Pyle PRJLEDLP205 Instruction Manual

Pyle PRJLEDLP205 Manual

Get Pyle PRJLEDLP205 PDF manuals and user guides View all Pyle PRJLEDLP205 manuals
Add to My Manuals
Save this manual to your list of manuals

Pyle PRJLEDLP205 manual content summary:

  • Pyle PRJLEDLP205 | Instruction Manual - Page 1
    DIGITAL PROJECTOR INSTRUCTION MANUAL Model: PRJLEDLP205
  • Pyle PRJLEDLP205 | Instruction Manual - Page 2
    installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • Pyle PRJLEDLP205 | Instruction Manual - Page 3
    . 2. Notes and warnings All notes and warnings in the operating instructions should be adhered to. 3. Cleaning Unplug the projector from the wall power supply. 7. Servicing Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel. 8. Replacement parts
  • Pyle PRJLEDLP205 | Instruction Manual - Page 4
    Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your
  • Pyle PRJLEDLP205 | Instruction Manual - Page 5
    the Lens ...29 Cleaning the Projector Housing ...29 Replacing the Lamp ...30 Specifications 32 Dimensions ...33 Appendix 34 LED Indicator Messages...35 Compatibility Modes...35 Troubleshooting ...36 RS-232 Command and Configuration 37 IR Control Table...38 EN-1
  • Pyle PRJLEDLP205 | Instruction Manual - Page 6
    0.5 W power consumption in standby mode • SmartEco?mode lowers the po wer consumption to increase the lamp life hours Note • The information in this manual is subject to change without notices. • The reproduction, transfer or copy of all or any part of this document is not permitted without express
  • Pyle PRJLEDLP205 | Instruction Manual - Page 7
    Projector Overview Front View 8 76 5 12 3 4 1. Front IR remote control sensor 3. Projection lens 5. Ventilation holes 7. Control panel 2. Elevator foot 4. Focus ring 6. Zoom ring 8. Lamp cover EN-6
  • Pyle PRJLEDLP205 | Instruction Manual - Page 8
    AC power socket Bottom View 1 2. Connection ports 1 2 1. Security bar 2. Ceiling mount holes Note • This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. • Contact your dealer for information to mount the projector on a ceiling. EN-7
  • Pyle PRJLEDLP205 | Instruction Manual - Page 9
    Using the Product Control Panel 2 3 4 9 POW TEMP LAMP 1 1. 电源 (Power) Turn the projector on or off 2. 电源 (Pow ) (Power LED indicator) Refer to "LED Indicator Messages". 3. 温度 (Temp) (Temp LED indicator) Refer to "LED Indicator Messages". 4. 灯泡 (Lamp) (Lamp LED indicator) Refer to "LED
  • Pyle PRJLEDLP205 | Instruction Manual - Page 10
    Connection Ports 12 3 4 1. RS-232 When operating the projector via a computer, connect this to the controlling computer's RS-232C port. 2. VIDEO Connect composite video output from video equipment to this jack. 3. TYPE B USB This connector is for firmware update. 4. COMPUTER Connect image input
  • Pyle PRJLEDLP205 | Instruction Manual - Page 11
    the projector on or off. 2. VGA1 Display COMPUTER IN 1 signal. 3. Source Display the source selection bar. 4. Keystone/Arrow keys ( /Up, /Down) Manually correct distorted images resulting from an angled projection. 5. Left When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys
  • Pyle PRJLEDLP205 | Instruction Manual - Page 12
    10. Mouse No function. 11. Lock No function. 12. Pattern No function. 13. Blank Hide the screen picture. 14. Eco Decreases the power consumption of the lamp by up to 70%. Note: It takes some time to initiate this function. Make sure the projector has been turned on for more than 4 minutes. 15. Auto
  • Pyle PRJLEDLP205 | Instruction Manual - Page 13
    28. Aspect Select the display aspect ratio. 29. Timer Activate P-Timer OSD menu. Using the remote mouse control Connect the projector to your PC or notebook with a USB cable prior to using the paging the paging function. You can operate your display software program (on a connected PC) which
  • Pyle PRJLEDLP205 | Instruction Manual - Page 14
    the battery cover into position. Caution • Risk of explosion if battery is replaced by an incorrect type. • Dispose of used batteries according to the instructions. • Make sure the plus and minus terminals are correctly aligned when loading a battery. Note • Keep the batteries out of the reach of
  • Pyle PRJLEDLP205 | Instruction Manual - Page 15
    Remote Control Operation Point the remote control at the infrared remote sensor and press a button. • Operating the projector from the front 15 15 5m 8m 7m Note • The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote
  • Pyle PRJLEDLP205 | Instruction Manual - Page 16
    Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. 12 3 4 1. VGA cable 3. VGA (D-Sub) to HDTV (RCA) cable 2. USB cable 4.
