Pyle PLMRC500X1 Instruction Manual
Pyle PLMRC500X1 Manual
 |
View all Pyle PLMRC500X1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PLMRC500X1 manual content summary:
- Pyle PLMRC500X1 | Instruction Manual - Page 1
PLMRC500X1 Mono-Block Weather Resistant Audio Amplifier System Class D Compact Designed Suit for Car, ATV, UTV, 4X4, Jeep, Motorcycle and Marine, and any other Weather Resistant Application - Pyle PLMRC500X1 | Instruction Manual - Page 2
and it's features. Before installing the power ampli er please read this instruction manual carefully. The instructions for mounting and connecting the set have to be followed precisely. If necessary, a service center should be consulted. All connections for DC power, signal input and speaker - Pyle PLMRC500X1 | Instruction Manual - Page 3
PRECAUTIONS • This unit is designed for negative ground 12-14.50 VoIts (DC) operation only • Use speakers with an impedance of 1 to 4 Ohms (2 to 8 Ohm when used as bridged two ampli er) • Avoid installing the unit where: • It would be subject to high temperatures, such as from direct sunlight or hot - Pyle PLMRC500X1 | Instruction Manual - Page 4
WIRING INSTRUCTIONS POWER CONNECTION The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and - Pyle PLMRC500X1 | Instruction Manual - Page 5
INPUT WIRING DIAGRAM SPEAKER CONNECTIONS www.PyleUSA.com 5 - Pyle PLMRC500X1 | Instruction Manual - Page 6
POWER CONNECTION LEADS NOTES ON THE POWER SUPPLY • Connect the + 12V power input lead only after all other leads have been connected. • Be sure to connect the ground wire of the unit securely to a metal part of the car. • A lose connection may cause amalfunction of the ampli er. • REM: The unit is - Pyle PLMRC500X1 | Instruction Manual - Page 7
OPERATION After the ampli er has been installed and all connections have been made carefully and securely, turn the radio ON so that the ampli er is switched on automatically. After a short power-on period, the ampli er reaches its full performance. Now turn up the volume slowly using the volume - Pyle PLMRC500X1 | Instruction Manual - Page 8
BASS BOOST CONTROLS This ampli er has Bass controls for making good sound combination. FUSE The ampli er is equipped with a plug-in auto fuse protecting the set against fault conditions. Do not use a fuse with a higher value and never bridge the fuse over, as this may lead to irreparability damage - Pyle PLMRC500X1 | Instruction Manual - Page 9
TROUBLESHOOTING No Function The connection cable is not connected correctly (=terminaI the set is overloaded, then turn the gain control to "min" until the operation is free of trouble. Poor Sound Quality (Distortions) The speakers are overloaded, therefore turn down the volume level and check the - Pyle PLMRC500X1 | Instruction Manual - Page 10
cables are less prone. There is often interference caused by the generator (piping), ignition (cracking) or other car electronic parts. Most of these problems can be eliminated by correct and careful cabling. In doing so, here are the following guidelines: • Use only a screened audio cable for the - Pyle PLMRC500X1 | Instruction Manual - Page 11
Features: • Mono Block Audio Amp System • Weather Resistant Class D Compact Ampli er • IPX4 E ect • Integrated Power Wiring Harness • Perfect for Custom Installations & Applications • Ability to Connect & Stream Audio from External Devices • Speaker Wiring Connectivity • Soft Turn On/O • Overload & - Pyle PLMRC500X1 | Instruction Manual - Page 12
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: [email protected]
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
Mono-Block Weather Resistant Audio Amplifier System
PLMRC500X1
Class D Compact Designed Suit for Car, ATV,
UTV, 4X4, Jeep, Motorcycle and Marine,
and any other Weather Resistant Application