Pyle PVCD15 Instruction Manual

210x285mm

PVCD15

High-Power In-Wall Stereo Volume control

Your PYLE

High-Power

In-wall

stereo

volume

control lets you

adjust

the

volume

on a

pair

speaker

that

are located in a room

separate

from

the

amplifier,so

you can

control

the

sound on

the

spot.

Caution:

thIs

volume

contraIls

limIted

to

a

maxImum

of

120

watts

RMS

per

channel.

Connections

Notes:

•

This

volume

control

can be used with up to

14-gauge

wire.

•

Measure the

distance

from the

speaker

to

the

amplifier.

For

distances

of

50

feet

or

less, use

18-gauge

speaker

wire

or

ordinary

lamp

cord.

For

distances

greater

than

50 feet, use

heavier

16-gauge

wire.

Caution:

Letting

strav

wire

ends

touch

an

adjacent

terminal.

the

mounting

brackets

or

screws.

or

the

metal

sides

of

the

electrical

box

could

cause

a

short

cIrcuit

of

damage

a

speaker.

Fi

gure

#1

-

-

Amplifier/Receiver

+

+

I

I

(

')

~U

E'\

E

'='I

EIUV

I

I

~t

l

J~

Speaker B

Speaker A

1.

Strip

off

Y,

inch(12.7mm)

of

insulation

from each end

of

the

amplifier/receiver

and

speaker

wires.

Caution:

Be

sure

to

follow

the

correct

polarltv(+

to

+

and-

to

.)

when

making

connections.

Improper

connections

might

cause

poor

sound

reproduction.

2.

Insert

the

amplifier/receive's

+ and -

speakers

output

wires

into

the

vomume

control's

INPUT

+(positive)

and

-(negative)

terminals,

then

tighten

the

screws.

3.

Insert

the

speaker's

+ and - wire ends

into

volume

control's

OUTPUT

+ and - terminals,

then

tighten

the

screws

.

Mounting the Volume Control

The

volume

control

is

designed

to be mounted in a

standard

electrical

wall box.

Select

a

location

that

is:

•

Within

reach

of

the

speaker

wires

•

Easy to reach

for

using

the

volume

control

Caution:

You

must

mount

the

volume

control

In

a

standard

electrical

box.

Do

not

mount

It

dlrectlv

on

a

wall.

Important:

•

Over-Tightening

the

screws

might

damage

the

wall plate.

• Some

electrical

wall

boxes

are a

nonstandard

size.Be

sure

that

you measure the wall box

before

you

mount

the

volume

control.

Once

the

control

has been wired,

it

is ready to be mounted

into

the

wall.

Referring

to Figure #2,

place

the

components

of

the

volume

control

into the wall in

the

order

illustrated.

Use the

enclosed

screws

to hold

the

components

in place.

NOTE:

The

rotary

switch is

shipped

with

the

control

turned as

far

counterclockwise

as

it

will

turn off.

If

you changed this,

return

it

to

the full

counterclockwise

position

before

starting

installation.

Figure #2

ELECTRICAL

BOX

SPEAKER W I

RE

VOLUME

CONTROL

INSTALLA

TI

ON

SCREWS

(supplied)

DECORATOR COVER PLATE

Isuppli

e

d)

COVER PLATE

SCREWS

(supplied)

Operation

Set

the

amplifier/receive's

volume

control to minimum

by

turning

it

fully

counterclockwise.

Then

turn

on

the

amplifier/receiver

and

set

its

volume

control

slightly

above

the

normal

listening

level.

To

increase

or

decrease

the

remote

speaker's

volume, turn

the

wall-mount

volume

control

clockwise

or

counterclockwise.

Pyle PVCD15 Instruction Manual

Pyle PVCD15 Manual

Pyle PVCD15 manual content summary: