RCA RP5605 User Manual - RP5605

Stop the wake function:

Press

OFF

.

The wake

function will activate

again on the following

day at the same time.

Cancel the wake function

completely:

Press

WAKE MODE

repeatedly until no

indicator lights against

the wake source icons.

The set wake time will

not be erased and can be used

the next time when you switch on

wake function again.

Setting clock

1. Press

CLOCK SET

once. The

current clock time flashes on

the display.

2. Press

or

to set the clock

time. The time decrements or

increments will follow by a

faster rate when you press and

hold the buttons. AM or PM

indicator also lights beside the

time on the display.

3. When finished, wait for about

5 seconds or press

CLOCK SET

to exit clock setting mode.

has been damaged in any way,

such as power-supply cord or

plug is damaged, liquid has

been spilled or objects have

fallen into the apparatus, the

apparatus has been exposed

to rain or moisture, does not

operate normally, or has been

dropped.

•

ADDITIONAL SAFETY

INFORMATION

•

Apparatus shall not be exposed

to dripping or splashing and

no objects filled with liquids,

such as vases, shall be placed

on the apparatus.

•

Always leave sufficient space

around the product for

ventilation. Do not place

product in or on a bed, rug,

in a bookcase or cabinet that

may prevent air flow through

vent openings.

•

Do not place lighted candles,

cigarettes, cigars, etc. on the

product.

•

Connect power cord only to

AC power source as marked on

the product.

•

Care should be taken so that

objects do not fall into the

product.

fit into your outlet, consult an

electrician for replacement of

the obsolete outlet.

•

Protect the power cord

from being walked on or

pinched particularly at plugs,

convenience receptacles, and

the point where they exit from

the apparatus.

•

Only use attachments/

accessories specified by the

manufacturer.

•

Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to

avoid injury from tip-over.

•

Unplug this apparatus during

lightning storms or when

unused for long periods of

time.

•

Refer all servicing to qualified

service personnel. Servicing is

required when the apparatus

user

manual

manual de usuario

EN/E

It is important to read this instruction prior to using your new product for the first time.

Es importante leer este manual antes de usar por vez primera su equipo.

RP5605

v2.0 (EN/E)

FCC information

This device complies with Part

15 of the FCC Rules. Operation

is subject to the following two

conditions: (1) This device may not

cause harmful interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

This equipment has been tested

and found to comply with the

limits for a Class B digital device,

pursuant to Part 15 of FCC Rules.

These limits are designed to

provide reasonable protection

against harmful interference in

a residential installation. This

equipment generates, uses, and

can radiate radio frequency

energy and, if not installed

and used in accordance with

the instructions, may cause

harmful interference to radio

communications.

However, there is no guarantee

that interference will not occur

in a particular installation. If

this equipment does cause

harmful interference to radio or

television reception, which can

be determined by turning the

equipment off and on, the user is

encouraged to try to correct the

interference by one or more of

the following measures:

•

Reorient or relocate the

receiving antenna.

•

Increase the separation

between the equipment and

receiver.

•

Connect the equipment into

an outlet on a circuit different

from that to which the

receiver is connected.

•

Consult the dealer or

an experienced radio/TV

technician for help.

Changes or modifications not

expressly approved by the party

responsible for compliance could

void the user’s authority to

operate the equipment.

Technical information

Product: CD/Clock Radio

Brand: RCA

Model: RP5605-A

Power Supply: 120V ~ 60Hz

Power Consumption: 13 Watts

Service information

This product should be serviced

only by those specially trained in

appropriate servicing techniques.

For instructions on how to obtain

service, refer to the warranty

included in this user manual.

The descriptions and characteristics in this owner’s manual are for the purpose of

general reference only and not as a guarantee. In order to provide you with the

highest quality product, we may make changes or modifications without prior notice.

The English version serves as the final reference on all product and operational details

should any discrepancies arise in other languages.

PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE

IMPORTANT SAFETY INSTRUCTIONS

Before you begin

General controls

Clock

Limited warranty

WARNING:

TO PREVENT FIRE OR ELECTRICAL

SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

Sleep function

Audiovox Electronics Corp

150 Marcus Blvd, Hauppauge, NY 11788

1-877-833-3491

©2008

Trademark(s) ® Registered

Marque(s) ® Deposée(s)

Marca(s) ® Registrada(s)

www.rcaaudiovideo.com

Important Battery Precautions

• Any battery may present a risk

of fire, explosion, or chemical

burn if abused. Do not try to

charge a battery that is not

intended to be recharged, do

not incinerate, and do not

puncture.