  • Pyle PRJLEDLP205 | Instruction Manual - Page 17
    Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a
  • Pyle PRJLEDLP205 | Instruction Manual - Page 18
    Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused output jacks available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to
  • Pyle PRJLEDLP205 | Instruction Manual - Page 19
    Operation Powering On/Off the Projector Powering On the Projector: 1. Complete the AC power cord and peripheral signal cable(s) connections. 2. Press to turn on the projector. The projector takes a minute or so to warm up. 3. Turn on your source (computer, notebook, DVD, etc.). The projector
  • Pyle PRJLEDLP205 | Instruction Manual - Page 20
    Adjusting the Projector Height Elevator foot The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image, turn the elevator foot to fine-tune the height. Adjusting the Projector Zoom and Focus Zoom ring Focus ring 1. Focus the image by rotating the focus
  • Pyle PRJLEDLP205 | Instruction Manual - Page 21
    Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance The screen aspect ratio is 4:3 and the projected picture is 4:3 Screen size
  • Pyle PRJLEDLP205 | Instruction Manual - Page 22
    Menu Operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. How to operate 1. Press the Menu button to open the OSD menu. 2. When OSD is displayed, use / to select any feature in the main menu. 3. After selecting
  • Pyle PRJLEDLP205 | Instruction Manual - Page 23
    Picture Mode Dynamic /Presentation /sRGB/Cinema / User 1 /User 2 Reference Mode Dynamic /Presentation /sRGB/Cinema Brightness Contrast Sharpness Tint Color Temperature Cool/Normal /Warm 2. PICTURE Color Temperature Fine Tuning R Gain/G Gain/B Gain/R Offset/G Offset/B Offset Primary Color
  • Pyle PRJLEDLP205 | Instruction Manual - Page 24
    Presentation Timer Timer Period Timer Display Timer Position Timer Counting Direction 1~240 minutes Always /3 min/2 min/1 min/ Never Top-Left /Bottom-Left/TopRight/Bottom-Right Count Down /Count Up Language 4. SYSTEM SETUP: Basic Projector Installation Front Table /Rear Table/Rear Ceiling/
  • Pyle PRJLEDLP205 | Instruction Manual - Page 25
    5. SYSTEM SETUP: Advanced High Altitude Mode Lamp Settings Security Settings Baud Rate Test Pattern On/Off Yes/ No Lamp Mode Normal/Economic/ SmartEco Lamp Spa Mode On /Off Reset lamp timer Reset /Cancel Equivalent lamp hour Change Password Change Security Power On Lock 2400/4800/9600/
  • Pyle PRJLEDLP205 | Instruction Manual - Page 26
    of the screen with a 16:10 aspect ratio. Auto Keystone Automatically correct distorted images resulting from an angled projection. Keystone Manually correct distorted images resulting from an angled projection. Press Keystone / on the projector or remote control to display the Keystone correction
  • Pyle PRJLEDLP205 | Instruction Manual - Page 27
    projector detects the signal for 3D Sync information and once detected, it projects images in 3D format automatically. In other cases, you may need to manually select a 3D Sync format for the projector to project 3D images correctly. Note • 3D Format will be available when 3D Sync is "On". • The
  • Pyle PRJLEDLP205 | Instruction Manual - Page 28
    PC graphic and drawing applications such as AutoCAD. • Cinema mode : Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment. Brightness Brighten or darken the image. Contrast Set the
  • Pyle PRJLEDLP205 | Instruction Manual - Page 29
