RCA RT2760 User Manual - RT2760 - Page 1
RCA RT2760 Manual
UPC - 044319504125
View all RCA RT2760 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
RT2760 EN B ver. 4/4/06 11:31 AM Page 1 FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Inc. could void the user's authority to operate this product. This device generates and uses radio frequency (RF) energy, and if not installed and used properly, this equipment may cause interference to radio and television reception. If this equipment does cause interference to radio or television reception (which you can determine by unplugging the unit), try to correct the interference by one or more of the following measures: • Re-orient the receiving antenna (that is, the antenna for the radio or television that is "receiving" the interference). • Move the unit away from the equipment that is receiving interference. • Plug the unit into a different wall outlet so that the unit and the equipment receiving interference are on different branch circuits. If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, "How To Identify and Resolve Radio TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. Please specify stock number 004-00000345-4 when ordering copies. This product complies with DHHS Rules 21 CFR Subchapter J. Applicable at the date of manufacture. Main plug is used as the disconnect device,it shall remain readily operable and should not be obstructed during intended used.To be completely disconnected the apparatus from supply mains,the main plug of the apparatus shall be disconnected from the mains socket outlet completely. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN T H E L I G H T N I N G CAUTION: TO REDUCE THE THE EXCLAMATION FLASH AND ARROW- RISK OF ELECTRIC SHOCK, POINT WITHIN THE HEAD WITHIN THE DO NOT REMOVE COVER T R I A N G L E I S A T R I A N G L E I S A ( O R B A C K ) . N O U S E R - WARNING SIGN WA R N I N G S I G N SERVICEABLE PARTS IN- ALERTING YOU OF ALERTING YOU OF SIDE. REFER SERVICING I M P O R T A N T " D A N G E R O U S TO QUALIFIED SERVICE I N S T R U C T I O N S VOLTAGE" INSIDE PERSONNEL. A C C O M PA N Y I N G THE PRODUCT. T H E P R O D U C T. SEE MARKING ON BOTTOM / BACK OF PRODUCT WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Technical Specification Product: Dolby Digital Audio Receiver Brand: RCA Model: RT2760 Electrical current consumption Power Supply: 120V ~ 60Hz Power consumption: 170 Watts IMPORTER Comercializadora Thomson de México, S.A. de C.V. Álvaro Obregón No. 151. Piso 13. Col. Roma. Delegación Cuauhtémoc C.P. 06700. México, D.F. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5 For Your Safety The AC power plug is polarized (one blade is wider than the other) and only fits into AC power outlets one way. If the plug won't go into the outlet completely, turn the plug over and try to insert it the other way. If it still won't fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. For Your Records In the event that service should be required, you may need both the model number and the serial number. In the space below, record the date and place of purchase, and the serial number: Model No. Remote Control No. Date of Purchase Place of Purchase Serial No. Service Information This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this Guide Getting Started Unpacking the Receiver You should receive the following items: • One receiver unit • One pair of "AAA" batteries • One pig-tail antenna wire • One external AM loop antenna • One digital in cable (coaxial in) • One 3.5mm stereo cable for line-in • One instruction book • One safety leaflet • Quick Connection Guide • One Remote Control Set up and Maintenance of the Receiver Provide spaces for sufficient ventilation as indicated: Unpacking The Speakers One set of speakers including: • One set of left and right front speakers, • One centre speaker, • One subwoofer and • One set of left and right rear speakers front speakers GEFAHR EINES ELEKTRISCHEN SCHLAGS subwoofer rear speakers centre speaker Inserting Batteries into Remote Control Insert two "AAA" (R03) batteries according to the + and - signs in the battery compartment. To use the remote control, point it directly at your receiver. Install batteries as follows: 1. Remove battery compartment door by applying thumb pressure on battery door and then lift the door out and off the cabinet. 2. Insert 2 AAA batteries in the compartment and replace the compartment door. • Do not connect to the AC power cords until all connections are completed. • Do not use your set immediately after transferring it from a cold place to a warm place: there is risk of condensation. • Do not expose your set to water and excessively high temperatures. • After having disconnected your set, clean the case with a soft cloth, or with a slightly damp leather chamois. Never use strong solvents. Protect your Components from Overheating • Do not block ventilation holes in any component. Arrange the components so that air can circulate freely. • Do not stack components directly on top of each other. • Do not place the unit near other components that generate heat such as heating vents. • Allow adequate ventilation when placing your components in a stand. • Place an amplifier near the top shelf of the stand so heated air rising from it will not affect other components. If you have a satellite receiver, you should place it on the top shelf. Getting Started Digital Connections Read instructions carefully when connecting components to the receiver. Digital In Jacks can accept Dolby Digital (AC-3) or PCM signals when compatible components are connected. NOTE The system is equipped with Dolby Digital, and manufactured under License from Dolby Laboratories. Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. TV Connections TVs with RF input may need a RF modulator (not included) for inputting audio signals. TV Connecting the Antennas Connect the AM and FM antennas to the AM and FM terminals on the system's back panel. They must be hooked up in order to receive clear reception. AM Loop Antenna and FM Indoor Antenna 1. Uncoil the antenna wire and locate the base end of the AM antenna. 2. Press down on the antenna tab to open the terminal. 3. Insert the antenna wires into the terminal and release the tabs to secure the wires in place. NOTE Make sure the white wire on the AM loop antenna is inserted into the AM LOOP terminal. HINT • For FM reception, extend antenna to its full length. • For AM reception, rotate the antenna horizontally to get better reception. Connecting the speakers Connecting for Power Make sure you connect all your other electronic components and the speakers before plugging your receiver into the outlet. Plug the power cord in the wall outlet, matching the wide blade of the plug with the wide slot in the outlet. Be sure to insert the plug completely. Using Headphones To listen privately through your audio system, use the PHONES jack on the receiver. However, make sure you turn down the volume before you put on the headphones. Increase the volume to the desired level after headphones are in place. Once the headphones are connected, "HEADPHONE DOWN MIX 2 CHANNEL"will scroll on display. This feature automatically converts multi-channel speaker outputs to 2 channel stereo for your listening pleasure. Hearing Comfort & Well-Being • Do not play your headset at a high volume. Hearing experts advise against continuous extended play. • If you experience a ringing in your ears, reduce volume or discontinue use. Factory Setting The unit is preset to the following settings when you first power the receiver up right out of the box: Function = AM/FM Volume setting = 25 Bass & treble = 0 dB EQ - FLAT Speaker settings: Center, surr = YES Subwoofer = BALANCE DRC = OFF NOTE BALANCE SUBWOOFER setting makes the output level of subwoofer speaker to be balance with the normal Dolby setting. Adjust the SUBWOOFER setting by pressing the SUBWOOFER key to achieve the best bass performance. Reset to Factory Settings You may restore factory setting with the following procedures: WARNING All preset radio stations and surround sound setting will be lost after factory setting is restored. 1. Enter STANDBY mode. 2. Press PRESET + , PRESET - , SURROUND DOWN to reset the unit. All preset stations will reset to FM87.5MHz and all receiver settings restore to default settings as described above. Connecting to Audio Components COAXIAL OPTICAL DVD SAT/CAB Six speakers are provided with the unit (2 front, 1 center, 2 rear, 1 subwoofer). To achieve good surround effects, all six speakers need to be connected to the receiver. Speaker wires are color-coded to match the terminals. NOTE When connecting the speakers, make sure the polarities ("+" speaker wire to "+" on the receiver. For example, red wire to red terminal on the receiver) of speaker wires and terminals match. If the cords are reversed, the sound will be distorted. Do not ground the output line, it will damage the speaker. NOTE When connecting subwoofer, connect subwoofer control cable to the unit's rear panel first, then press the power switch on the subwoofer speaker to switch it on. user manual IMPORTADOR Comercializadora Thomson de México, S.A. de C.V. Álvaro Obregón No. 151. Piso 13. Col. Roma. Delegación Cuauhtémoc C.P. 06700. México, D.F. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5 EXPORTER Thomson Inc. P.O. Box 1976 Indianapolis, IN 46206 - 1976 © 2006 Thomson Inc. Trademark(s) ® Registered Marca(s) Registrada(s) Marque(s) Deposée 5626420B www.rca.com Printed in China / Impreso en China RT2760 It is important to read this instruction book prior to using your new product for the first time. Es importante leer este manual antes de usar por vez primera su euipo. Operating Your Receiver Receiver Controls 13 8 9 10 2 4 6 75 1. ON/STANDBY Turns the unit on and off. When the system is turned on, the unit will go to the mode it was in before powered off. 2. Play/Pause Starts and pauses playback in USB mode. 3. Stop Stops playback in USB mode. 4. PRESET Buttons (PREV/NEXT) Selects preset stations in AM/FM mode. Directly accesses the previous or next track in USB mode. 5. SURROUND Buttons Select digital sound processor. (DOLBY PL II MOVIE, STEREO, DISCO, STADIUM, THEATER, JAZZ CLUB, ARENA, 3 STEREO, DOLBY PL EMULATION, DOLBY PL II MUSIC) 6. USB Slot Connects USB devices. 7. LINE IN Connects components for audio input. 