Pyle PTA3000 PTA3000 Manual 1
Pyle PTA3000 Manual
 |
View all Pyle PTA3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle PTA3000 manual content summary:
- Pyle PTA3000 | PTA3000 Manual 1 - Page 1
PROFESSIONAL POWER AMPLIFIER PTA3000 OPERATING GUIDE - Pyle PTA3000 | PTA3000 Manual 1 - Page 2
of important operating and maintenance (servicing) instructions in the literature accompanying the read the operating guide for further warnings. IMPORTANT SAFETY INSTRUCTIONS. When using ventilation openings. Install in accordance with manufacture's instructions. 8. Do not install near any heat - Pyle PTA3000 | PTA3000 Manual 1 - Page 3
of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has Write for our free booklet "Shock Hazard and Grounding". Connect only to a power supply of the type marked on be mounted in an equipment rack, rear support should be provided. 17. Exposure to - Pyle PTA3000 | PTA3000 Manual 1 - Page 4
on the desired channel. Select the proper mode configuration (STEREO or BRIDGE). Connect speakers to the proper OUTPUT connectors, reviewing carefully the impedance and phase considerations. With the POWER switch OFF, connect the IEC cord (7) to the amplifier and then to a suitable electrical outlet - Pyle PTA3000 | PTA3000 Manual 1 - Page 5
a good idea to power up any new installing at this setting to protect the system loudspeakers signal level exceeds 1 V RMS. (4) OVERLOAD LEDS (CLIP) amplifier is detected some problem inside such as overheat or circuit problem so that can protect connected to the amplifier and protects loudspeakers. 4 - Pyle PTA3000 | PTA3000 Manual 1 - Page 6
plug with ground pin. It should be connected to an independent circuit capable of continuously supporting at least 15 amps. This is particularly the power capability of this amplifiers. Always use a qualified electrician to install any new electrical equipment. To prevent the risk of shock or fire - Pyle PTA3000 | PTA3000 Manual 1 - Page 7
amped systems. Amplifier BRIDGE mode theory will be covered later in this manual. (11) GROUND LIFT SWITCH Avoid background noise and hum. Turn be accomplished using a male XLR, a 3-conductor phone jack, or bare wires connected to the barrier strip. As an alternative, the 1/4" input can also be - Pyle PTA3000 | PTA3000 Manual 1 - Page 8
the same rack. This function allows one balanced mixer feed to be connected to the amp via the desired balanced input connector (XLR, 1/4", signle-conductor shielded cables. INDUSTRIAL AND COMMERCIAL INSTALLATIONS For commercial and other installation where sustained high-power operation is required, - Pyle PTA3000 | PTA3000 Manual 1 - Page 9
the amplifiers. As a general rule, the cooler electronic equipment is operated, the longer its useful service life. In most low to medium-power applications, the amplifier can be mounted in any configuration. a cabinet, a power amplifier will have severe cooling problems, even at low power levels. 8 - Pyle PTA3000 | PTA3000 Manual 1 - Page 10
AMPLIFIER CONFIGURATIONS - Pyle PTA3000 | PTA3000 Manual 1 - Page 11
10 - Pyle PTA3000 | PTA3000 Manual 1 - Page 12
SPECIFICATIONS RATED OUTPUT POWER: Stereo mode (EIA both channels driven) 4 Ohms EIA, 1 kHz, 1% THD 8 Ohms EIA, 1 kHz, 1% THD Bridge mode, mono 8 Ohms EIA, 1 kHz, 1% THD HUM & NOISE: Stereo mode, below rated output power, 4 ohms 300W RMS/chan 400W RMS/chan 500W RMS/chan 600W RMS/chan 700W RMS/chan - Pyle PTA3000 | PTA3000 Manual 1 - Page 13
PyleAudio.com 718.535.1800 718.236.2400 (fax) 1600 63rd Street, Brooklyn NY 11204
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
PROFESSIONAL POWER AMPLIFIER
OPERATING GUIDE
PTA3000