    • Menu Position: Choose the menu location on the display screen. • Menu Display Time: Duration of OSD menu display countly starts (at idle state by second). Opration Setting Direct Power On • On: The projector will turn on in 3 seconds. • Off: The projector will turn on following normal power on
  • Pyle PRJLEDLP205 | Instruction Manual - Page 30
    as dust, dirt or spots will project on the screen and diminish image quality. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first. Warning • Never open any of the covers on
  • Pyle PRJLEDLP205 | Instruction Manual - Page 31
    to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. Note • The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald
  • Pyle PRJLEDLP205 | Instruction Manual - Page 32
    1. Turn off the projector. 2. If the projector is installed in a ceiling mount, remove it 3. Unplug the power cord. 4. Loosen the screw in the side of the lamp cover and remove the cover. 5. Remove the screws from the lamp module, raise the handle, and lift out the module. 6. Insert the new lamp
  • Pyle PRJLEDLP205 | Instruction Manual - Page 33
    - 300" 190W D-Sub 15-pin x 1, Video x 1, Output terminal NA Control terminal Speaker Video compatibility RS-232 x 1, USB B type x1 (supports firmware upgrade) NA NTSC, NTSC 4.43 PAL, PAL-N, PAL M SECAM, Composite video Scanning frequency Horizontal frequency Vertical frequency Environment Power
  • Pyle PRJLEDLP205 | Instruction Manual - Page 34
    Dimensions 285 mm (W) x 208 mm (D) x 116 mm (H) 208 POW TEMP LAMP 285 116 Ceiling mount installation Ceiling mount screws: M4 x 8 （Max. L = 8mm） Unit: mm 77 198 9 EN-33
  • Pyle PRJLEDLP205 | Instruction Manual - Page 35
    Appendix LED Indicator Messages 电源 LED Solid Orange 1Hz Green Blinking Solid Green 1Hz Orange Blinking Off Off Off Off Off Off 5Hz Orange Blinking Off Off Off 温度 LED (Red) 灯泡 LED (Red) Power Events Off Off Off Off Off Off Off Off Lamp Error Message Off Solid Off Blinking 1 Hz
  • Pyle PRJLEDLP205 | Instruction Manual - Page 36
    Compatibility Modes Computer: Resolution 640 x 350 640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 768 1280 x 800 1280 x 960 1280 x 1024 1400 x 1050 1600 x 1200 Video: Compatibility 480i 480p 576i 576p 720p 720p 1080i 1080i 1080p 1080p Resolution 720 x 480 720 x 480 720 x 576 720 x 576
  • Pyle PRJLEDLP205 | Instruction Manual - Page 37
    Troubleshooting Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well. Start-up problems on. Refer to the computer manual. If the image is out
  • Pyle PRJLEDLP205 | Instruction Manual - Page 38
    RS-232 Command and Configuration D-Sub 9 pin 1 1 CD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI Baud Rate Data Length Parity Check Stop Bit Flow Control Wire List C1 COLOR 1 Black 2 Brown 3 Red 4 Orange 5 Yellow 6 Green 7 Blue 8 Purple 9 White SHELL DW C2 1 3 2 6 5 4 8 7
  • Pyle PRJLEDLP205 | Instruction Manual - Page 39
    IR Control Table Customer code: 0X2626 Format : NEC 17 08 41 45 52 40 10 0b 0e 15 0f 0c 30 56 28 36 37 06 05 31 18 82 8E 03 83 55 07 14 2B 27 13 EN-38
  • Pyle PRJLEDLP205 | Instruction Manual - Page 40
    Key Power Auto Sync VGA1 VGA2 Video Source Color Mode Enter Up / Keystne+ Down / KeystoneLeft Right Menu My Button(Function) Exit Mouse Mouse left Mouse right Mouse Page Up Mouse Page Down Lock(Key pad) Pattern Eco Magnify + Freeze Blank Timer (Presentation) Volume+ VolumeMute Aspect Format NEC NEC
  • Pyle PRJLEDLP205 | Instruction Manual - Page 41
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
DIGITAL PROJECTOR
INSTRUCTION MANUAL
Model:
PRJLEDLP205