RCA RTD316Wi RTD316Wi Product Manual

SURROUND:

Changes the Surround sound

setting. Press the button to select

between 5.1CHANNEL and STEREO

modes. (Refer to details on“Sound

Enhancement Systems”)

Remote Control Functions in Tuner Mode

TUNER:

Select the TUNER and switch be-

tween FM/AM.

VOL+/–:

Adjust the sound volume.

MUTE:

Mute and restore the sound.

TUNER +/–:

Tune down and up the radio fre-

quencies.

MEMORY:

Store a station.

CH

+/

/

CH

–/

: Select programmed stations.

AUDIO:

Select

between

Stereo

and

Mono mode for Tuner (FM).

Using Remote Control to Navigate through

the On-Screen Menus

Use

,

,

,

buttons

and OK on the remote

control to navigate through the on-screen dis-

plays (the DVD player’s menu, the Info Display that

appears during playback, or a disc’s menu).

Use

,

,

,

buttons

on the remote control

to move through on-screen menus in the direc-

tion of the button (e.g., to move right, press

).

The buttons are used to highlight an option. Once

highlighted, press OK to select the option that is

highlighted.

Types of Menus

• Disc menu — The appearance and contents of

this menu varies according to the type of disc

you have inserted. It is separate from the Setup

menu.

•

Info menu — The unit’s Info menu appears at

the top of the screen while the disc is playing.

Press

INFO on the remote control to switch the

Info menu on or off.

• Setup menu — Press SETUP to access

this

menu.

USER MANUAL

RTD316Wi

It's important to read this instruction prior to using your new product for the first time.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the

•

equipment and receiver.

Connect the equipment into an outlet on

•

a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio /

•

TV technician for help.

WARNING:

Changes or modifications to this unit

not expressly approved by the party responsible

for compliance could void the user's authority to

operate the equipment.

Safety Precautions

Connections and Setup


Overview of Controls - Front Panel Controls

Overview of Controls

Overview of Controls

Playing Discs - Basic Functions

Basic Playback Operations



Safety Precautions

Important Information

Important Safety Instructions

This Home Theater has earned

the ENERGY STAR.

This product complies with DHHS Rules 21 CFR

Subchapter J.

Applicable at the date of manufac-

ture.

Ventilation

You must adequately ventilate the product. Make

sure there is adequate space around the unit to

provide proper air flow for ventilation. See dia-

gram.

For your Safety

The AC power plug is polar-

ized (one blade is wider than

the other) and only fits into

AC power outlets one way.

If the plug won’t go into the

outlet completely, turn the

plug over and try to insert it the other way.

If it still won’t fit, contact a qualified electrician to

change the outlet, or use a different one. Do not

attempt to bypass this safety feature.

Removing the power plug is the only way to com-

pletely remove power from your product. Make

sure the power plug remains easily accessible.

Note:

This DVD player is designed and manufactured to

respond to the Region Management Information.

If the Region number of a DVD disc does not cor-

respond to the Region number of this DVD player,

this player cannot play the disc. The Region num-

ber for this DVD player is Region 1.

THE LIGHTNING FLASH AND ARROWHEAD

WITHIN THE TRIANGLE IS A WARNING SIGN

ALERTING YOU OF “DANGEROUS VOLTAGE”

INSIDE THE PRODUCT.

THE EXCLAMATION POINT WITHIN THE

TRI-

ANGLE IS A WARNING SIGN ALERTING YOU OF

IMPORTANT INSTRUCTIONS ACCOMPANYING

THE PRODUCT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSON-

NEL.

WARNING:

TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION:

DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH

THE SAME OR EQUIVALENT TYPE.

WARNING:

TO BE COMPLETELY DISCONNECT THE POWER INPUT ,

THE MAINS PLUG OF APPARA-

TUS SHALL BE DISCONNECTED FROM THE MAINS.

THE MAINS PLUG OF APPARATUS SHOULD NOT

BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED DURING INTENDED USE.

Service Information

This product should be serviced only by those

specially

trained

in

appropriate

servicing

techniques.

Main plug is used as the disconnect device,

it shall remain operable and should not be

obstructed during intended use. To be completely

disconnected the apparatus from supply mains, the

main plug of the apparatus shall be disconnected

from the mains socket outlet completely.

Caution

Invisible laser radiation when open and interlocks

defeated. Avoid exposure to beam. Class 1 laser

product.

This system must be opened only by qualified

technicians to prevent accidents caused by the

laser beam.

DVD Copy Protection

In accordance with the DVD standard, your DVD

player is equipped with a Copy Protection system,

which can be switched on and off by the DVD

disc itself, in order to make any recording of the

relevant DVD disc onto a videotape of very poor

picture quality, or even impossible. This product

incorporates copyright protection technology

that is protected by method claims of certain U.S.

patents and other intellectual property rights

owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home use only

unless otherwise authorized by Macrovision

Corporation Reverse engineering or disassembly

is prohibited.

Important Battery Information

•

Do not mix different types of batteries or new and

old batteries. Do not use rechargeable batteries.

•

In order to avoid any risk of explosion, observe

the polarities indicated inside the battery

compartment. Replace only with the type of

batteries specified. Do not dispose of them in a

fire or recharge them.

•

If you are not using the remote control for a long

period of time, remove the batteries.

Illustrations contained in this document are for

representation only.

Please respect the environment and

prevailing regulations. Before you

dispose of batteries or accumula-

tors, ask your dealer whether they

are subject to special recycling and

if they will accept them for disposal.

WARNING

To reduce the risk of fire or electric shock,

do not expose this product to rain or mois-

ture. No objects filled with liquids, such as

vases, should be placed on the apparatus.

CAUTION:

This product utilizes a laser. Use of controls or

adjustments or performance of procedures other

than those specified may result in hazardous

radiation exposure. Do not open covers and do

not repair yourself. Refer servicing to qualified

personnel.

This Class B digital apparatus complies

with Canadian ICES-003.

Cet appareil numérique de la classe B

est conforme à la norme du NMB-003 du

Canada.

Please Read and Save for Future Reference.

Some of the following information may not apply

to your particular product; however, as with

any electronic product, precautions should be

observed during handling and use.

Read these instructions.

•

Keep these instructions.

•

Heed all warnings.

•

Follow all instructions.

•

Do not use this apparatus near water.

•

Clean only with a dry cloth.

•

Do not block any ventilation openings.

•

Install in accordance with the manufacturer’s

instructions.

Do not install near any heat sources such

•

as radiators, heat registers, stoves, or other

apparatus (Including amplifiers) that produce

heat.

Only use attachments / accessories specified by

•

the manufacturer.

Do not defeat the safety purpose of the

•

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong is provided for your safety.

If the provided plug does not fit into your wall

outlet, consult an electrician for replacement of

the obsolete outlet.

Protect the power cord from being walked on

•

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

Unplug this apparatus during lightning storms

•

or when unused for long periods of time.

Use only with a cart, stand, tripod, bracket, or

•

table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Refer all servicing to qualified service personnel.

•

Servicing is required when the apparatus has been

damaged in any way, such as the

power cord or plug is damaged,

liquid has been spilled or objects

have fallen into the apparatus, the

apparatus has been exposed to

rain or moisture, does not operate

normally, or has been dropped.

Additional Safety Information

•

The apparatus shall not be exposed to dripping or

splashing and that no objects filled with liquids,

such as vases, shall be placed on the apparatus.

•

Always leave sufficient space around the product

for ventilation. Do not place product in or on a bed,

rug, in a bookcase or cabinet that may prevent

air flow through vent openings.

•

Do not place lighted candles, cigarettes, cigars,

etc. on the product.

•

Connect power cord only to AC power source as

marked on the product.

•

Care should be taken so that objects do not fall

into the product.

•

Do not attempt to disassemble the cabinet. This

product does not contain customer serviceable

components.

If your product operates on batteries, adhere to

the following precautions:

A. Any battery may leak electrolyte if mixed with a

different battery type, if inserted incorrectly, or if

all batteries are not replaced at the same time.

B. Any battery may leak electrolyte or explode if

disposed of in fire or an attempt is made to charge

a battery not intended to be recharged.