• Non-rechargeable batteries,

such as alkaline batteries, may

leak if left in your product for

a long period of time. Remove

the batteries from the product

if you are not going to use it

for a month or more.

• If your product uses more

than one battery, do not mix

types and make sure they are

inserted correctly. Mixing types

or inserting incorrectly may

cause them to leak.

• Discard any leaky or deformed

battery immediately. They

may cause skin burns or other

personal injury.

• Please help to protect the

environment by recycling

or disposing of batteries

according to federal, state, and

local regulations.

]

Plugging in for power

AC OUTLET POWER SUPPLY:

120V~60Hz

The AC power plug is

polarized (one blade is

wider than the other)

and only fits into AC

power outlets one way.

If the plug will not go into the

outlet completely, turn the plug

over and try to insert it the other

way.

If it still does not fit, contact

a qualified electrician to change

the outlet, or use a different one.

Do not attempt to bypass this

safety feature.

Power is fed to the unit even

when it is not functioning. To cut

the power supply off, the power

cable must be unplugged.

Top view

Radio

If you set Sleep function

with low volume level

before going to bed, we

advise using Wake to Alarm

mode.

Limited Warranty (US)

What your warranty covers:

• Defects in materials or

workmanship.

For how long after your purchase:

• One year from date of

purchase.

• The warranty period for rental

units begins with the first

rental or 45 days from date of

shipment to the rental firm,

whichever comes first.

What we will do:

• Provide you with a new, or at

our option, a refurbished unit.

The exchange unit is under

warranty for the remainder of

the original product’s warranty

period.

• Proof of purchase in the form

of a bill of sale or receipted

invoice which is evidence

that the product is within

the warranty period must be

presented to obtain warranty

service. For rental firms, proof

of first rental is also required.

How to make a warranty claim:

• Properly pack your unit.

Include any cables, etc., which

were originally provided with

the product.

We recommend

using the original carton and

packing materials.

• Include evidence of purchase

date such as the bill of sale.

Also print your name and

address and a description of

the defect.

Send via standard

UPS or its equivalent to:

Thomson Inc.

Product Exchange Center

11721 B Alameda Avenue

Socorro, Texas 79927

• Insure your shipment for loss

or damage. Thomson accepts

no liability in case of damage

or loss en route to Thomson.

• Pay any charges billed to you

by the Exchange Center for

service not covered by the

warranty.

• A new or refurbished unit

will be shipped to you freight

prepaid.

What your warranty does not

cover:

• Customer instruction. (Your

Owner’s Manual provides

information regarding

operating Instructions and

user controls.

For additional

information, ask your dealer.)

• Installation and set-up service

adjustments.

• Batteries.

• Damage from misuse or

neglect.

• Products which have been

modified or incorporated into

other products.

• Products purchased or serviced

outside the USA.

• Acts of nature, such as but not

limited to lightning damage.

Product Registration:

• Please complete and mail

the Product registration Card

packed with your unit.

It will

make it easier to contact you

should it ever be necessary.

The return of the card is

not required for warranty

coverage.

Limitation of Warranty:

• THE WARRANTY STATED

ABOVE IS THE ONLY

WARRANTY APPLICABLE TO

THIS PRODUCT.

ALL OTHER

WARRANTIES, EXPRESS OR

IMPLIED (INCLUDING ALL

IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE)

ARE HEREBY DISCLAIMED.

NO VERBAL OR WRITTEN

INFORMATION GIVEN BY

THOMSON INC., ITS AGENTS

OR EMPLOYEES SHALL CREATE

A GUARANTY OR IN ANY WAY

INCREASE THE SCOPE OF THIS

WARRANTY.

• REPAIR OR REPLACEMENT

AS PROVIDED UNDER THIS

WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER.

THOMSON INC. SHALL NOT

BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL

DAMAGES RESULTING FROM

THE USE OF THIS PRODUCT

OR ARISING OUT OF ANY

BREACH OF ANY EXPRESS OR

IMPLIED WARRANTY ON THIS

PRODUCT.

THIS DISCLAIMER

OF WARRANTIES AND LIMITED

Battery back-up operation

The power failure protection

circuit will not operate unless

battery is installed.