8. SOURCE Buttons Select sound source. (DVD/DVR, TV, SAT.CAB, AM/FM, VCR, USB and LINE-IN) 9. VOLUME Increases and decreases volume level 10. SUBWOOFER Selects among subwoofer sound level. (SOFT SUBWOOFER, BALANCE SUBWOOFER, STRONG SUBWOOFER, POWERFUL SUBWOOFER) 11. PHONES Plug your headphones (not supplied) into it for your private enjoyment. Speakers will be off when phones are inserted. Remote Control Please be sure you have inserted the batteries into the remote control. You can test it by pressing any button. 1 2 5 6 7 3 8 4 9 10 11 12 14 13 15 16 11 4. MONO/ST Selects between Stereo and Mono sound in FM mode. 5. TEST TONE Speaker Test tone setting. Refer to "Advanced Sound Control" for details. 6. NIGHT Selects among Night mode options (DRC OFF, SOFT and ON) which compresses the volume difference between normal voices and sounds such as explosions. (Available only during Dolby digital signal playback) 7. EQ Selects among preset Equalizer mode. (only available in stereo mode) 8. SURROUND Selects digital sound processor. (DOLBY PL II MOVIE, STEREO, DISCO, STADIUM, THEATER, JAZZ CLUB, ARENA, 3 STEREO, DOLBY PL EMULATION, DOLBY PL II MUSIC) 9. SETUP Enters Setup mode. Use the Left and Right adjustment buttons to select among setup options. (DIMMER, CENTER SPK ON/OFF, SURROUND SPK ON/OFF, FRONT SURROUND ON/OFF and DIGITAL INPUT). 10. DISTANCE Adjusts the speakers' distance. 11. Adjustment Buttons • Press the Left or Right buttons to select among setting items in setup mode: DIMMER, SPEAKER DISTANCE, SPEAKER SETUP, FRONT SURROUND ON/OFF and audio input source (OPTICAL / COAXIAL). • Press the Up or Down buttons to adjust the values when the display shows the setup you want to change. In AM/FM mode: • Press the TUNER - and TUNER + keys to tune down or up the radio frequency. 12. MUTE Mutes all audio output. 13. SUBWOOFER Selects among subwoofer sound level. (SOFT SUBWOOFER, BALANCE SUBWOOFER, STRONG SUBWOOFER, POWERFUL SUBWOOFER) 14. LEVEL Speaker LEVEL setting. Refer to "Advanced Sound Control" for details. 15. VOL + / VOL - (Volume Buttons) Adjusts the volume level. 17 18 19 22 20 21 23 Operating Your Receiver 16. CH+ / CH- (PREV/NEXT) Selects programmed stations in AM/FM mode. Directly accesses the next or previous file in USB mode. 17. Operation Buttons • PLAY,STOP and PAUSE keys are only for control of USB device. • Press REV or FWD starts reverse or forward accelerated play in USB mode. 18. DISPLAY Accesses MP3/WMA ID3 information and current play time,current play Folder and Track number,Play Mode in USB mode. 19. REPEAT Accesses the repeat function in USB mode. 20. RANDOM Turns on/off random playback in USB mode. 21. INTRO Enters intro mode in USB mode. 22. SLEEP Enters sleep mode and selects sleep time. 23. Source Buttons Selects various audio sources. Switching the unit on and off • To switch on the receiver, press the ON/STANDBY button on the main unit once, or the ON•OFF button on the remote control. Selection of source When one of the source buttons in front panel is pressed, the input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. Example 1: If you have connected a DVD player to the DVD input on the receiver, press the DVD/DVR buttons on the front panel to receive the sounds transmitted by the DVD. Example 2: Based on the example 1, the DVD is playing , if a VCR is connected to the VCR input of the receiver, press the VCR button on the front panel. The sound from the VCR source will replace the DVD. You can connect up to 6 audio sources to this amplifier: Source button Corresponding connector (receiver front panel) (receiver back panel) - DVD/DVR - TV - SAT.CAB - FM/AM - VCR - USB - LINE IN DVD IN TV IN SAT/CAB IN built-in VCR IN USB Slot (front panel) Line In Slot (front panel) The source name selected shown on the display. Example: Press DVD/DVR to select DVD as the source to the amplifier. NOTE 1. Your receiver has a built in tuner. Just connect the appropriate antenna to the back of the receiver and you will be able to listen to radio stations. (See details in Tuner section) 2. Other sources can be connected to the above standard source. Example: you can connect a LD into the DVD inputs. 3. Connections at the back panel can be intercahnged if sources have the same audio input. Example, you can connect a TV to VCR inputs and connect a VCR to TV input. 4. Refer to the "Connecting To Audio Components" section for details on connection. Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details). 2. Press ON/STANDBY on the main unit or press ON•OFF on the remote control to switch on the receiver. 3. Press the DVD/DVR button on the main unit to select the DVD source. 4. Switch ON the DVD player and start playback. 5. Set the sound mode if needed (see "Advanced sound control" for details). Example 1: To play Dolby Prologic II Movie sound, press the SURROUND buttons until "Dolby PL II MOVIE" appears on the Display. Example 2: LD: You may need to select a different Audio Channel on your LD (refer to your LD player manual). 6. Adjust the volume knob accordingly. NOTE To play Dolby Digital sound, the source must be connected to the receiver via the optical or coaxial terminal. 1. ON•OFF Turns the receiver on and off. 2. Number Buttons Directly accesses a preset station in AM/FM mode. 3. MEMORY Stores station in AM/FM mode.