C. Discard leaky batteries immediately. Leaking

batteries can cause skin burns or other personal

injury. When discarding batteries, be sure to

dispose of them in the proper manner, according

to your state/provincial and local regulations.

D. Battery shall not be exposed to excessive heat

such as sunshine, fire or the like.

•

Other important use and cleaning information

at the end of the booklet.

Connecting the Antennas

The AM and FM antennas connect to the AM and

FM terminals on the system’s back panel. They

must be hooked up in order to receive clear re-

ception.

AM Loop Antenna

1. Uncoil the AM antenna wire.

2. Press down on the antennas tab to open the

terminal.

3. Make sure the white wire on the AM loop

antenna is inserted into the AM loop terminal

and the other wire is inserted into the ground

loop terminal.

Connecting to Your TV (VIDEO)

Method 1

Method 2

Method 1

Composite video jack (yellow)

•

The basic video jack is color-coded yellow.

• Video cable (yellow) is supplied for the

connection for good picture quality.

• Connect the video OUT jack on the receiver

to the

Video IN jack on your TV so the video

content goes from the receiver to the screen.

Method 2

Component video jacks (Pr, Pb, Y)

• The component video jacks are color-coded

green, blue and red.

• Additional component video cables (not

supplied) are required to provide best picture

quality. They are usually color-coded green, blue

and red.

•

Connect the component video OUT jacks on the

receiver to the component video IN jacks on your

TV so the video content goes from the receiver

to the screen.

•

If your television is a high definition

television, use the unit’s HDMI

output to get the highest possible video

resolution. If unable to use a HDMI

connection, use the unit’s component

video output and set the Progressive Scan

option in the Video menu to ON, to get the

next highest possible video resolution.

•

If one of the devices is not working,

check

that all the cables have been inserted

properly into the jacks.

•

If your component has only one input for

audio (mono), connect it to the left (white

L/Mono) audio jack on the TV and don’t

connect the right audio part of the cable.

Connecting to Your TV (via HDMI input)

HDMI stands for High Definition Multimedia In-

terface. HDMI transfers digital audio and uncom-

pressed digital video on a single cable.

Press the HDMI button on the remote control to

change output signals as follows: 480p, 720p,1080i

and 1080p.

Connecting

AUDIO

from

External

Sources such as TV

Using AUDIO IN Jack

Connect the Ø3.5mm AUDIO IN jack on the front

panel of the unit to the headphone output on

mp3 players.

Notes:

• Ø3.5mm to Ø3.5mm audio cables (not

included).

•

To listen to the audio input from the connected

component, press SOURCE on the main unit or

AUDIO/AUX on the remote control to select the

AUDIO IN mode.

Using AUX

Jacks

Connect the AUX jacks from the unit to the AUDIO

OUT jacks on VCR, TV, SAT/Cable Box or other

component. Press either SOURCE on the main unit

or AUDIO/AUX on the remote control to select

AUX IN mode.

Connecting the Speakers

Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each

speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the ter-

minal and insert the wire. Release the tab to lock wire in the terminal.

Note:

Center speaker provided with this unit is

magnetically shielded to protect your TV

set.

It is not recommended to place speak-

ers without magnetic shield near the TV

set.

Note:

When you press STOP, the unit stores the

point where playback was interrupted. If

you press

PLAY again, playback resumes

from this point.

To stop playback completely or to start

again from the beginning, press STOP twice.

If the unit is left in STOP mode for more than

5 minutes without any user interaction, a

screen saver is activated. At the end of 30

minutes without any user interaction, the

unit switches off automatically.

Note:

Insert 2 “AAA” batteries into the re-

mote control prior to use.

1. Left, Right (Front Speakers)

Front speakers carry primarily music and sound

effects.

2. Center

In surround mode, the center speaker carries most

of the dialog as well as music and effects.

It should be set between the left and right

speakers.

3. Surround (Rear Speakers)

The surround speakers’ overall sound balance

should be as close as possible to the front speakers.

Proper placement is vital to establish an evenly

distributed sound field.