No worry battery backup

When the battery backup

functions, the digital display will

not light, however, the wake

function still occurs during the

power interruption if remaining

battery power is adequate.

Normal operation will resume

after AC power is restored so you

will not have to reset the time or

wake.

Install battery as follow:

1. Remove battery compartment

door (located at the bottom of

the radio) by applying thumb

pressure to the tab on battery

door and then lift the door

out and off the cabinet.

2. Connect a 9-volt battery (not

supplied) to the connector

plug.

3. Replace the compartment door.

Power failure indicator

When AC power is interrupted

(disconnected) for a short period

of time, both time and alarm

settings will change (unless

battery is installed). After AC

power is restored (reconnected),

the Digital Display will blink

to indicate that power was

interrupted and you should

readjust the time and alarm

settings.

Left view

Right view

TUNING

– selects radio frequency

BAND AM/FM

– selects radio

band

WARRANTY ARE GOVERNED

BY THE LAWS OF THE STATE

OF INDIANA.

EXCEPT TO

THE EXTENT PROHIBITED

BY APPLICABLE LAW, ANY

IMPLIED WARRANTY OF

MERCHANTABILITY OR

FITNESS FOR A PARTICULAR

PURPOSE ON THIS PRODUCT IS

LIMITED TO THE APPLICABLE

WARRANTY PERIOD SET FORTH

ABOVE.

How state law relates to this

warranty:

• Some states do not allow the

exclusion nor limitation of

incidental or consequential

damages, or limitations on

how long an implied warranty

lasts, so the above limitations

or exclusions may not apply to

you.

• This warranty gives you specific

legal rights, and you also may

have other rights that vary

from state to state.

If you purchased your product

outside the USA:

• This warranty does not apply.

Contact your dealer for

warranty information.

Switching on

Press

RADIO ON

to turn on the

radio.

Switching band

Slide the

BAND/AM•FM

switch on

the right of the unit to select AM

or FM band.

Tuning radio

Rotate the

TUNING

dial on the

right of the unit to select radio

frequency.

Antennas

AM Antenna

– A built-in ferrite

rod antenna eliminates the need

for an outside antenna for AM

reception.

Rotating the unit

slightly may improve reception of

distant AM stations.

FM Antenna

– The power cord

acts as your FM antenna.

The

power cord picks up moderate

to strong stations and eliminates

the need for an external antenna

in most strong signal areas.

Be

sure the power cord is stretched

out to its full length.

Do not

coil or bunch the cord together.

Changing position of the power

cord may improve reception.

Built-In AFC

– The Built In

Automatic Frequency Control

(AFC) works only on FM. It helps

reducing drift on FM reception

and keeping the radio locked in

on the FM station to which it is

tuned.

When tuning in FM stations, you

may notice that the station you

are tuning can be well-tuned on

two or three nearby points on the

dial. Always tune carefully at the

loudest and clearest point.

Wake function

Setting wake time

1. Press

WAKE TIME

once. The

current wake time flashes on

the display.

2. Press

or

to set the wake

time. The time decrements or

increments will follow by a

faster rate when you press and

hold the buttons. AM or PM

indicator also lights beside the

time on the display.

3. When finished, wait for about

5 seconds or press

WAKE

TIME

to exit wake time setting

mode.

• The Wake to Alarm mode

(read below) will be

automatically activated

whenever the wake time has

been set.

Selecting wake source

1. If your desired wake source is

radio or CD:

• Wake to Radio – select an

AM or FM station (refer to

“Radio”).

• Wake to CD – insert a CD in

the CD compartment.

2. Set a wake time (refer to

“Setting wake time”).

3. Press

WAKE MODE

repeatedly

to select a wake source. The

indicator lights against the

wake source icons on the right

of the display to indicate the

currently selected wake source:

• Once the wake source is

selected, the wake function

will be activated at the set

wake time.

You can set the duration (up to 90

min) before the radio or CD player

turns off automatically.

1.

Press

SLEEP

repeatedly to

select a duration (90, 80, 70,

60, 50, 40, 30, 20, 10min or

OFF) before the radio or CD

player turns off automatically.

• The default sleep time is 60

minutes.

• By default, the radio will be

switched on once

SLEEP

is

pressed. You may change to

listen to the CD player by

pressing

if a disc is loaded.

