RCA HD50LPW165 User Guide & Warranty - Page 25

Plug in the TV, Put Batteries in the Remote, Turn on the TV, Use the Remote Control to Complete, - flashes 5

Get RCA HD50LPW165 - 50inch Rear Projection TV PDF manuals and user guides View all RCA HD50LPW165 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Connections & Setup Plug in the TV Plug the flat end of the power cable into the power jack on the back of the TV. Then plug the other end of the power cord into an appropriate wall outlet. Be sure to insert the plug completely. Do not plug into an outlet controlled by a light switch. Note: When you first plug your TV into an outlet, the Power indicator on the front panel will light and blink for approximately 30 seconds and then go off during the initialization of the TV. The TV can only be turned on after the Power indicator goes off. This happens every time the TV is unplugged and plugged back in. Put Batteries in the Remote • Remove the battery compartment cover from the back of the remote by pushing down on the tab and lifting cover. • Insert 2 fresh "AA" batteries. Make sure the polarities (+ and -) are aligned correctly with the polarities inside the remote. • Replace the cover. Tip When remote batteries are low, the component button(s) corresponding to the mode you're in flashes when you press a button. Also, a message might appear on the TV screen and disappear within a few seconds. Press CLEAR and replace the batteries to remove the message. learning ON-OFF TV DVD VCR SAT/CAB AUX AUDIO PIP SWAP CH. CTRL FREEZE CC PRESETS FAV CC LIGHT FORMAT CLEAR C INFO i MENU M SOUND SKIP TV button MENU button OK button Arrow buttons Turn on the TV Press TV on the remote, or press the Power button on the TV's front panel. Note: Pressing the TV button turns on the TV and puts the remote into TV mode. "TV mode" means that the buttons on the remote control operate the TV's functions. Use the Remote Control to Complete the Assisted Setup The technical term is "Navigation" - how you move through the on-screen menus. The method is the same throughout the menu screens: highlight your choice and select it. To highlight a menu item, put the remote into TV mode by pressing the TV button then MENU. Press the arrow buttons on the remote to highlight one of the items listed in the menu. Use the up or down arrow button to move up or down. Use the right or left arrow button to move right or left. To select the item that you've highlighted, press OK. Note: Highlighted means that the menu item stands out from other menu items on the list (appears darker, brighter, or a different color). Tip To access the setup menus, press MENU and choose Assisted Setup. Chapter 1 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Connections & Setup
Chapter 1
23
Tip
To access the setup menus, press MENU and
choose Assisted Setup.
Plug in the TV
Plug the flat end of the power cable into the power jack on the back of the TV. Then plug the
other end of the power cord into an appropriate wall outlet. Be sure to insert the plug
completely. Do not plug into an outlet controlled by a light switch.
Note:
When you first plug your TV into an outlet, the Power indicator on the front panel
will light and blink for approximately 30 seconds and then go off during the initialization
of the TV. The TV can only be turned on after the Power indicator goes off. This happens
every time
the TV is unplugged and plugged back in.
Tip
When remote batteries are low, the component
button(s) corresponding to the mode you’re in
flashes when you press a button. Also, a message
might appear on the TV screen and disappear
within a few seconds. Press CLEAR and replace the
batteries to remove the message.
Put Batteries in the Remote
•
Remove the battery compartment cover from the back of the remote
by pushing down on the tab and lifting cover.
•
Insert 2 fresh “AA” batteries. Make sure the polarities (+ and -) are
aligned correctly with the polarities inside the remote.
•
Replace the cover.
Turn on the TV
Press TV on the remote, or press the Power button on the TV’s front
panel.
Note:
Pressing the TV button turns on the TV and puts the remote
into TV mode. “TV mode” means that the buttons on the remote
control operate the TV’s functions.
Use the Remote Control to Complete
the Assisted Setup
The technical term is “Navigation” – how you move through the on-screen
menus. The method is the same throughout the menu screens: highlight
your choice and select it.
To highlight a menu item, put the remote into TV mode by pressing the
TV button then MENU. Press the arrow buttons on the remote to highlight
one of the items listed in the menu. Use the up or down arrow button to
move up or down. Use the right or left arrow button to move right or left.
To select the item that you’ve highlighted, press OK.
Note:
Highlighted means that the menu item stands out from
other menu items on the list (appears darker, brighter, or a
different color).
ON-OFF
TV
DVD
VCR
AUX
AUDIO
SAT
CH. CTRL
SKIP
PIP
SWAP
PRESETS
FAV
CC
SOUND
CLEAR
FORMAT
INFO
MENU
FREEZE
i
learning
LIGHT
CAB
/
CC
CC
C
M
TV
button
Arrow
buttons
OK button
MENU button