Pyle PLMRC400X4 Instruction Manual
Pyle PLMRC400X4 Manual
 |
View all Pyle PLMRC400X4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PLMRC400X4 manual content summary:
- Pyle PLMRC400X4 | Instruction Manual - Page 1
PLMRC400X4 4-Channel Weather-Resistant Audio Amplifier System Class D Compact Designed Suit for Car, ATV, UTV, 4X4, Jeep, Motorcycle and Marine, and any other Weather Resistant Application - Pyle PLMRC400X4 | Instruction Manual - Page 2
and it's features. Before installing the power ampli er please read this instruction manual carefully. The instructions for mounting and connecting the set have to be followed precisely. If necessary, a service center should be consulted. All connections for DC power, signal input and speaker - Pyle PLMRC400X4 | Instruction Manual - Page 3
PRECAUTIONS • This unit is designed for negative ground 12-14.50 VoIts (DC) operation only • Use speakers with an impedance of 2 or 4 Ohms (4 to 8 Ohm when used as bridged ampli er) • Avoid installing the unit where: • It would be subject to high temperatures, such as from direct sunlight or hot air - Pyle PLMRC400X4 | Instruction Manual - Page 4
WIRING INSTRUCTIONS POWER CONNECTION The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and - Pyle PLMRC400X4 | Instruction Manual - Page 5
INPUT WIRING DIAGRAM SPEAKER CONNECTIONS www.PyleUSA.com 5 - Pyle PLMRC400X4 | Instruction Manual - Page 6
BRIDGED MODE POWER CONNECTION LEADS NOTES ON THE POWER SUPPLY • Connect the + 12V power input lead only after all other leads have been connected. • Be sure to connect the ground wire of the unit securely to a metal part of the car. • A lose connection may cause amalfunction of the ampli er. 6 www. - Pyle PLMRC400X4 | Instruction Manual - Page 7
4 Ohm speakers in bridge mode and the overload protection is triggered out, turn the gain control to "Min" direction, until the operation is free of trouble. www.PyleUSA.com 7 - Pyle PLMRC400X4 | Instruction Manual - Page 8
X-OVER FREQUENCY CONTROL A. When the crossover control is in the Low-Pass position, this control becomes active allowing you to select your crossover point. B. When the crossover control is in the High-Pass position, this control becomes active allowing you to select your crossover point. CROSS OVER - Pyle PLMRC400X4 | Instruction Manual - Page 9
and OFF. A cable diameter of 0.5 mm' is su cient. TROUBLESHOOTING No Function The connection cable is not connected correctly (=terminaI + I2V/ turn the gain control to "min" until the operation is free of trouble. Poor Sound Quality (Distortions) The speakers are overloaded, therefore turn down - Pyle PLMRC400X4 | Instruction Manual - Page 10
cables are less prone. There is often interference caused by the generator (piping), ignition (cracking) or other car electronic parts. Most of these problems can be eliminated by correct and careful cabling. In doing so, here are the following guidelines: • Use only a screened audio cable for the - Pyle PLMRC400X4 | Instruction Manual - Page 11
Features: • 4-channel Audio Amp System • Weather Resistant Class D Compact Ampli er • IPX4 E ect • Integrated Power Wiring Harness • Perfect for Custom Installations & Applications • Ability to Connect & Stream Audio from External Devices • Speaker Wiring Connectivity • Soft Turn On /O • Overload & - Pyle PLMRC400X4 | Instruction Manual - Page 12
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: [email protected]
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
4-Channel Weather-Resistant Audio Amplifier System
PLMRC400X4
Class D Compact Designed Suit for Car, ATV,
UTV, 4X4, Jeep, Motorcycle and Marine,
and any other Weather Resistant Application