Ricoh Aficio MP C305 Manuals - Page 179

Other messages, Printing was canceled by

Page 179 highlights

When Messages Are Displayed on the Control Panel Message "Exceeded the limit value for total data size of the selected files. Cannot select more files." Causes Solutions • The size of the selected file exceeds 1 GB. • The total size of the selected files exceeds 1 GB. Files or groups of files larger than 1 GB cannot be printed. • When the total size of the multiple files that are selected exceeds 1 GB, select files separately. • When the size of selected file exceeds 1 GB, print by using a function other than the Direct printing function from removable memory devices. You cannot select files of different formats at the same time. Other messages This section describes likely causes of and possible solutions for the error messages that are printed on the error logs or reports. Message "86: Error" "91: Error" "92: Error" "98: Error" Causes Solutions Parameters of the control code are invalid. Check the print settings. Printing was canceled by the Check that the data is valid. auto job cancel function due to a command error. Printing was canceled because [Job Reset] or the [Stop] key was selected on the machine's control panel. Perform the print operation again if necessary. The machine could not access the hard disk correctly. Turn off the main power switch, and then back on again. If the message appears frequently, contact your service representative. 177

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216

Message
Causes
Solutions
"Exceeded the limit value for
total data size of the
selected files. Cannot select
more files."
The size of the selected
file exceeds 1 GB.
The total size of the
selected files exceeds 1
GB.
Files or groups of files larger than 1 GB
cannot be printed.
When the total size of the multiple
files that are selected exceeds 1
GB, select files separately.
When the size of selected file
exceeds 1 GB, print by using a
function other than the Direct
printing function from removable
memory devices.
You cannot select files of different
formats at the same time.
Other messages
This section describes likely causes of and possible solutions for the error messages that are printed on
the error logs or reports.
Message
Causes
Solutions
"86: Error"
Parameters of the control
code are invalid.
Check the print settings.
"91: Error"
Printing was canceled by the
auto job cancel function due
to a command error.
Check that the data is valid.
"92: Error"
Printing was canceled
because [Job Reset] or the
[Stop] key was selected on
the machine's control panel.
Perform the print operation again if
necessary.
"98: Error"
The machine could not
access the hard disk
correctly.
Turn off the main power switch, and
then back on again. If the message
appears frequently, contact your
service representative.
When Messages Are Displayed on the Control Panel
177