2. To check the remaining

duration before the unit turns

off, press

SLEEP

once.

3. To cancel the sleep function,

press

SNOOZE

or

OFF

.

Alkaline (NEDA 1604A/

IEC 6LR61) battery is

recommended. Carbon-

zinc battery may be used but

memory holding time will

be substantially reduced.

Memory holding time for

a fresh alkaline battery is

approximately 8 hours (if radio

or alarm are not operated)

which should take care of

short, nuisance-type AC power

failures. To preserve battery

life, the unit should remain

plugged into an AC outlet.

As the battery gets older, its

voltage drops and memory may

be lost. Be sure to replace the

battery periodically. Battery

should be removed if the unit

will be stored for more than

one month. Leaky battery can

badly damage the clock radio.

Some of the following

information may not apply to

your particular product; however,

as with any electronic product,

precautions should be observed

during handling and use.

•

Read these instructions.

•

Keep these instructions.

•

Heed all warnings.

•

Follow all instructions.

•

Do not use this apparatus near

water.

•

Clean only with dry cloth.

•

Do not block any ventilation

openings. Install in accordance

with the manufacturer’s

instructions.

•

Do not install near any heat

sources such as radiators, heat

registers, stoves, or other

apparatus (including amplifiers)

that produce heat.

•

Do not defeat the safety

purpose of the polarized

or grounding-type plug. A

polarized plug has two blades

with one wider than the

other. A grounding type plug

has two blades and a third

grounding prong. The wide

blade or the third prong is

provided for your safety. If

the provided plug does not

•

Do not attempt to disassemble

the cabinet. This product

does not contain customer

serviceable components.

•

IF YOUR PRODUCT OPERATES

ON BATTERIES, adhere to the

following precautions:

A. Any battery may leak

electrolyte if mixed with

a different battery type, if

inserted incorrectly, or if all

batteries are not replaced at

the same time.

B. Any battery may leak

electrolyte or explode if

disposed of in fire or an

attempt is made to charge a

battery not intended to be

recharged.

C. Discard leaky batteries

immediately. Leaking batteries

can cause skin burns or

other personal injury. When

discarding batteries, be sure

to dispose of them in the

proper manner, according to

your state/provincial and local

regulations.

For your records

In the event that service should be

required, you may need the model

number and the serial number.

In

the space below, record the date

and place of purchase and the

serial number:

Model No.:

Date of Purchase:

Place of Purchase:

Serial No.:

RADIO ON

– turns on the radio;

selects the radio from other

modes

OFF

– turns off the unit; turns off

the wake function and sleep mode

/

– sets clock or wake time;

skips to previous or next CD track

during CD playback

– stops CD playback

– turns on the unit from CD

mode; pauses or resumes CD

playback

SLEEP

– activates the Sleep

function

CLOCK SET

– activates clock time

setting mode

WAKE TIME

– activates wake

time setting mode; checks current

wake time

WAKE MODE

– activates wake

function and changes wake mode

SNOOZE

– turns off the wake

function temporarily; cancels the

sleep function

+ VOLUME

–

– adjusts volume

CD player

Listening to CD

1. Lift open the CD compartment

door.

2. Insert a disc and close the

door.

3. Press

to select CD mode and

start CD playback.

• Press

to pause playback and

press again to resume.

4. Adjust volume to your desired

level.

5. Press

or

to skip backward

or forward a track. Press and

hold to search through a track.

6. Press

to stop playback.

7. Press

RADIO ON

to listen to

the radio or

OFF

to turn off

the unit.

wake by alarm

wake by radio

wake by CD

Turning off the wake

function

Silence the wake function

momentarily:

• With SmartSnooze™, press

SNOOZE

,

,

,

or

to

turn off the wake function

temporarily for extra sleep

time.

• The wake function will activate

again when the snooze period

(9 minutes) is over.

•

The snooze period is fixed and

cannot be changed.

Checking wake time

Press

WAKE TIME

to show the

current wake time which flashes

briefly on the display.

• If disc is paused for

more than 5 minutes,

the CD player will

resume to stop mode

automatically.

• If disc is stopped in the CD

mode for more than 30

minutes without further

operations, the unit will

turn off automatically.

SEE MARKING ON BOTTOM OF PRODUCT

RCA RP5605 User Manual - RP5605

RCA RP5605 - RP CD Clock Radio Manual

RCA RP5605 manual content summary: