trainer Treadmill PDF manuals and user guides View all ProForm Xp 615 Trainer Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (53) so the treadmill is more stable; do not fully fold the Frame yet. Remove and discard the two indicated bolts (A) and the shipping bracket (B). Attach a Base Pad (79) to the Base (80) in the location shown with a Base Pad Spacer (25) and an 1" Tek Screw (56). Then, attach another Base Pad (79) with only a 1" Tek Screw (56). Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4), and the shipping bracket (C) from the Base (80). Attach a Wheel (81) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the Wheel must turn freely. Discard the shipping bracket. 6. With the help of a second person, hold a Bolt Spacer (3) inside the lower end of the Left Upright (71). Insert a 3/8" x 4" Bolt (6) with a 3/8" Star Washer (9) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (3), 3/8" x 4" Bolt (6), and 3/8" Star Washer (9). Orient the Left Upright (71) and the Left Upright Spacer (73) as shown. Hold the Left Upright Spacer and the Left Upright against the Base (80). Finger tighten the 3/8" x 4" Bolts (6); do not fully tighten the Bolts yet. Press a Base Endcap (75) into the Base (80). With the help of a second person, tip the treadmill so that the Base (80) is flat on the floor. 7. Have a second person hold the console assembly near the Right Upright (72). Remove the wire tie from the Upright Wire (78). Connect the Upright Wire (78) to the console wire. See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Then, insert the connectors into the Right Upright (72). Set the console assembly on the Right Upright (72) and the Left Upright (not shown). Attach the console assembly with four 5/16" x 1" Bolts (5) and four 5/16" Star Washers (7); start all four Bolts and then tighten them. 5 A 79 56 B 80 53 4 25 81 56 79 C 8 6 6 71 73 39 75 3 80 7 Console Wire 78 7 5 72 Console Assembly 7 78 5 Wire Tie 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
8
5.
With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (53) so the treadmill is more stable;
do
not fully fold the Frame yet.
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
Attach a Base Pad (79) to the Base (80) in the
location shown with a Base Pad Spacer (25)
and an 1" Tek Screw (56). Then, attach another
Base Pad (79) with only a 1" Tek Screw (56).
Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (80).
Attach a Wheel (81) with the Bolt and the Nut
that you just removed.
Do not overtighten the
Nut; the Wheel must turn freely.
Discard the
shipping bracket.
7.
Have a second person hold the console assem-
bly near the Right Upright (72). Remove the wire
tie from the Upright Wire (78).
Connect the Upright Wire (78) to the console
wire.
See the inset drawing. The connectors
should slide together easily and snap into
place.
If they do not, turn one connector and try
again.
IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON.
Then, insert the connectors into
the Right Upright (72).
Set the console assembly on the Right Upright
(72) and the Left Upright (not shown). Attach the
console assembly with four 5/16" x 1" Bolts (5)
and four 5/16" Star Washers (7);
start all four
Bolts and then tighten them.
5
72
7
78
Console
Assembly
Console
Wire
Wire Tie
7
5
7
78
5
80
81
53
4
8
C
79
56
79
25
56
B
A
6.
With the help of a second person, hold a Bolt
Spacer (3) inside the lower end of the Left
Upright (71). Insert a 3/8" x 4" Bolt (6) with a
3/8" Star Washer (9) into the Left Upright and
the Bolt Spacer. Repeat this step with a second
Bolt Spacer (3), 3/8" x 4" Bolt (6), and 3/8" Star
Washer (9).
Orient the Left Upright (71) and the Left Upright
Spacer (73) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(80). Finger tighten the 3/8" x 4" Bolts (6);
do
not fully tighten the Bolts yet.
Press a Base Endcap (75) into the Base (80).
With the help of a second person, tip the tread-
mill so that the Base (80) is flat on the floor.
73
71
6
80
3
3
75
9
6