Pyle HTG237 Instruction Manual
Pyle HTG237 Manual
View all Pyle HTG237 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle HTG237 manual content summary:
- Pyle HTG237 | Instruction Manual - Page 1
- Pyle HTG237 | Instruction Manual - Page 2
allow flexibility in hosting several different speaker configurations. To achieve optimum performance, it is highly recommended that you read this Owners Manual before beginning installation. WARNING High powered audio systems in a vehicle are capable of generating "Live Concert" high levels of sound - Pyle HTG237 | Instruction Manual - Page 3
TABLE OF CONTENTS PLANNING YOUR SYSTEM 4 WIRING CONNECTION 5 PANEL LAYOUT 6, 7 CONTROL FUNCTIONS 8, 9 SPEAKER CONNECTION MONO CHANNEL 10-16 TROUBLE SHOOTING GUIDE 17 SPECIFICATION 18 WARNING 19 PLANNING YOUR SYSTEM Before beginning the installation, consider the following: 1. Do you plan to - Pyle HTG237 | Instruction Manual - Page 4
CONNECTING THE POWER CAUTION: AS A PRECAUTION, DISCONNECT THE POWER WIRE FROM THE BATTERY WHILE MAKING THE POWER AND GROUND CONNECTIONS TO THE AMPLIFIER. 4/8 GAUGE(Thicker if planning for additional Amplifiers) wire is recommended for both the power and ground wires 12 Gauge, for the remote turn-on - Pyle HTG237 | Instruction Manual - Page 5
PANEL LAYOUT HTG157 FRONT VIEW 1 9 2 6 4 38 HTG237 / HTG257 FRONT VIEW 19 2 4 4 6 8 HTG2100D FRONT VIEW 19 2 35 5 6 78 HTG447 FRONT VIEW 6 4 42 1 1 2 4 468 < 6 > - Pyle HTG237 | Instruction Manual - Page 6
PANEL LAYOUT HTG157 REAR VIEW 10 11 12 13 14 HTG237 / HTG257 REAR VIEW 10 11 12 13 14 HTG2100D REAR VIEW 10 11 12 13 14 HTG447 REAR VIEW 10 11 12 13 14 < 7 > - Pyle HTG237 | Instruction Manual - Page 7
CONTROL FUNCTIONS 1. RCA input jacks These RCA input jacks are for use with source units that have RCA or Line level outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high quality twisted pair cables is recommended to decrease the possibility of - Pyle HTG237 | Instruction Manual - Page 8
CONTROL FUNCTIONS 8. LED Will illuminate GREEN to indicate the amplifier is on and operating normally, and will be illuminated RED if the amplifier shuts down due to short circuit, DC offset, or overheating detected by on board protection circuitry 9. Auxiliary outputs The Auxiliary outputs offer - Pyle HTG237 | Instruction Manual - Page 9
System Diagrams MONO Channel System Design #1 HTG157 2-4 HTG2100D 2-4 < 10 > - Pyle HTG237 | Instruction Manual - Page 10
System Diagrams 2Channel System Design #1 HTG237 / HTG257 < 11 > - Pyle HTG237 | Instruction Manual - Page 11
System Diagrams 2Channel System Design #2 HTG237 / HTG257 < 12 > - Pyle HTG237 | Instruction Manual - Page 12
System Diagrams 2Channel System Design #3 HTG237 / HTG257 < 13 > - Pyle HTG237 | Instruction Manual - Page 13
System Diagrams 4Channel System Design #1 HTG447 < 14 > - Pyle HTG237 | Instruction Manual - Page 14
System Diagrams 4Channel System Design #2 HTG447 < 15 > - Pyle HTG237 | Instruction Manual - Page 15
System Diagrams 4Channel System Design #3 HTG447 1CH 4-8 Ohms WOOFER 4-8ohms 2CH 4-8 Ohms 3CH 4-8 Ohms < 16 > WOOFER 4-8ohms 4CH 4-8 Ohms - Pyle HTG237 | Instruction Manual - Page 16
TROUBLE SHOOTING GUIDE SYMPTOMS NO SOUND AMP NOT SWITCHING ON NO SOUND IN ONE CHANNEL AMP TURNING OFF MEDIUM/ HIGH VOLUME CHECK POINTS Is the power LED illuminated? - Pyle HTG237 | Instruction Manual - Page 17
WARNINGS Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care when to work near the gas tanks, lines, or hydraulic lines, and electrical wiring. Don't use power amplifier unmounted. Attach this system securely to the automobile to prevent damage, - Pyle HTG237 | Instruction Manual - Page 18
System Diagrams 4Channel System Design #1 HTG447 < 14 > - Pyle HTG237 | Instruction Manual - Page 19
System Diagrams 4Channel System Design #2 HTG447 < 15 > - Pyle HTG237 | Instruction Manual - Page 20
System Diagrams 4Channel System Design #3 HTG447 1CH 4-8 Ohms WOOFER 4-8ohms 2CH 4-8 Ohms 3CH 4-8 Ohms < 16 > WOOFER 4-8ohms 4CH 4-8 Ohms - Pyle HTG237 | Instruction Manual - Page 21
TROUBLE SHOOTING GUIDE SYMPTOMS NO SOUND AMP NOT SWITCHING ON NO SOUND IN ONE CHANNEL AMP TURNING OFF MEDIUM/ HIGH VOLUME CHECK POINTS Is the power LED illuminated? - Pyle HTG237 | Instruction Manual - Page 22
SPECIFICATIONS < 18 > MAXIMUM POWER OUTPUT POWER OUTPUT RMS @4Oh POWER OUTPUT RMS @2Oh POWER OUTPUT RMS @1Oh BRIDGED POWER MAX @4Oh THD FREQUENCY RESPONSE -3.0dB HPF LPF BASS BOOST(50Hz) ADJUSTABLE SENSITIVITY RANG INPUT IMPEDANCE(LOW LEVEL) FUSE DIMENSION(D x W x H inch HTG157 HTG237 HTG257 - Pyle HTG237 | Instruction Manual - Page 23
WARNINGS Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care when to work near the gas tanks, lines, or hydraulic lines, and electrical wiring. Don't use power amplifier unmounted. Attach this system securely to the automobile to prevent damage,