Ricoh Aficio MP 2500 Troubleshooting - Page 55

If the printing does not start, contact your service representative., Print, List/Test Print

Get Ricoh Aficio MP 2500 PDF manuals and user guides View all Ricoh Aficio MP 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

When You Cannot Print Problem Cause Solution Printing does not start. If the machine is operating in an extended wireless LAN, the receiver's MAC address may be preventing communication with the access point. Check access point settings when in infrastructure mode. Depending on the access point, client access may be limited by MAC address. Also, check there are no problems in transmission between access point and wired clients, and between access point and wireless clients. Printing does not start. The extended wireless LAN has Confirm the orange LED is lit, not started. and the green LED is lit or blinks during transmission. Printing does not start. Advanced encryption has been Check the settings of the Extended Se- 4 set using the Extended Security curity function with the administrator. function. Printing does not start. The login user name, password, or driver encryption key is invalid. Check the login user name, password, or driver encryption key is correct. The Data In indicator does not blink or light up. If the Data In indicator is unlit or • When the machine is connect- not flashing even after perform- ed to a computer via a cable, ing [Print], the machine has not re- check the computer print port ceived the data. settings are correct. • When it is networked with a computer, contact the administrator. The status indicator of the machine is red. The cause is displayed on the dis- Check the error message on the play of the control panel. display panel and take required action. See p.42 "When a Message Is Displayed". [List/Test Print] is disabled. A mechanical error might have occurred. Contact your service representative. See "List/Test Print", General Settings Guide. Printing does not start when using extended wireless LAN in Adhoc mode. Correct communication mode is not set. Turn the main power off and back on. See "Turning On the Power", About This Machine. Or, change the settings in [Network] under [Interface Settings] of [System Settings]. See "Network Settings", General Settings Guide. If the printing does not start, contact your service representative. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
When You Cannot Print
47
4
If the printing does not start, contact your service representative.
Printing does not start.
If the machine is operating in an
extended wireless LAN, the re-
ceiver's MAC address may be
preventing communication with
the access point.
Check access point settings when
in infrastructure mode. Depend-
ing on the access point, client ac-
cess may be limited by MAC
address.
Also, check there are no problems
in transmission between access
point and wired clients, and be-
tween access point and wireless
clients.
Printing does not start.
The extended wireless LAN has
not started.
Confirm the orange LED is lit,
and the green LED is lit or blinks
during transmission.
Printing does not start.
Advanced encryption has been
set using the Extended Security
function.
Check the settings of the Extended Se-
curity function with the administrator.
Printing does not start.
The login user name, password,
or driver encryption key is
invalid.
Check the login user name, pass-
word, or driver encryption key is
correct.
The Data In indicator
does not blink or light
up.
If the Data In indicator is unlit or
not flashing even after perform-
ing
[
Print
]
, the machine has not re-
ceived the data.
•
When the machine is connect-
ed to a computer via a cable,
check the computer print port
settings are correct.
•
When it is networked with a com-
puter, contact the administrator.
The status indicator of
the machine is red.
The cause is displayed on the dis-
play of the control panel.
Check the error message on the
display panel and take required
action. See p.42 “When a Message
Is Displayed”.
[
List/Test Print
]
is dis-
abled.
A mechanical error might have
occurred.
Contact your service representa-
tive. See “List/Test Print”, Gener-
al Settings Guide.
Printing does not start
when using extended
wireless LAN in Ad-
hoc mode.
Correct communication mode is
not set.
Turn the main power off and back
on. See “Turning On the Power”,
About This Machine.
Or, change the settings in
[
Net-
work
]
under
[
Interface Settings
]
of
[
System Settings
]
. See “Network
Settings”, General Settings
Guide.
Problem
Cause
Solution