RCA RCR412SIR Owner/User Manual

Battery Saver

Your universal remote control saves battery power by

automatically turning off if any key is pressed for more than

60 seconds. This saves your battery life should your remote

get stuck in a place where the keys remain depressed, such as

between sofa cushions.

Universal Remote Control

Owner’s Manual

RCR412BR / RCR412SR / RCR412SIR

Manual del Propietario (parte posterior)

SAVE THIS MANUAL AND THE CODE LISTS!

Remote controls can sometimes lose their programming

when you change the batteries. Make sure you keep the

manual and code lists in a safe place so that you can

reprogram the remote if you need to.

Tip:

This remote is already programmed to operate

most RCA-branded TVs, VCRs, DVD players and satellite

receivers. Just press the corresponding key—DVD for

Your universal remote requires two

AA

alkaline batteries

(batteries may or may not be included, depending on model).

To install the batteries:

1.

Remove the battery compartment

cover.

2.

Insert the batteries, matching the

batteries to the (+) and (–) marks

inside the battery compartment.

3.

Push the battery cover back into place.

Battery Precautions:

and National Regulations.

To use this universal remote with your home entertainment

system, ﬁrst you need to program it to control your devices.

There are four ways you can program the universal remote to

operate your devices:

Auto Code Search

goes automatically through all the

codes for the device you’re trying to control. It’s the easiest

method, but it can sometimes take longer than some of the

other programming methods.

Brand Code Search

searches through the codes for

select brands of devices. It’s not as easy as the auto code

search, but it can be faster.

Direct Code Entry

lets you enter a code from the

accompanying code list for your brand of device. It’s not as

easy as the other methods, but it’s potentially the fastest

method.

Manual Code Search

lets you manually go through

all the codes for the device you’re trying to control.

Testing the Code for Maximum Functionality

1.

Try a variety of the device’s functions with the remote. If

some device features don’t work, go to next step to try a

different code.

2.

Repeat the Auto Code Search Method from the beginning.

Instead, with the unit now off, continue to press the PLAY

key every 5 seconds until the unit turns back on.

3.

Once the unit turns back on, press the REVERSE key on the

remote every 2 seconds until your device turns off again.

4.

Test the key’s functionality again by attempting to control

a variety of the device’s functions. If the code that has

been stored controls the majority of the device’s functions,

programming is complete. If the code stored does not give

maximum functionality, try another code.

Auto Code Search

The Auto Code Search goes automatically through all the

the one that operates your device, you can stop the search and

store that code.

1.

Manually turn on the device you

want to control.

2.

you’re holding down the device key, use your other hand

to press and hold the remote’s

key at the same

time.

3.

comes on and stays on. Then

release both keys.

4.

Point the remote directly at the

front panel of the device you

want to control. Press PLAY on

the remote and wait 5 seconds.

The remote is testing a batch of

10 codes on your device.

Did your device turn off?

YES:

Go to step

5

.

NO:

Press PLAY again. The remote tests the next batch of

10 codes.

turns off.

5.

the REVERSE key on the remote

and wait at least 2 seconds.

The remote tries the last of the

previous ten codes.

Did your device turn on?

YES:

Press the STOP key. You’re

done! You’ve programmed this

device key.

NO:

Press REVERSE again. The remote tests the next

code in the batch.

Note:

If you accidentally press the REVERSE key after your

device turns on, press the FORWARD key. Then, wait two

seconds to see if your device turns off again.

NOTES

Throughout the programming of each key, be sure to keep

the remote pointed at the IR sensor of the device you are

currently programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

Functionality” section below for more information.

During the Auto Code Search, the remote ignores

blinks four times and turns off, and the last programmed

try a different search method.

Step 1: Install your batteries

Step 2: Program your remote

TIPS

:

Each device key is associated with a type of device—

a device key for a different type of device, see the

Changing

section.

Code Search, press the

key.

RCA RCR412SIR Owner/User Manual

RCA RCR412SIR Manual

RCA RCR412SIR manual content summary: