RCA ANT702F User Guide

RCA ANT702F Manual

Get RCA ANT702F PDF manuals and user guides View all RCA ANT702F manuals
Add to My Manuals
Save this manual to your list of manuals

RCA ANT702F manual content summary:

  • RCA ANT702F | User Guide - Page 1
    ANT702F Digital Amplified Indoor/Outdoor Antenna User's Guide frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly
  • RCA ANT702F | User Guide - Page 2
    attach foreign objects to the antenna. NOTES: Do not install the antenna on any metal surface, including aluminum siding. Mounting on a metal surface will seriously degrade reception quality. In most cases, the antenna provides the best performance when mounted outdoors in a high location (such as
  • RCA ANT702F | User Guide - Page 3
    to concrete, brick, or drywall... You'll need to use the anchors included in this package. Here's how to install them: • Place the antenna base against the concrete where you want to mount the antenna. Make sure it's level. • Mark the surface through the holes in the base where you're going to
  • RCA ANT702F | User Guide - Page 4
    side of the well. Tighten the bolt to attach the arm to the base. 3. Attach the antenna to the arm. Find the other bolt included in this package. First, set the bolt in the antenna's mounting well. Then position the arm over the other side of the well. Tighten the bolt to
  • RCA ANT702F | User Guide - Page 5
    . Cover the connector with the cable's attached weather boot. To adjust the antenna's position: 1. Loosen the bolt on either end of the arm. 2. Move the arm or antenna to the desired position. 3. Re-tighten the bolt so that the antenna and arm stay firmly in position. Mounting to a Mast 1. If you're
  • RCA ANT702F | User Guide - Page 6
    clamp assembly over the mast, positioning the mast between the clamp and the antenna base. Position the antenna base as high as possible on the mast. Orient the base in the direction you want. Then tighten the clamps and washer nuts securely onto the mast. Note: If you used the provided coaxial
  • RCA ANT702F | User Guide - Page 7
    the well. Tighten the bolt to attach the arm to the base as shown here. Important: These diagrams show the cable that came with this antenna.This cable was designed to fit under the U-bolt. If you are using a different cable, DO NOT pass it under the U-bolt as shown here. Instead
  • RCA ANT702F | User Guide - Page 8
    horizontally, simply rotate the arm clockwise 90O. Try different positions for best performance. 90° Important: These diagrams show the cable that came with this antenna.This cable was designed to fit under the U-bolt. If you are using a different cable, DO NOT pass it under the U-bolt as shown here
  • RCA ANT702F | User Guide - Page 9
    PUT THE SIGNAL SPLITTER BETWEEN THE AMPLIFIER INSERT AND THE ANTENNA. 3. After all other connections are made, connect the power adapter into the amplifier insert. Plug it into a standard AC outlet. The amplifier insert should always be located indoors. TO TV HI LOW TO ANT +12 VDC 4. Set the switch
  • RCA ANT702F | User Guide - Page 10
    Water Damage Prevention: At the point where your coaxial cable lead enters the house, you should allow for some slack in the coaxial cable as a "drip loop." This will prevent moisture from running down the coaxial cable and entering the house. Run the coaxial cable approximately six inches below the
  • RCA ANT702F | User Guide - Page 11
    transferable and does not cover product purchased, serviced or used outside the United States or does not apply to costs incurred for installation, removal or reinstallation of the product, THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. ANT702F NA IB 01 11
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
1
ENGLISH
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the
FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the radio or television off and on, the user
is encouraged to try to correct interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on another circuit.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
Avis d’Industrie Canada
CAN ICES-3 (B)/NMB-3 (B)
Important:
This power adapter should be plugged in so that it stays vertical or lays flat.
ANT702F
Digital Amplified Indoor/Outdoor Antenna
User’s Guide
Getting Started
Remove the antenna and the hardware bag from package. Make sure the
following parts are in the package:
•
Antenna
•
Amplifier Insert
•
Power Adapter
•
Mounting Base
•
Mounting Arm
•
Hardware bag:
(2) U-Bolts
(2) Clamps
(4) Plastic Anchors
(4) Wood screws
(4) Washer Nuts
(1) Coaxial cable
(2) Bolts
BEFORE YOU START!!!
Please read the IMPORTANT SAFETY INFORMATION sheet included in
this package.
ENGLISH