Rane CP64S ZR1 / PR2 Remotes Data Sheet / Manual

DATA SHEET / MANUAL

ZR1 & PR2

COMMERCIAL PROCESSOR REMOTES

CP64S & CP52S CONNECTIONS

Turn the power to the CP unit OFF until all connections are made.

EUROBLOCK CONNECTIONS

When wiring to Euroblocks, a minimum wire gauge of 22 is pre-

ferred for reliability. If the ground or shield wire is left shorter,

it acts as a strain relief for the other wires. Cable with a flexible

jacket is easier to use and less likely to damage the connections.

Avoid stripping excess insulation. Inspect wires for nicks that

may lead to wire breakage. Fully insert each wire in the appropri-

ate socket and tighten the screw.

REMOTE INSTALLATION

°e CP64S supports wired remotes for Page Assign (PR2) and

Zone Level and Zone Source (ZR1) selection. °e CP52S only

supports Zone Level and Zone Source (ZR1) selection. Wire

lengths of up to 1000 feet are possible. A brief list of suitable

wire types is provided below in the section on Wire Types.

°e

PR2

remote provides Page Zone Assign for Page 1 and

Page 2 signals and is usually located at the Page source. If your

application requires one of the two PAGE ASSIGN switches to

control both Page 1 and Page 2 Assign, simply wire Page 1 and

Page 2 control bits in parallel. You may wish to leave the knob

off the unused control and cover it with one of the hole plugs

provided in the kit. If your installation requires Page 1 and Page

2 remote control at two different locations, only three wires are

required for each PR2 remote (Z1, Z2 & GND). As above, you

may wish to leave the knob off the unused control and cover it

with a hole plug.

°e

ZR1

remote provides Zone Level and Source Selection,

allowing local control from inside the zone. Two ZR1 remotes

may be used (use only one for each Zone). If only one of the two

controls is used, you may cover the unused control with one of

the hole plugs provided in the kit. If you require one ZR1 remote

to control both Zones, simply wire the ports in parallel. °is

may be done with selector only, volume only or both. If only one

of the two controls is wired in parallel, the other is still available

for a second remote.

When paralleling one remote across multiple CP64Ss, all

three control pins must be wired, including the shields.

Power to the CP64S or CP52S should be

off

until all connec-

tions are made. It is important to ensure that the Remote Ports

are not subjected to sustained voltages outside the range of 0 to

5 volts DC or high levels of static. Inputs are protected, howev-

er, caution is the better part of... you know. It is a good idea to

install the wiring, connect it to the remote assemblies and then

make the final connections at the CP unit. Do

not

short Vr1 or

Vr2 pins to ground. °ese pins

are

current limited, however, ex-

cess heat is generated in the 5 volt supply if a short occurs.

Never

subject the Vr1 or Vr2 pins to voltages above 5 volts.

REMOTE MOUNTING

°e ZR1 and PR2 remote assemblies mount in a standard U.S.

electrical box with a minimum depth of 2.25" (5.5 cm). Be sure

to note the wire color of each input in order to facilitate correct

wiring to the CP unit. Connect each wire to the 5-pin connec-

tor by fully inserting it in the correct socket and tightening the

screw. Make sure wires are free of nicks and that the cable jacket

is stripped back sufficiently to allow it to lie in the electrical box

with the remote assembly inserted. Use the flat head #6 screws

supplied with the kit to mount the remote assembly and silk-

screened front panel to the electrical box (see above diagram).

Note the “UP” arrow screened on the printed circuit board of

each remote (mount it pointing

up

).

Install each knob so that the line on the knob is properly

aligned with the silk-screening on the front panel of the remote

assembly. Install any Decora plate of your choice. For a secured

installation, you may wish to leave the knobs off and use a blank

Decora plate to cover the remote after adjustment.

PROGRAM SELECT

LEVEL

8

2

10

0

4

6

L1

L3

L2

P

PAGE 2 ASSIGN

PAGE 1 ASSIGN

BOTH

OFF

BOTH

Z1

OFF

Z2

Z1 Z2

Rane CP64S ZR1 / PR2 Remotes Data Sheet / Manual

Rane CP64S Manual

Rane CP64S manual content summary: