RCA MST46BKR Owner/User Manual
RCA MST46BKR Manual
 |
View all RCA MST46BKR manuals
Add to My Manuals
Save this manual to your list of manuals |
RCA MST46BKR manual content summary:
- RCA MST46BKR | Owner/User Manual - Page 1
26" to 46" 99lb (45kg) 400 mm x 400 mm (15.7" x 15.7") max 15° down 1.4" (3.5cm) Mount Arm (x2) Instruction Manual (x1) Hardware Kit (x1) Template (x1) Warnings 1. Read these instructions before you begin. If you are unsure of any part of the process, contact a professional contractor or installer - RCA MST46BKR | Owner/User Manual - Page 2
wood studs no less than 16" apart. The studs must be capable of supporting the combined weight of the mount and display. 1. Use a high quality stud 3. Drill four 3 mm (1/8") pilot holes in the wall using the template as a guide. Drill two holes per stud (see Fig. 2). 4. Remove the template from the - RCA MST46BKR | Owner/User Manual - Page 3
! For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and the display. The manufacturer . 2. Drill four 8 mm (5/16") holes in the wall using the template as a guide. Remove any excess dust from the holes. (see Fig. 4). 3. Remove the template from - RCA MST46BKR | Owner/User Manual - Page 4
3. Attach the mount arms to the back of your display using the screws identified in steps 1 and 2 (see Fig. 6): For displays with flat backs. For displays with curved or recessed backs. Fig.6 A. If you are using the M4 or M6 screws you will also need to use the M6 washers (J). M8 screws do not - RCA MST46BKR | Owner/User Manual - Page 5
English Operation and adjustment 1. To change the tilt angle of your display, hold the display firmly in place and loosen the tilt mechanisms using the long Allen key (L) from the hardware kit (see Fig. 9). Move your display to the desired position, and then re-tighten the tilt mechanisms. If your
-
1 -
2 -
3 -
4 -
5
 |
 |
1.
Read these instructions before you begin.
If
you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.
2.
The wall or mounting surface must be capable of
supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.
3.
Locate pipes, wires, or any other hazards in the wall
where you wish to install the mount before drilling.
4.
Safety gear and proper tools must be used. Failure
to do so can result in injury or damage.
5.
A minimum of two people are required for
installation. Do not attempt to install this mount
alone under any circumstances.
6.
Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.
Warnings
CAUTION:
This wall mount is intended for use only with the
maximum weight of 45 kg/99 lbs. Use with heavier
than the maximum weights indicated may result in
instability causing possible injury.
Specifications
Display Size:
26” to 46”
Maximum Load:
99lb (45kg)
Mounting Pattern:
400 mm x 400 mm (15.7” x 15.7”) max
Tilt Range:
15° down
Profile:
1.4” (3.5cm)
flat panel
solutions
Tilt Wall Mount for LCD, Plasma, and
LED Displays
Instruction Manual
MST46BKR
Fits TVs 26”- 46”
Maximum Load
Capacity – 99 lb (45 kg)
Continues on next page...
Pour des instructions
en français, se
reporter à la page 6.
Para obtener
instrucciones en
español, consulte la
página 11.
Box contents
Upper Wall Plate (x1)
Lower Wall Plate (x1)
Left Plastic Side (x1)
Right Plastic Side (x1)
Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Template (x1)