4. Subwoofer

A subwoofer is designed to reproduce powerful

low

bass

effects

(explosions,

the

rumble

of

spaceships, etc.).

Courtesy Dolby Laboratories

Front Speaker Placement

For best results, follow the speaker placement

below.

Alignment

Align the center speaker evenly with (A) or slight-

ly behind (B) (the left and right speakers), but not

ahead of them.

Angle

Place the left and right speakers to form a 45-de-

gree angle with your favorite viewing position to

duplicate the soundtrack mixer’s perspective.

Height

The three front speakers should be as close as

possible to the same height. This often requires

placing the center speaker directly on top (A) or

beneath (B) the TV set.

Positioning Speakers

A

B

Note:

When connecting the speakers, make sure the polarities (“+” speaker wire to “+” on the re-

ceiver) of speaker wires and terminals match. For example, red wire to red terminal on the

receiver. If the cords are reversed, the sound will be distorted. Do not let the speaker wires

touch each other, it will damage the system’s amplifier.

Better Surround Placement

Location

If possible, place surround speakers to either side

of the listening area, not behind it.

Height

If space permits, install surround speakers 2-3 feet above

viewers. This helps to minimize localization effects.

Aiming

Aim surround speakers straight across the room,

not down at viewers, to help create a more open,

spacious surround sound field.

Alternative Surround Placement

Rear wall

If rear wall mounting is the only choice, aim the

speakers at each other (A), towards the front (B) or

towards the sidewalls (C, D).

Experiment with placement until sounds seem to

surround you, rather than come from behind you.

No adjacent walls

Surround speakers can go on stands facing

each other to approximate sidewall mounting

(A), or to the sides or rear of the viewing area,

aimed upwards; they can go right on the floor, or

preferably, a few feet off the floor such as on end

tables (B).

Test Tone/Channel Balance

Channel Balance

Your receiver is equipped with a test signal

generator to help balance the audio level for each

channel. See Audio Setup under The Setup Menu

section for more details on how to access this

feature.

Level Adjustment and Surround Channel Level

Expectation

Even though you adjust the surround channel to

be as loud as the others on the test signal, you

may find that surround channels seems quieter

for actual TV and Movie content. This is because

producers use surround for subtle atmospherics

and ambience, and only rarely for special effects.

RCR 192 AA8

OK

ON•OFF

:

Turn on/off the unit.

DVD/iPod

:

Switch between DVD and iPod mode.

TUNER

:

Select the TUNER and selects between FM/

AM.

AUDIO/AUX

:

Select and toggle between the Front AUDIO IN

mode and the Rear Auxiliary input (for listening

to audio input from connected TV, VCR or SAT/

Cable Box).

0-9

:

Number entry.

CLEAR

:

Quit the current setting manually from the TV

screen without saving change.

INFO

:

Access the Info menu.

OPTICAL:

Select digital audio input.

TITLE

:

Access the title menu of DVD discs.

DISC MENU

:

Access the disc menu during playback.

OK

:

Confirm your selection.

:

Navigate through the menus. The left and right

arrows also tune the radio frequency in the tuner

mode.

MUTE:

Mute and restore the sound.

SETUP:

Enter Setup menu.

RETURN:

In DVD mode, return to the previous menu.

VOL +/- :

Adjust the sound volume.

CH+/

, CH–/

:

Directly access the next or previous chapter

(DVD) or track (CD). Select programmed

stations in TUNER mode.

REV:

Start reverse accelerated play.

PLAY:

Start playing a disc.

FWD:

Start forward accelerated play.

SLOW:

Select SLOW motion function.

STOP:

Stop playback.

PAUSE:

Freeze frame, access frame advance.

AUDIO:

Access the audio function.

ANGLE:

Access the camera angle function for DVD disc.

ZOOM:

Access the Zoom function.

SUBTITLE:

Select the subtitle languages or turns subtitle

off ( if available).

HDMI:

Change video output signals (480p, 720p,

1080i or1080p).

SUBWOOFER:

Select among subwoofer output levels (soft/

balance/strong/powerful).

RANDOM:

Turn

on/off random playback on CDDA

disc.

REPEAT:

Access the repeat function.

LEVEL:

Toggle channels for different level settings.

Adjust the value using VOL +/-.

Compatible Discs

•

DVD

•

CD, CD-R, CD-RW

Compatible Formats

•

DVD, JPEG

•

CD

Regional Coding

Your unit has been designed to process regional

management information stored on DVD discs.

The regional code for your unit is 1. Discs that have

a different regional code will not play.

Operating the DVD Receiver

1. Turn on your television set.

2. Press ON•OFF on the remote control or ON/

STANDBY located on the unit’s front panel.

Press DVD on

the remote control.

Loading Disc

1. Press

on the front panel to open the disc

tray.

2. Place a disc onto the disc tray with the label

side up.

3. Press

again to close the disc tray.

Playback

Switch the unit and the TV set on.

1. After loading a disc, playback starts automatically,

or the disc menu appears. If the disc menu

appears, select the Play option to begin playback.

2. Press STOP to stop playback.

Accelerated Play

While the disc is playing, press REV or FWD one or

more times to vary the speed

and direction of the

accelerated play. Press PLAY

to resume normal

playback.

Pause

While the disc is playing, press PAUSE once for

freeze frame. Press PLAY to resume normal play-

back.

Frame Advance

1. Press PAUSE twice. “Step” is displayed.

2. Each time you press PAUSE button, the picture

advances one frame.

3. Press PLAY to resume normal playback.

Variable Slow Motion

1. Press SLOW button on the remote control in

play mode.

2. Each time the SLOW button is pressed the

speed of slow-motion playback changes in the

following sequence:

3. Press PLAY to resume normal playback.

Changing Chapter/Track

While the disc is playing, press the CH+/

, CH–/

button to go immediately to the next or previous

chapter, or to the next or previous track.

Zoom

1. While a disc is playing, press ZOOM until you

reach the zoom size you want. The ZOOM but-

ton toggles through X2, X3, X4 and then zooms

out

to X1/2, X1/3 and X1/4, then returns to nor-

mal playback.

2. Move from one area to another (pan) using the

arrow buttons.

3. To turn ZOOM off, press ZOOM until you get to

the Zoom Off option.

TT

CH

Note:

Invalid Key will be displayed if the func-

tion you select is not available.

The Info Menu

1. Press INFO on the remote control while a disc is

playing to display the info menu. The first banner

shows title, chapter, and time display information.

2. Press INFO again for audio language, subtitles,

and camera angle.

3. Press INFO a third time for play mode, bookmark

and sleep timer.

4. Use the right/left arrow buttons on the remote

control to select an icon.

5. Use the up/down arrow buttons to scroll

through the options.

7 cm

7 cm

10 cm

10 cm

10 cm

1

3

3

1

4

2

Subwoofer

Purple and

Black

Green and Black

Red and

Black

White and Black

Blue and Black

Gray and

Black

Rear Speakers

(Surround Sound)

Front Speakers

Right

Left

Center

Speaker

Insert

Right

Left

Press

Release

Digital Optical Input

Connect components capable of outputting

Dol-

by digital (e.g. TV or SAT/Cable Box) or standard

PCM (CD) format digital signals.

Use a fiber optical

cable for this digital audio connection. (cable not

included).

Press OPTICAL button on remote control or

SOURCE button on main unit to select OPTICAL IN

for digital audio output components.

-1-

-2-

-3-

-6-

-4-

-7-

-8-

-10-

-11-

-12-

-13-

]

Portable Cart

Warning


Accessories Provided

Things to Consider before You Connect

• Ensure that the mains supply in your house

complies with that indicated on the identification

sticker located on the back of your unit.

• Install your unit horizontally, away from

any source of heat (fireplace) or appliances

creating strong magnetic or electric fields. The

components of this unit are sensitive to heat.

The maximum ambient temperature should not

exceed 35°C / 95°F.

• Leave enough space around the unit to allow

adequate ventilation: 10 cm/4 inches on either side

and above the top, and 5 cm/2 inches at the rear.

• The humidity of the room should not exceed

75%. If you have to use the unit outdoors, do not

expose it to rain or splashing water. The apparatus

should not be exposed to dripping or splashing

and no objects filled with liquids, such as vases,

should be placed on the apparatus.

•

Moving the unit from a cold place to a warm one

can cause condensation on some components

inside the unit. Let the condensation disappear

on its own before turning the unit on again.

•

Before moving the unit, make sure the disc tray

is empty.

•

Where the mains plug or an appliance coupler

is used as a disconnect device, the disconnect

device shall remain readily operable.

Subwoofer

One Pig-Tail

antenna wire

Composite

video cable

One external AM

loop antenna

Remote control and 2

AAA batteries

OK

Left and right

front speakers

Center speaker

Left and right Sur-

round speakers

-5-

-9-

-14-


The Info Menu

Note: Many discs only have one title.

Note:

Time display function may not

be available on all discs.

Title/Chapter (DVD)/Track (Audio CD)

To directly access a title, chapter (DVD) or a track

(audio CD), press INFO, press OK.

Select the Title (TT), Track (TRK) or Chapter (CH)

icon and enter a number directly with the numeric

buttons. Press OK again to confirm.

Time Display

To access the Time Display, press INFO on the

remote control. Press the up/down arrow buttons

repeatedly to display:

DVD:

Chapter Time Elapsed, Chapter Time

Remain, Title Time Elapsed and Title

Time Remain.

Audio CD: Track Time Elapsed, Track time Remain,

Disc Time

Elapsed

and

Disc Time

Remain.

To directly access a location on the disc which

does not correspond to the start of a title or

chapter, press INFO once and press OK, highlight

the Time Display icon using the left/right arrow

buttons, then enter a time with the number

buttons (hh:mm:ss) and press OK.

Note:

Refer to the owner’s manual of the

connected

TV as well.

SEE MARKING ON BACK OF PRODUCT

TV

VIDEO IN

VIDEO IN

Y

P

P

B

R

Video

Cable

Component

Video Cable

(not supplied)

Green

Blue

Red

TV

HD

M

I

To HDMI

input

To HDMI

output

HDMI cable

(not supplied)

OR

OR

TV

SAT/

Cable Box

VCR

AUDIO OUT

Audio cable

Red

White

TV

OPTICAL

OU T

OR

SAT/

Cable Box

Select the input sources. Press repeatedly to

select:

• DVD/iPod – to access DVD/iPod mode.

• TUNER – to listen to the radio.

•

AUX (rear)/AUDIO IN (front) – to listen to the audio

input from the connected TV, VCR or SAT/Cable Box.

• OPTICAL (rear) - to connect to digital audio

components.

Start/pause

playing a disc

Toggles between different subwoofer

output levels (among soft/balance/

strong/powerful).

Adjust the

volume.

Switch the unit

on and off.

AUDIO IN jack -

to connect

portable audio

players.

iPod docking

compartment

Open and close

the disc tray.

Stop disc

playback.

X

1

/

2

S

F

1

/

3

1

/

4

S

F

1

/

5

S

F

1

/

7

S

F

1

/

6

X

S

F

X

X

X

X

Play

General Setup

Video

HDMI Setup

TV Type

Default

FM75

GND

White

Antenna

Note:

During picture slideshow, you can not

zoom out a picture unless HDMI Setup is

set to 480p.

Suggest using Ø3.5mm AUDIO IN jack for

MP3 player and AUX IN jacks for auxiliary

equipment such as DVD, VCR or PC.

DVD Info Display

CD Info Display

TT

C

H

Title

Track

Chapter

Time display

Time display

Audio language

Subtitles

Camera angle

Play mode

Play mode

Bookmark

Bookmark

Sleep timer

Sleep timer

1/10

1/16

00: 13: 07

1/3 En

D 5.1CH

Off

Off

TRK 1/10

00: 13: 07

Playmode

Bookmark

Sleep

Playmode

Bookmark

Sleep

STS8316Wi

English IB for RCA.indd

1

2009-07-15

14:55:05

RCA RTD316Wi RTD316Wi Product Manual

RCA RTD316Wi Manual

RCA RTD316Wi manual content summary: