Rheem Warrior DVX Series User Guide

Instruction Sheet for Manufactured Home DV Co-Axial Kit

MANUFACTURED HOME FACTORY INSTALLATION

INSTRUCTIONS AND TRANSPORTATION SET-UP

Inspect shipment.

Inspect the contents of the kit for possible

damage. Verify the quantity of the components in the kit. The kit

includes: (A) 1- Co-Axial Roof Jack; (B) 3- Plastic Lock Ties;

(C) 1- Rain Cap; (D) 1- Co Axial Kit Instruction Sheet;

(E) 3- Warning Tag Labels and (F) 1- Carton Warning Label.

Please report any shortage to your local distributor or contact

1-800-432-8373 to get a replacement part. (See Figure 1)

The (3) “Warning Tag Labels” should be attached with the

plastic lock tie in the following locations:

(1) Gas Line Outside of Manufactured Home

(2) Master Shutoff Valve to Home

(3) Gas Valve on Water Heater

Locating Clearance Hole for Vent Cutout.

Cut a 7 ¼"

diameter hole in the ceiling and roof directly above the flue

of the water heater.

Placement of water heater.

Locate and install the water

heater following the instructions in the Use and Care

Manual, make certain the minimum clearances outlined in

the Use and Care Manual are observed.

Selecting the roof jack module.

The Co-axial vent roof

jack is divided into two modules . The lower module (See

Figure. 4) should be installed on the water heater at the fac-

tory location. The upper roof jack module (See Figure. 3)

should remain in the co-axial carton box and shipped inside

the manufactured home for assembly and setup at the per-

manent location of the home.

A

. Disassemble the upper

roof jack module by

expanding the "D" ring as

shown in Figure 3.

DO

NOT

remove the silicone

band attached to the 3"

pipe; it will be used for

final assembly at the per-

manent location of the

home.

B

. Install the rain cap on

the lower roof jack module

with the supplied "D" ring.

C

. Place the upper roof jack module back into the carton .

Seal the carton with the bright orange Carton Warning

Label (F) supplied. Make sure the carton box ships with the

manufactured home for final assembly of the vent system at

the permanent location of the home.

!

WARNING! THIS HOME HAS BEEN SHIPPED WITHAN INCOMPLETE WATER HEATER

VENTING SYSTEM FOR TRANSPORTATION USE ONLY. DO NOT CONNECT THE FUEL

SUPPLY TO THE HOME ORATTEMPT TO OPERATE THE WATER HEATER BEFORE

COMPLETION OF THE INSTALLATION OF THE UPPER ROOF JACK MODULE (ROOF JACK

CARTON STORED INSIDE HOME). FAILURE TO REMOVE TRANSPORTATION MODE RAIN

CAPAND TO INSTALL UPPER ROOF JACK MODULE MAY RESULT IN FIRE,

EXPLOSION OR ASPHYXIATION.

Figure 4 - Lower Roof Jack Module

Center Line of 7¼"

Diameter Hole in Roof

and Ceiling

Figure 2 -Vent Cutout

1

WARNING

INSTRUCTIONS

FOR KIT

IMPORTANT

THIS HOME HAS BEEN SHIPPED WITH

AN INCOMPLETE WATER HEATER VENTING

SYSTEM FOR TRANSPORTATION ONLY

CHECK ROOF OF HOME TO BE SURE THAT COMPLETE

FLUE ASSEMBLY HAS BEEN CORRECTLY INSTALLED

BEFORE ATTEMPTING TO OPERATE THE WATER HEATER.

(A) Co-Axial Roof Jack

(B) Plastic Lock Tie

(Qty. of 3)

(C) Rain Cap

(D) Co

Axial Kit

Instruction

Sheet

(E) Warning

Tag Labels

(F) Carton

Warning

Label

Figure 1-Kit Components

AP14417 (05/07)

Figure 3 -Upper Roof Jack Module

5" Outer Pipe

3" Inner Pipe

"D" Ring

Pull

Pull

Rheem Warrior DVX Series User Guide

Rheem Warrior DVX Series Manual

Rheem Warrior DVX Series manual content summary: