Ricoh C811DN T2 Hardware Guide
Ricoh C811DN T2 - Aficio Color Laser Printer Manual
 |
UPC - 026649028205
View all Ricoh C811DN T2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ricoh C811DN T2 manual content summary:
- Ricoh C811DN T2 | Hardware Guide - Page 1
Operating Instructions Hardware Guide 1 Guide to the Printer 2 Installing Options 3 Connecting the Printer Cables 4 Configuration 5 Paper and Other Media 6 Replacing Consumables 7 Cleaning the Printer 8 Adjusting the Printer 9 Troubleshooting 10 Removing Misfed Paper 11 Appendix Read this manual - Ricoh C811DN T2 | Hardware Guide - Page 2
Trademarks Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. Inc. and any use of such marks by Ricoh Company, Ltd. is under license. Apple, AppleTalk, EtherTalk, Macintosh, Mac OS and True Type are trademarks of Apple - Ricoh C811DN T2 | Hardware Guide - Page 3
the IEEE 802.11b Interface Unit...46 Installing the Bluetooth Interface Unit...49 Installing the IEEE 1284 Interface Board...52 Installing the USB Host Interface Board...54 Installing a Camera Direct Print Card or Security Card 56 3. Connecting the Printer Cables Ethernet Cable Connection...59 - Ricoh C811DN T2 | Hardware Guide - Page 4
Media...86 Paper Not Supported by This Printer...95 Print Area...95 Loading Paper...97 Loading Paper into the Paper Tray, 500/1000-sheet Paper Feed Unit 97 Loading Paper into the 2000-sheet Paper Feed Unit 105 Loading Paper in the Bypass Tray...107 6. Replacing Consumables Replacing Toner...113 - Ricoh C811DN T2 | Hardware Guide - Page 5
the Waste Toner Bottle...132 Replacing the Fusing Unit and Transfer Roller 137 Replacing the Fusing Unit...137 Replacing the Transfer Roller...140 Adding Staples...142 When the Booklet Finisher is Installed...143 When the 2 Tray Finisher is Installed...147 7. Cleaning the Printer Cautions When - Ricoh C811DN T2 | Hardware Guide - Page 6
217 Paper Misfeed Message (Z)...218 Duplex Print Always Misfeeds...220 11. Appendix Moving and Transporting the Printer...223 Moving the Printer...223 Consumables...226 Toner...226 Photo Conductor Unit...227 Waste Toner Bottle...227 Staple Cartridge...227 Intermediate Transfer Unit...228 Fusing Unit - Ricoh C811DN T2 | Hardware Guide - Page 7
Positions of WARNING and CAUTION Labels This machine has labels for WARNING and CAUTION at the positions shown below. For safety, please follow the instructions and handle the machine as indicated. ATU082S 5 - Ricoh C811DN T2 | Hardware Guide - Page 8
ATU083S 6 - Ricoh C811DN T2 | Hardware Guide - Page 9
sure to read this. Quick Installation Guide Contains procedures for removing the printer from its box, connecting it to a computer, and installing its driver. Hardware Guide (this manual) Contains information about paper and procedures such as installing options, replacing consumables, responding to - Ricoh C811DN T2 | Hardware Guide - Page 10
when using the machine, and explanations of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure to read these warnings. Indicates supplementary explanations of the machine's functions, and instructions on resolving user errors. This symbol is located at the end of sections - Ricoh C811DN T2 | Hardware Guide - Page 11
the Specified Model In this manual, the following symbols indicate information that relates to a specific printer model. This indicates information about the 220 to 240 V model printer. Read if you have purchased this model. This indicates information about the 120 V model printer. Read if you have - Ricoh C811DN T2 | Hardware Guide - Page 12
. Select the appropriate version for your operating environment. • To uninstall the Operating Instructions, select [Programs] in the [Start] menu, select this printer driver, and then click [Uninstall]. You can uninstall each Manual separately. • If you are using an incompatible Web browser and the - Ricoh C811DN T2 | Hardware Guide - Page 13
details about the sizes and types of paper that can be used, see p.81 "Supported Paper for Each Tray". 5. Right Cover Open this cover to replace the fusing unit and transfer roller, or to remove jammed paper. 6. Handle Pull out this handle when lifting the printer. 7. Tray 1, Tray 2 in each tray. Up - Ricoh C811DN T2 | Hardware Guide - Page 14
when replacing the toner, photo conductor units or intermediate transfer unit. 11. Control Panel Contains keys for printer control and a display that shows printer status. 12. Paper Support Extend the paper support when printing to paper larger than A3 . • p.81 "Supported Paper for Each Tray - Ricoh C811DN T2 | Hardware Guide - Page 15
. Replace it with the intermediate transfer unit together. 5. Power Connector Connect the power cable to the printer. Insert the other end into an electrical outlet. 6. Drying Heater Switch If the paper in the paper tray is moist due to high humidity, the print quality may decrease. The drying - Ricoh C811DN T2 | Hardware Guide - Page 16
1. Guide to the Printer 8. USB Port Use a USB cable to connect the printer to a host computer. 1 14 - Ricoh C811DN T2 | Hardware Guide - Page 17
roller and the fusing unit together. 3. Inner Cover Open this cover when replacing the photo conductor unit or intermediate transfer unit. 4. Photo Conductor Unit From the left, the photo conductors are installed in the order of yellow (Y), cyan (C), magenta (M), and black (K). Replace the relevant - Ricoh C811DN T2 | Hardware Guide - Page 18
Guide to the Printer • "Replacement Alert/Replace IntTrans Unit soon." • "Replace IntTrans Unit." 6. Toner 1 From the left, the toner is installed in the order of black (K), yellow (Y), cyan (C), and magenta (M). Replace the relevant toner when the following messages appear: • " Out of toner - Ricoh C811DN T2 | Hardware Guide - Page 19
is receiving data from a computer. The Data In indicator lights up if there is data to be printed. 7. Alert Indicator Lights up when a printer error occurs. Follow the instructions that appear on the display. 8. Power Indicator Remains lit while the power is on. It is unlit when the power is off - Ricoh C811DN T2 | Hardware Guide - Page 20
1. Guide to the Printer 11. [Online] Key Indicates whether the printer is online or offline. Press this to switch between online and offline status. When the lamp is lit, the printer is online, enabling data reception from connected computers. 1 When the lamp is unlit, the printer is offline, - Ricoh C811DN T2 | Hardware Guide - Page 21
the status of options installed in the printer. 3. [Prt.Jobs] Press to display print jobs sent from a computer. 4. [Supplies] Press to display the menu of supplies for the printer. • Toner levels are displayed by default. To turn off the toner level display, select [Maintenance] [General Settings - Ricoh C811DN T2 | Hardware Guide - Page 22
Guide to the Printer Reading the Display and Using Keys 1 ATU051S 1. [Escape] key Cancels an operation or returns to the previous display. 2. Scroll keys Move the cursor in each direction. When the keys appear in this manual manual instructs you to "press [Option]", press the left selection key. 20 - Ricoh C811DN T2 | Hardware Guide - Page 23
interface unit IEEE 1284 Interface Board Type A IEEE 1284 interface board Camera Direct Print Card Type C Camera direct print card Data Overwrite Security Unit Type G Data overwrite security unit For installation of the options listed below, contact your sales or service representative - Ricoh C811DN T2 | Hardware Guide - Page 24
the 500-sheet paper feed unit to the 1000-sheet paper feed unit before attaching to the printer. 2. Attach the 1000/2000-sheet paper feed unit Either the 1000-sheet paper feed unit or 2000-sheet paper feed unit can be attached, but not both. 3. Attach the SDRAM module Install the expansion memory - Ricoh C811DN T2 | Hardware Guide - Page 25
sales or service representative. Installing Options Install options in the positions shown below. External options ATU086S 1. 500-sheet paper feed unit Attach to the underside of the printer. Up to 550 sheets of paper can be loaded, when using plain paper. The 500-sheet paper feed unit will be - Ricoh C811DN T2 | Hardware Guide - Page 26
punching. In addition, it also supports print job sorting features, such as shifting the output tray for each job. • *4: Finisher upper tray • *5: Finisher shift tray To attach this option, contact your sales or service representative. Paper feed unit and finisher combinations A finisher can - Ricoh C811DN T2 | Hardware Guide - Page 27
card p.56 "Installing a Camera Direct Print Card or Security Card" 2. USB host interface board p.54 "Installing the USB Host Interface Board" 3. Optional interface board • Gigabit Ethernet board p.43 "Installing the Gigabit Ethernet Board" • IEEE 802.11b interface unit p.46 "Installing the IEEE 802 - Ricoh C811DN T2 | Hardware Guide - Page 28
handle in the center of the board, push the board firmly into the printer. 2 • The following may occur if the controller board is not correctly installed: 1. All control panel indicators are lit. 2. No control panel indicators are lit. 3. The "SC670" error message appears on the display. ATU039S 26 - Ricoh C811DN T2 | Hardware Guide - Page 29
paper feed unit to the 1000sheet paper feed unit. Then, see p.30 "Attaching the Paper Feed Unit" for instructions about attaching this to the printer. 3. Printer 1000-sheet paper feed unit See p.30 "Attaching the Paper Feed Unit" for attachment instructions. 4. Printer 2000-sheet paper feed unit - Ricoh C811DN T2 | Hardware Guide - Page 30
. In this case, attach the 500-sheet paper feed unit to the 1000-sheet paper feed unit before attaching to the printer. This section explains how to attach the 500-sheet paper feed unit to the 1000-sheet paper feed unit. • The 500-sheet paper feed unit weighs approximately 13.5 kg (29.8 lb.). • When - Ricoh C811DN T2 | Hardware Guide - Page 31
straight down. Place it so that it is held firmly in place by the vertical pins. 2 ASZ183S 4. Pull the tray of the 500-sheet paper feed unit out slowly until it stops, then lift the front of the tray slightly, and pull it out completely. ASZ268S Place the tray on a flat surface - Ricoh C811DN T2 | Hardware Guide - Page 32
. • When using the 1000-sheet paper feed unit with the 500-sheet paper feed unit, attach the 500-sheet paper feed unit to the 1000-sheet paper feed unit before attaching to the printer. • When the 1000-sheet paper feed unit is attached, the 2000-sheet paper feed unit cannot be attached. • When the - Ricoh C811DN T2 | Hardware Guide - Page 33
in the printer driver. • Four or more people are required for installation. 1. Check the contents of the package. 2. Turn the printer off and unplug the power cable. 3. Remove the packaging from the paper feed unit. 4. When using the 1000-sheet paper feed unit with the 500-sheet paper feed unit - Ricoh C811DN T2 | Hardware Guide - Page 34
2. Installing Options 2 ASZ254S Return the handle you pulled out from the printer to its original position. 8. Pull tray 2 of the printer out slowly until it stops, then lift side of the tray opening to secure the printer to the paper feed unit. Tighten the screw firmly using a coin. 32 ASZ256S - Ricoh C811DN T2 | Hardware Guide - Page 35
• 1000-sheet paper feed unit: Twin Trays • 2000-sheet paper feed unit: LCT • If the tray was not installed properly, repeat the procedure from step 2. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • If the print area is not - Ricoh C811DN T2 | Hardware Guide - Page 36
2. Installing Options • p.167 "Adjusting Printing Position" 2 34 - Ricoh C811DN T2 | Hardware Guide - Page 37
with 256 MB of memory. This can be expanded to a maximum of 512 MB. • Before using the new memory unit, you must configure settings in the printer driver. 1. Turn the printer off and unplug the power cable. 2. Remove the five screws securing the controller board. ATU003S The removed screws will be - Ricoh C811DN T2 | Hardware Guide - Page 38
the SDRAM module in the indicated slot. ATU006S Two slots are provided for the SDRAM modules. The default 256 MB SDRAM module is installed in the inner slot. To install additional memory, insert the additional SDRAM module to the outer slot. 5. Align the notch on the SDRAM module with the slot - Ricoh C811DN T2 | Hardware Guide - Page 39
until it clicks into place. Attaching the SDRAM Module 2 ATU008S 7. When also installing the user account enhance unit, install it before returning the controller board to the printer. 8. Fit the controller board into the printer, and push it carefully in until it stops. ATU009S Push it firmly - Ricoh C811DN T2 | Hardware Guide - Page 40
procedure from step 1. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • Install the controller board carefully. See p.26 - Ricoh C811DN T2 | Hardware Guide - Page 41
the User Account Enhance Unit Installing the User Account Enhance Unit • Do not touch the inside of the controller board user account enhance unit. • Do not subject the user account enhance unit to physical shocks. 1. Check the contents of the package. AET080S 2. Turn the printer off and unplug - Ricoh C811DN T2 | Hardware Guide - Page 42
2. Installing Options 4. Holding the handle, carefully pull out the controller board. 2 ATU004S Using both hands, slide the controller board completely out and place it on a flat surface such as a table. ATU005S 5. Install the user account enhance unit as shown. 40 ATU011S - Ricoh C811DN T2 | Hardware Guide - Page 43
7. Press the user account enhance unit down until it clicks into place, and confirm that it is held securely. ATU013S 8. When also installing the SDRAM module, install it before returning the controller board to the printer. 9. Fit the controller board into the printer, and push it carefully in - Ricoh C811DN T2 | Hardware Guide - Page 44
representative. • Please help recycle by returning unneeded user account enhance units to your sales or service representative. • For information about printing the configuration page, see "Test Printing", Quick Installation Guide. • Install the controller board carefully. See p.26 "Cautions When Re - Ricoh C811DN T2 | Hardware Guide - Page 45
the Gigabit Ethernet Board Installing the Gigabit Ethernet Board • The printer's Ethernet and USB ports are not available when the Gigabit Ethernet board is attached to the printer. Use the Ethernet and USB ports on the Gigabit Ethernet board. • Before beginning work, ground yourself by touching - Ricoh C811DN T2 | Hardware Guide - Page 46
the controller board. 6. Tighten the two screws to secure the board. ATU018S • Confirm that the Gigabit Ethernet board was correctly installed by printing the configuration page. If it is correctly installed, "Gigabit Ethernet Board" will appear for "Device Connection" on the configuration page. 44 - Ricoh C811DN T2 | Hardware Guide - Page 47
even after reattempting installation, contact your sales or service representative. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • Before using the Gigabit Ethernet board, you must configure settings from the printer control panel. See - Ricoh C811DN T2 | Hardware Guide - Page 48
by touching something metal to discharge any static electricity. Static electricity can damage the unit. 2 • Do not subject the unit to physical shocks. 1. Check the contents of the package. ATU000S 2. Turn the printer off and unplug the power cable. 3. Loosen the two screws and remove the slot - Ricoh C811DN T2 | Hardware Guide - Page 49
4. Fully insert the interface unit. Installing the IEEE 802.11b Interface Unit 2 ATU017S Confirm that the interface unit is firmly connected to the controller board. 5. Tighten the two screws to secure the interface unit. ATU018S 6. Attach the antenna to the card. Attach them so that the label of - Ricoh C811DN T2 | Hardware Guide - Page 50
or service representative. • Before using the IEEE 802.11b interface unit, you must configure settings from the printer control panel. See p.76 "IEEE 802.11b (Wireless LAN) Configuration" for details. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide - Ricoh C811DN T2 | Hardware Guide - Page 51
the Bluetooth Interface Unit Installing the Bluetooth Interface Unit • When the Bluetooth interface unit is installed in the printer, Bluetooth-equipped devices such as computers and digital cameras can print wirelessly. • Before beginning work, ground yourself by touching something metal - Ricoh C811DN T2 | Hardware Guide - Page 52
2. Installing Options 4. Fully insert the interface unit. 2 ATU017S Confirm that the interface unit is firmly connected to the controller board. 5. Tighten the two screws to secure the interface unit. ATU018S 6. Attach the card to the card adapter. Attach them so that the label on both the card and - Ricoh C811DN T2 | Hardware Guide - Page 53
installation, contact your sales or service representative. • For details, see the operating instructions included with the Bluetooth interface unit. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • "Test Printing", Quick Installation Guide - Ricoh C811DN T2 | Hardware Guide - Page 54
2. Installing Options Installing the IEEE 1284 Interface Board • Before beginning work, a half pitch 36-pin interface cable. 1. Check the contents of the package. ATU022S 2. Turn the printer off and unplug the power cable. 3. Loosen the two screws and remove the slot cover. ATU023S The removed - Ricoh C811DN T2 | Hardware Guide - Page 55
If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • "Test Printing", Quick Installation Guide • p.66 "Parallel Cable Connection - Ricoh C811DN T2 | Hardware Guide - Page 56
Installing Options Installing the USB Host Interface Board • Connect the USB cable from a digital camera to the USB host interface board. • Connections between the USB host interface board and a computer are not supported cores to the cable. 2. Turn the printer off and unplug the power cable. 3. Loosen - Ricoh C811DN T2 | Hardware Guide - Page 57
If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • "Test Printing", Quick Installation Guide • p.63 "Digital Camera Connection - Ricoh C811DN T2 | Hardware Guide - Page 58
Options Installing a Camera Direct Print Card or Security Card 2 • Keep SD memory cards out of reach of children. If a child swallows a SD memory card, consult a doctor immediately. • Do not subject the card to physical shocks. 1. Check the contents of the package. AET104S 2. Turn the printer of - Ricoh C811DN T2 | Hardware Guide - Page 59
procedure from the beginning. If it cannot be installed correctly even after reattempting installation, contact your sales or service representative. • For information on printing the configuration page, see "Test Printing", Quick Installation Guide. • "Test Printing", Quick Installation Guide 57 - Ricoh C811DN T2 | Hardware Guide - Page 60
2. Installing Options 2 58 - Ricoh C811DN T2 | Hardware Guide - Page 61
Cables Ethernet Cable Connection Prepare a hub and other network devices, and connect the Ethernet cable to the printer. Connect 10BASE T or 100BASE TX cable to the printer's Ethernet port. For 1000BASE T, the optional Gigabit Ethernet board is available. 3 • An Ethernet cable is not supplied - Ricoh C811DN T2 | Hardware Guide - Page 62
1. Attach two ferrite cores to the Ethernet cable. Attach the core supplied with the printer to the connector end, and the one supplied with the Gigabit Ethernet board about 15 , see p.67 "Ethernet Configuration". • p.43 "Installing the Gigabit Ethernet Board". • p.67 "Ethernet Configuration". 60 - Ricoh C811DN T2 | Hardware Guide - Page 63
Reading the LED Lamps Standard Ethernet port Ethernet Cable Connection 3 ATU034S 1. Green: turns on when the printer is properly connected to the network. 2. Yellow: turns on when 100BASE-TX is in use. It turns off when 10BASE-T is in use. Optional Gigabit - Ricoh C811DN T2 | Hardware Guide - Page 64
Connect the opposite end's flat connector to the desired device such as your computer's USB interface, or a USB hub. The printer is now connected to the computer. The Plug and Play screen appears on the computer display. See "Installing the Printer Driver Using USB", Software Guide for details. 62 - Ricoh C811DN T2 | Hardware Guide - Page 65
USB Cable Connection • "Installing the Printer Driver Using USB", Software Guide • p.43 "Installing the Gigabit Ethernet Board" Digital Camera Connection This printer supports direct printing, which allows you to print images taken with a digital camera by connecting the camera directly to the - Ricoh C811DN T2 | Hardware Guide - Page 66
3. Connecting the Printer Cables 3 ATU038S • Not using the USB cable supplied with the USB host interface board camera. As shown below attach the hook where it will not interfere with printer operation and access. ATU045S • For the printing method, see "PictBirdge Printing", Software Guide. 64 - Ricoh C811DN T2 | Hardware Guide - Page 67
• p.54 "Installing the USB Host Interface Board" • p.56 "Installing a Camera Direct Print Card or Security Card" USB Cable Connection 3 65 - Ricoh C811DN T2 | Hardware Guide - Page 68
of the interface cable to your computer, and then secure the cable. The printer is now connected to the computer. Install the printer driver. See "Preparation for Printing", Software Guide for details. • "Preparation for Printing", Software Guide • p.52 "Installing the IEEE 1284 Interface Board" 66 - Ricoh C811DN T2 | Hardware Guide - Page 69
TCP/IP-capable environment. • Configure the printer for the network using the control panel. • The following table shows the control panel settings and their default values. These items appear in the all set automatically. • Configure these setting as necessary. See Software Guide for details. 67 - Ricoh C811DN T2 | Hardware Guide - Page 70
's IP address from changing. Before beginning, make sure that you know the IP address, subnet mask and gateway address that the printer will use. 1. Press the [Menu] key. 4 ATU050S 2. Press the [ ] or [ ] key to select [Host Interface], and then press the [OK] key. 3. Press the [ ] or [ ] to - Ricoh C811DN T2 | Hardware Guide - Page 71
key until the screen returns to the [Network] menu. 8. If you use IPv4, assign the IPv4 address to the printer. Press the [ ] or [ ] key to select [Machine IPv4 Address], and then press the [OK] key. To get Change the IP address from "011.022.033.044" to an IP address supported by your network. 69 - Ricoh C811DN T2 | Hardware Guide - Page 72
• For details about printing the configuration page, see "Test Printing", Quick Installation guide. Receiving an IP Address Automatically (DHCP) Follow this procedure to set the printer to receive an "IP address" automatically using "DHCP". The "DHCP" feature is active by default, so this procedure - Ricoh C811DN T2 | Hardware Guide - Page 73
press the [OK] key. The printer will automatically receive an IP address. Default Gateway 6. Press the [Menu] key to return to the initial screen. 7. Print a configuration page to confirm the settings. • For details about printing the configuration page, see "Test printing", Quick Installation Guide - Ricoh C811DN T2 | Hardware Guide - Page 74
as necessary. • Auto Select • Ethernet II • Ethernet 802.2 • Ethernet 802.3 • Ethernet SNAP 4 • Usually, you can use the default (Auto Select). When you first select [Auto Select,] the frame type detected by the printer is adopted. However, if your network can use more than two frame types, the - Ricoh C811DN T2 | Hardware Guide - Page 75
the settings. • For details about printing the configuration page, see "Test Printing", Quick Installation Guide. Setting the Ethernet Speed You can set the speed that the printer will use for Ethernet communications. In most cases, this should be left on the default setting, [Auto Select]. This - Ricoh C811DN T2 | Hardware Guide - Page 76
4. Configuration Router/HUB auto-negotiation (auto selection) [10Mbps Half [10Mbps Full D.] D.] - Printer [100Mbps Half D.] [100Mbps Full D.] [Auto Select] - • Connection cannot be established if the selected Ethernet speed does not match your network's trans- 4 mission speed. • The use - Ricoh C811DN T2 | Hardware Guide - Page 77
Press the [ ] or [ ] key to select the Ethernet speed, and then press the [OK] key. 4 6. Press the [Menu] key to return to the initial screen. 7. Print a configuration page to confirm the settings. • For details about printing the configuration page, see "Test Printing", Quick Installation Guide. 75 - Ricoh C811DN T2 | Hardware Guide - Page 78
LAN) Configuration Configure the printer to use IEEE 802.11b (Wireless LAN). The following table shows the control panel settings and their defaults. These items appear in the [Host Interface] menu. Setting Name Communication Mode 802.11 Ad hoc Default Channel 4 Communication Speed SSID - Ricoh C811DN T2 | Hardware Guide - Page 79
also be set using the Web Image Monitor. For details, see Web Image Monitor help, and "Configuring the Network Interface Board Using Web Browser", Software Guide. 6. If [802.11 Ad hoc] or [Ad hoc] is selected for [Communication Mode], confirm the channel to use for transmission. 7. Press the [ ] or - Ricoh C811DN T2 | Hardware Guide - Page 80
the configuration page, see "Test Printing", Quick Installation Guide. Setting the SSID When "Communication Mode" is set to "Infrastructure" or "802.11 Ad hoc", you must specify the Service 4 Set Identifier (SSID) of the wireless access point that the printer will connect to for network access - Ricoh C811DN T2 | Hardware Guide - Page 81
LAN) Configuration Setting a WEP Key If the wireless network uses WEP to encrypt transmitted data, the corresponding WEP key must be set to the printer to allow communications with other network devices. Ask the network administrator for the WEP key to use. 1. In the IEEE 802.11b menu, press - Ricoh C811DN T2 | Hardware Guide - Page 82
[Menu] key to return to the initial screen. 7. Print a configuration page to confirm the settings. 4 • The WEP key can also be set using a Web browser. For details, see the Web Image Monitor Help. • For details about printing the configuration page, see "Test Printing", Quick Installation Guide. 80 - Ricoh C811DN T2 | Hardware Guide - Page 83
feed direction when loading paper. The direction is determined for each paper size. • If you want to change the default setting, contact your sales or service representative. Tray 1 Each size is specified for the following models. A4 81/2 11(Letter) Tray 2, 500/1000-sheet Paper Feed Unit (Tray 3 to - Ricoh C811DN T2 | Hardware Guide - Page 84
, B5 JIS , A5 5 Paper sizes requiring manual setting The following sizes are supported, but they must be selected using the control panel. See p.99 "Loading paper not automatically detected by this printer ". The custom size must be selected using the control panel or the printer driver. See p.101 - Ricoh C811DN T2 | Hardware Guide - Page 85
2000-sheet Paper Feed Unit (Tray 3) Supported Paper for Each Tray A4 8 1/2 11(Letter) • The paper tray guides are fixed. However, you can switch the setting between A4 and 8 1/2 11 (Letter) . If you wish to use a paper size other than the default, contact your sales or service representative. - Ricoh C811DN T2 | Hardware Guide - Page 86
, 8 1/4 13 (Folio) , Com10 , Monarch , C6 , C5 , DL Env , 8K , 16K , Com10 , Monarch , C6 , C5 , DL Env , 8K , 16K A3 , B4 JIS , A4 JIS , A6 , Paper Weight and Capacity Tray Tray 1 Tray 2 500-sheet paper feed unit 1000-sheet paper feed unit 2000-sheet paper feed unit Bypass tray Supported paper - Ricoh C811DN T2 | Hardware Guide - Page 87
Supported Paper for Each Tray • Do not load the paper so that the top of the stack exceeds the under limit mark inside the tray. 5 85 - Ricoh C811DN T2 | Hardware Guide - Page 88
ink-jet printer paper because it may stick to the fusing unit and cause a paper misfeed. • Do not reuse paper that has already been printed onto by other printers. 5 • When printing on OHP transparencies that have a print side, load them on the 2000-sheet paper feed unit with the print side up - Ricoh C811DN T2 | Hardware Guide - Page 89
using the bypass tray, make sure paper is not stacked higher than the paper guides inside it. Supported When printing on the reverse side of plain paper that is already printed on, select [Paper Type:] [XXX] (XXX: Tray 1 to 5, Bypass Tray) [Plain:Dup.Back] using control panel or printer driver. 87 - Ricoh C811DN T2 | Hardware Guide - Page 90
and Other Media Thick paper Paper thickness Printer setup 5 Printer driver setup Supported paper feeding tray Duplex printing Additional cautions 106 to 253 g/m2 • [Thick Paper 1]: 106 to 169 g/m2 (28 to 45 lb.) • [Thick Paper 2]: 170 to 219 g/m2 (45 to 58 lb.) • [Thick Paper 3]: 220 to 253 - Ricoh C811DN T2 | Hardware Guide - Page 91
Thin paper Paper thickness Printer setup Printer driver setup Supported paper feeding tray Duplex printing OHP transparencies Printer setup Printer driver setup Supported paper feeding tray Paper capacity Duplex printing Additional cautions Paper Recommendations 52 to 59 g/m2 (14 to 16 lb.) Select - Ricoh C811DN T2 | Hardware Guide - Page 92
inside the tray. When using the bypass tray, make sure paper is not stacked higher than the paper guides inside it. Supported Default: [Letterhead 1] If the print quality needs to be improved, select [Maintenance] [General Settings] [Letterhead Setting] [Letterhead 1] to [Letterhead 3] to change the - Ricoh C811DN T2 | Hardware Guide - Page 93
Printer driver setup Supported paper feeding tray Paper Recommendations Select [Paper Input] [Paper Type: Bypass Tray] [Label Paper]. Select [Label Paper] in [PaperType]. Bypass tray • Make sure paper is not stacked higher than the paper guides inside the bypass tray. Not supported Default - Ricoh C811DN T2 | Hardware Guide - Page 94
paper Printer setup Printer driver setup Supported paper feeding tray Duplex printing Coated paper setup 92 stacked higher than the paper guides inside it. Supported Default: [Glossy Paper 1] If the print quality needs to be improved, select [Maintenance] [General Settings] [Glossy Paper Setting - Ricoh C811DN T2 | Hardware Guide - Page 95
Special paper Special paper standard Printer setup Printer driver setup Supported paper feeding tray Duplex printing Envelopes Printer setup Printer driver setup Supported paper feeding tray Paper Recommendations per 4]. High numbered settings allow thicker paper to be used, but are printed more - Ricoh C811DN T2 | Hardware Guide - Page 96
stacked higher than the paper guides inside the bypass tray. Not supported Default: [Envelope 1] If the print quality needs to be improved, select a paper type that is appropriate for the thickness of the envelope you are using. Select [Maintenance] [General Settings] [Envelope Setting] [Envelope - Ricoh C811DN T2 | Hardware Guide - Page 97
when using paper printed on by printers other than a laser printer (e.g. monochrome and color copiers, ink-jet printers, etc.) Refrain from printing on the side on 5 which nothing is printed. • Surface-processed paper (excluding specified paper) • Special paper, such as thermal paper and carbon - Ricoh C811DN T2 | Hardware Guide - Page 98
and Other Media Paper 5 ATU087S • While printing may be possible on the entire page depending on the settings of the printer driver or print conditions, the quality cannot be guaranteed for the 5.2 mm (0.21 inches) margin of the upper side, the 4.2 mm (0.17 inches) margins of the right and - Ricoh C811DN T2 | Hardware Guide - Page 99
than the upper limit mark inside the paper tray. Paper misfeeds might occur. • Do not mix different types of paper in the same paper tray. • During printing, do not open or close the printer covers or bypass tray, or pull out or push in the paper 5 tray. • The default of tray 1 is as follows - Ricoh C811DN T2 | Hardware Guide - Page 100
Unlock the side guides. ASZ247S You do not need to adjust the side guides when loading paper into tray 1. 3. Pinch the clip on the side guide ( ), and match the guides to the paper size ( ) 5 AMJ016S 4. Pinch the clips on the end guide ( ), and match the guide to the paper size ( ). 98 ZHXH760J - Ricoh C811DN T2 | Hardware Guide - Page 101
push the tray forcefully, the paper guides might move. • For details about types of paper supported by this printer, see p.81 "Supported Paper for Each Tray". Loading paper not automatically detected by this printer Set the paper size on the control panel to load paper whose size cannot be detected - Ricoh C811DN T2 | Hardware Guide - Page 102
Other Media 1. Press the [Menu] key. ATU050S 2. Press the [ ] or [ ] key to select [Paper Input], and then press the [OK] key. 5 3. Press the [ ] or [ ] key to select [Paper Size: Tray 2], and then press the [OK] key. 4. Select the paper size you want to set using the scroll keys, and then press the - Ricoh C811DN T2 | Hardware Guide - Page 103
panel if you have already configured settings using the printer driver. However, when printing with a printer driver other than the RPCS printer driver, you must configure the settings using the control panel. • The following is the range of paper sizes that can be loaded in each type of tray - Ricoh C811DN T2 | Hardware Guide - Page 104
and Other Media 1. Press the [Menu] key. ATU050S 2. Press the [ ] or [ ] key to select [Paper Input], and then press the [OK] key. 5 3. Press the [ ] or [ ] key to select [Paper Size: Tray 2], and then press the [OK] key. 4. Select [Custom Size] using the scroll keys, and then press the [OK] key - Ricoh C811DN T2 | Hardware Guide - Page 105
Press the [Online] key. The display returns to the initial screen. If you want to return the settings to [Auto Detect] after printing with the custom paper size, load paper into the paper tray, and follow this procedure. 8. Press the [Menu] key. 5 ATU050S 9. Press the [ ] or [ ] key to select - Ricoh C811DN T2 | Hardware Guide - Page 106
improve printer performance by selecting the optimum paper type for the tray. You can select from the following paper types: • Plain Paper, Recycled Paper, Special Paper 1, Special Paper 2, Special Paper 3, Color Paper, Letterhead, Preprinted Paper, Bond Paper, Cardstock, Thick Paper 1, Thick Paper - Ricoh C811DN T2 | Hardware Guide - Page 107
in the same paper tray. 5 • During printing, do not open or close the printer covers, bypass tray, or paper tray. • Make sure to align paper and push it neatly to both sides of the tray. If you do not, it can cause a paper misfeed. • The default paper size of the 2000-sheet paper feed unit is as - Ricoh C811DN T2 | Hardware Guide - Page 108
load the new paper into the right and left sides with the print side up. You can load up to 1000 sheets in each side. ASZ250S 3. Push the paper tray carefully into the printer until it stops. 5 • For details about types of paper supported by this printer, see p.81 "Supported Paper for Each Tray - Ricoh C811DN T2 | Hardware Guide - Page 109
in together. • Set the size and direction of the loaded paper on the control panel or with the printer driver. Make sure the settings do not conflict. Otherwise, the paper may jam or the print quality may be affected. • Load paper with the print side down and in the short-edge feed direction. 107 - Ricoh C811DN T2 | Hardware Guide - Page 110
Check the print in advance using the same type of paper. 1. Open the bypass tray. 5 ASZ089S 2. If you load paper longer than A4 , pull out the bypass tray extension. ASZ090S 3. Slide the side guides outward ( ), and then load paper with the print side down, flush against the printer. 108 ASZ091S - Ricoh C811DN T2 | Hardware Guide - Page 111
the side guides to fit the paper width. Loading Paper 5. Press the [Menu] key. ASZ092S 5 ATU050S 6. Press the [ ] or [ ] key to select [Paper Input], and then press the [OK] key. 7. Press the [ ] or [ ] key to select [Paper Size: Bypass], and then press the [OK] key. 8. Select the paper size - Ricoh C811DN T2 | Hardware Guide - Page 112
settings using the printer driver. However, when printing with a printer driver other than the RPCS printer driver, you must configure the settings using the control panel. • The printer cannot print to custom size paper from applications that do not support custom size paper. 1. Press the [Menu - Ricoh C811DN T2 | Hardware Guide - Page 113
. You can improve printer performance by selecting the optimum paper type for the tray. You can select from the following paper types: • Plain Paper, Recycled Paper, Special Paper 1, Special Paper 2, Special Paper 3, Color Paper, Letterhead, Preprinted Paper, Label Paper, Bond Paper, Cardstock, OHP - Ricoh C811DN T2 | Hardware Guide - Page 114
and Other Media • Be sure to select the appropriate paper type when you load labels, thick paper, envelopes, or OHP transparencies in the bypass tray. • The paper type selected using the printer driver overrides that selected using the control panel. 1. Press the [Menu] key. 5 ATU050S 2. Press the - Ricoh C811DN T2 | Hardware Guide - Page 115
of water. Consult a doctor if necessary. • Avoid getting toner on your clothes or skin when removing a paper jam or replacing toner. If your skin comes into contact with toner, wash the affected area thoroughly with soap and water. • If toner gets on your clothing, wash with cold water. Hot water - Ricoh C811DN T2 | Hardware Guide - Page 116
mode setting to Black and White using the printer driver. • If black toner runs out, you cannot print in black and white or color until the black toner is replaced. 1. Holding the left and right side grips, carefully open the front cover. ASZ056S From the left, the toner is installed in the order - Ricoh C811DN T2 | Hardware Guide - Page 117
Replacing Toner ASZ057S 2. Holding the toner of the color to replace, pull it out carefully. 6 ASZ058S Do not shake the removed toner. Any remaining toner may leak. Pull the toner out slowly and carefully to prevent leakage. Place the old toner on paper or some other material to avoid dirtying your - Ricoh C811DN T2 | Hardware Guide - Page 118
Replacing Consumables 5. With the label facing up, fully insert toner into place, keeping the container horizontal. ASZ071S Do not install and remove toner repeatedly. Doing so results in toner leak. 6. Carefully close the front cover. Wait until [ Loading toner] disappears from the display. 6 116 - Ricoh C811DN T2 | Hardware Guide - Page 119
damage the grip. • Place no objects on the front or inner cover. The following is the replacement procedure for the yellow photo conductor unit located in the left end. The same procedure applies to replacement of other photo conductor units. 1. Turn off the printer and unplug the power cable. 117 - Ricoh C811DN T2 | Hardware Guide - Page 120
carefully open the front cover. ASZ056S 3. Turn the two green levers counterclockwise. 6 ASZ252S 4. Pulling the handle, slowly open the inner cover. ASZ295S The photo conductor units are installed as shown. From the left, the units are attached in the order of yellow (Y), cyan (C), magenta (M), and - Ricoh C811DN T2 | Hardware Guide - Page 121
Replacing the Photo Conductor Unit ASZ259S 5. Pull out the ring pull handle of the photo conductor unit. 6 ASZ062S 6. Holding the handle, pull the photo conductor unit out until the green grip area is completely visible on the left side. ASZ063S 119 - Ricoh C811DN T2 | Hardware Guide - Page 122
pull out the photo conductor unit. ASZ064S 8. Take the new photo conductor unit out of the box. 6 ASZ065S For black, install one photo conductor unit; for color, install all three together. Exposure to light reduces photo conductor unit performance. Replace the unit as quickly as possible. 9. Remove - Ricoh C811DN T2 | Hardware Guide - Page 123
Photo Conductor Unit 10. Holding the green grip on the left and the handle on the front, carefully insert the front end into the space horizontally. ASZ066S Insert it horizontally as shown below. 6 ASZ288S 11. Pushing the front of the photo conductor unit, fully insert it into the printer. ASZ067S - Ricoh C811DN T2 | Hardware Guide - Page 124
tape. Malfunctions occur if you attempt to print while the tape is still attached. • The removed tape is dirty. Be careful not to let it touch your hands or clothes. 14. When replacing a color photo conductor unit, replace the other two color units together using the same procedure, before closing - Ricoh C811DN T2 | Hardware Guide - Page 125
levers clockwise to lock the cover. Replacing the Photo Conductor Unit ASZ296S 17. Carefully close the front cover. 18. Plug in the power cable, and then turn on the printer. [Calibrating ...] appears on the display, and the printer starts calibration. Wait until it stops. Calibration takes four - Ricoh C811DN T2 | Hardware Guide - Page 126
filter together. Replacing the Intermediate Transfer Unit • The inside of this printer becomes very hot. Do not touch parts labeled " " (indicating a hot surface). Touching these parts will result in burns. • If the intermediate transfer unit is not installed correctly, a message appears on - Ricoh C811DN T2 | Hardware Guide - Page 127
the Intermediate Transfer Unit and Dustproof Filter 2. Holding the left and right side grips, carefully open the front cover. ASZ056S 3. Turn the two green levers counterclockwise. 6 ASZ252S 4. Pulling the handle, slowly open the inner cover. ASZ295S The intermediate transfer unit is installed as - Ricoh C811DN T2 | Hardware Guide - Page 128
6. Replacing Consumables ATU059S 5. Push up the lever on the right side, and open the printer's right cover carefully. Opening the right cover is necessary for transfer unit replacement. 6 ATU060S 6. Turn the green lever located on the left side of the transfer unit counterclockwise. 126 ATU061S - Ricoh C811DN T2 | Hardware Guide - Page 129
Replacing the Intermediate Transfer Unit and Dustproof Filter 7. Holding the green grip in the center of the transfer unit, pull the unit out until the handles on the top surface become completely visible. ATU062S 8. Lift the handles on the top surface. 6 ATU063S 9. Holding the handles, slowly pull - Ricoh C811DN T2 | Hardware Guide - Page 130
6. Replacing Consumables 11. Lift the handles on the top surface. ATU065S 12. Slide the transfer unit along the guide rails into the printer until the upper handles touch the printer body. 6 ATU066S 13. Lower the handles, and then push the front of the transfer unit to fully insert it into the - Ricoh C811DN T2 | Hardware Guide - Page 131
the inner cover. 6 ATU092S 16. Turn the green levers clockwise. ATU095S 17. Carefully close the right cover. 18. Carefully close the front cover. • This completes intermediate transfer unit replacement. Now go to the next procedure and replace the dustproof filter. 129 - Ricoh C811DN T2 | Hardware Guide - Page 132
and glove from the box. 3. Put the glove on either hand. 4. Remove the filters with the gloved hand. Put the filters into the intermediate transfer unit's 6 box. ATU071S Handle the removed filters with care. Waving the filters will release toner. 5. Remove the glove. Put the glove into the - Ricoh C811DN T2 | Hardware Guide - Page 133
6. Attach the new filters. Replacing the Intermediate Transfer Unit and Dustproof Filter ATU072S 7. Slide the dustproof filter cover back to its original position. 6 ATU073S 8. Plug in the power cable and turn on the printer. 131 - Ricoh C811DN T2 | Hardware Guide - Page 134
on the display, the waste toner bottle should be replaced soon. Prepare a new waste toner bottle. • Waste toner bottles cannot be reused. • Purchasing and storing extra waste toner bottles is recommended. • Before removing the waste toner bottle from the printer, spread paper or some other material - Ricoh C811DN T2 | Hardware Guide - Page 135
2. Pull out [Tray 1] carefully until it stops. Replacing the Waste Toner Bottle ASZ112S 3. Open the left front cover slowly. 6 ASZ113S 4. Holding the green grip located under the front of the waste toner bottle, and pull it out until the handle on the top is completely visible. ASZ114S 133 - Ricoh C811DN T2 | Hardware Guide - Page 136
5. Holding the handle, carefully pull out the waste toner bottle horizontally. ASZ115S 6. Put the waste toner bottle into the supplied plastic bag to prevent toner from leaking out of the bottle. Then, seal the bag. 7. Take the new waste toner bottle out of the box. 6 8. Remove the tape - Ricoh C811DN T2 | Hardware Guide - Page 137
Bottle 9. Slowly pull the thick paper out of the waste toner bottle vertically. ASZ287S 10. Holding the handle on the top, insert the waste toner bottle into the printer carefully. 6 ASZ117S 11. When the waste toner bottle is inserted to the handle area, push the front side of the waste bottle - Ricoh C811DN T2 | Hardware Guide - Page 138
6. Replacing Consumables 12. Carefully close the left front cover. ASZ119S 13. Carefully push [Tray 1] into the printer until it stops. 14. Plug in the power cable and turn on the printer. 6 136 - Ricoh C811DN T2 | Hardware Guide - Page 139
Replacing the Fusing Unit and Transfer Roller Replace the fusing unit if any of the following messages appear on the display: Replace the transfer roller at the same time. Replacing the Fusing Unit 6 • The fusing unit becomes very hot. When installing a new fusing unit, turn off the printer and - Ricoh C811DN T2 | Hardware Guide - Page 140
6. Replacing Consumables 3. Holding the green levers on both sides, pull the fusing unit out. ATU075S 4. Lift and hold the green handles on both sides of the fusing unit, and then slowly pull up the fusing unit. 6 ATU076S 5. Take the new fusing unit out of the bag. 138 ATU078S - Ricoh C811DN T2 | Hardware Guide - Page 141
Replacing the Fusing Unit and Transfer Roller 6. Lift and hold the green handles on both sides of the fusing unit. ATU079S 7. Holding the fusing unit by the handles, place it on the rails of the printer as indicated. 6 ATU080S 8. Return the green handles to their original positions ( ). Then, - Ricoh C811DN T2 | Hardware Guide - Page 142
6. Replacing Consumables Replacing the Transfer Roller 1. The transfer roller is installed as shown below. ATU052S 2. Holding the green grips on both sides, pull up the transfer roller. 6 ATU053S 3. Holding the green grips, pull out the transfer roller from the printer. 140 ATU054S - Ricoh C811DN T2 | Hardware Guide - Page 143
roller out of the bag. Replacing the Fusing Unit and Transfer Roller ATU055S Hold the grips on both sides of the transfer roller. 5. Place the transfer roller into the grooves of the printer. 6 ATU056S 6. Secure the transfer roller by pushing the green grips on both sides until it locks into - Ricoh C811DN T2 | Hardware Guide - Page 144
6. Replacing Consumables Adding Staples • Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not. Add staples to the finisher if the following messages appear on the display: 6 • Be sure to - Ricoh C811DN T2 | Hardware Guide - Page 145
When the Booklet Finisher is Installed 1. Open the front cover of the finisher. ASZ271S 2. Holding the R7 lever, pull out the staple unit. 3. Raise the lever. ASZ186S ASZ187S Adding Staples 6 143 - Ricoh C811DN T2 | Hardware Guide - Page 146
6. Replacing Consumables 4. Holding the lever on the cartridge, pull the cartridge gently out of the staple unit. ASZ188S 5. Pushing both sides of the cartridge, pull out the upper unit. 6 ASZ220S 6. Take out the empty staple case. ASZ221S 144 - Ricoh C811DN T2 | Hardware Guide - Page 147
7. Push the new case into the cartridge until it clicks. Adding Staples ASZ222S 8. Lower the upper unit carefully. 6 ASZ223S 9. Pull the ribbon out of the staple case that you attached. The ribbon rolls around the staple case. Make sure to pull it out completely. ASZ224S 145 - Ricoh C811DN T2 | Hardware Guide - Page 148
6. Replacing Consumables 10. Holding the lever on the cartridge, push the cartridge gently into the staple unit until it clicks. ASZ225S 11. Push the lever down until it clicks. 6 ASZ226S 12. Return the staple unit to its original position. 13. Close the front cover of the finisher. • If you cannot - Ricoh C811DN T2 | Hardware Guide - Page 149
When the 2 Tray Finisher is Installed 1. Open the front cover of the finisher. Adding Staples ASZ272S 2. Holding the lever, pull out the staple unit. 6 ASZ227S 3. Hold and lift the lever on the cartridge and pull the cartridge gently out of the staple unit. ASZ229S 147 - Ricoh C811DN T2 | Hardware Guide - Page 150
6. Replacing Consumables 4. Pushing both sides of the cartridge, pull out the upper unit. ASZ234S 5. Take out the empty staple case. 6 ASZ235S 6. Push the new case into the cartridge until it clicks. ASZ236S 148 - Ricoh C811DN T2 | Hardware Guide - Page 151
case. Make sure to pull it out completely. 6 ASZ238S 9. Holding the lever on the cartridge, push the cartridge down gently into the staple unit until it clicks. ASZ229S 10. Return the staple unit to its original position. 11. Close the front cover of the finisher. • If you cannot pull out the upper - Ricoh C811DN T2 | Hardware Guide - Page 152
6. Replacing Consumables 6 150 - Ricoh C811DN T2 | Hardware Guide - Page 153
, explosion or loss of sight. If the machine has laser systems, there is a risk of serious eye damage. • When removing misfed paper, do not touch the fusing unit because it could be very hot. Clean the printer periodically to maintain fine printing. Dry wipe the exterior with a soft cloth. If dry - Ricoh C811DN T2 | Hardware Guide - Page 154
Do not use chemical cleaner or organic solvent such as thinner or benzine. • If misfeeds or multi-feeds of paper occur after cleaning the friction pad, contact your sales or service representative. Paper Tray, 500/1000-sheet Paper Feed Unit The same procedure is applied to clean the friction pads of - Ricoh C811DN T2 | Hardware Guide - Page 155
2000-sheet Paper Feed Unit 1. Carefully pull out the paper tray until it stops. Cleaning the Friction Pads ASZ277S 2. Holding the lever on the right side of the tray, pull the tray completely out. 7 ASZ278S 3. Remove the loaded paper. 4. Wipe the friction pad with a soft damp cloth. ASZ279S 153 - Ricoh C811DN T2 | Hardware Guide - Page 156
7. Cleaning the Printer 5. Reload the paper into the paper tray and push it gently into the printer until it stops. ASZ280S 7 154 - Ricoh C811DN T2 | Hardware Guide - Page 157
other than the standard types are used, specks of paper may stick around the registration roller, causing problems. Clean the registration roller if white dots appear on prints. • The inside of this printer becomes very hot. Do not touch parts labeled "v" (indicating a hot surface). Touching these - Ricoh C811DN T2 | Hardware Guide - Page 158
7. Cleaning the Printer 3. Clean the registration roller by applying a soft damp cloth while turning it. ASZ145S 4. Close the right cover. 5. Plug in the power cable and turn on the printer. 7 156 - Ricoh C811DN T2 | Hardware Guide - Page 159
if white lines appear on prints. • Do not forcefully insert the cleaning stick. It may scratch the inside of the printer. 1. Turn the printer off and unplug the power cable. 2. Holding the left and right handles, open the front cover. ASZ056S The cleaning stick is installed inside the front cover - Ricoh C811DN T2 | Hardware Guide - Page 160
7. Cleaning the Printer 4. There are four holes to insert the cleaning stick. ASZ139S 5. Place the cleaning stick back inside the front cover. 7 ASZ140S Clean all holes. faces down when you replace the stick. 7. Close the front cover carefully. 8. Plug in the power cable and turn on the printer. 158 - Ricoh C811DN T2 | Hardware Guide - Page 161
After moving the printer, printing on thick paper, or printing repeatedly for some time, color degradation may occur. By performing automatic color adjustment, you can restore optimum print quality. 1. Press the [Menu] key. ATU050S 2. Press the [ ] or [ ] key to select [Maintenance], and then press - Ricoh C811DN T2 | Hardware Guide - Page 162
8. Adjusting the Printer 5. Press the [OK] key. 6. The confirmation message appears. Press [OK]. Automatic adjustment begins. Automatic adjustment takes about 30 seconds. A confirm message appears when complete. 7. Press [Exit]. The display returns to the Color Registration screen. The display - Ricoh C811DN T2 | Hardware Guide - Page 163
. If you print the same file repeatedly or toner was recently replaced, changes may occur in color tones. In such cases, you can obtain optimal print results by correcting the color gradation. • Color gradation correction is not required under normal circumstances. • If a printer is not used - Ricoh C811DN T2 | Hardware Guide - Page 164
8. Adjusting the Printer 1. Press the [Menu] key. ATU050S 2. Press the [ ] or [ ] key to select [Maintenance], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Quality Maintenance], and then press the [OK] key. 8 4. Press the [ ] or [ ] key to select [Color Calibration], and then - Ricoh C811DN T2 | Hardware Guide - Page 165
[OK] key. 9. Press the [ ] or [ ] key to adjust the correction value for the selected color, and then press the [OK] key. 10. Press [Result] to check the result by printing the calibration sheet. 8 11. After printing, press [Yes] to save the settings. 12. After completing all settings, press the - Ricoh C811DN T2 | Hardware Guide - Page 166
. The currently set correction value is printed in red. 8 Reading the gradation correction sheet The printed gradation correction sheet is read as shown below. Comparing the gradation correction sheet and correction value of each color, K (black), M (magenta), and C (cyan)/Y (yellow) determine the - Ricoh C811DN T2 | Hardware Guide - Page 167
Used to adjust the color printed when only black toner is used. The currently set correction value is printed in red. 2. M (magenta) correction values Used to adjust the color printed when only magenta toner is used. The currently set correction value is printed in red. 3. C (cyan)/Y (yellow - Ricoh C811DN T2 | Hardware Guide - Page 168
8. Adjusting the Printer 2. Press the [ ] or [ ] key to select [Maintenance], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Color Calibration], and then press the [OK] key. 4. Press the [ ] or [ ] key to select [Reset Setting], and then press the [OK] key. A confirmation - Ricoh C811DN T2 | Hardware Guide - Page 169
to update the printing position. However, updating is useful in some cases when the optional paper feed unit is installed. 1. Press the [Menu] key. ATU050S 2. Press the [ ] or [ ] key to select [Maintenance], and then press the [OK] key. 8 3. Press the [ ] or [ ] key to select [Color Registration - Ricoh C811DN T2 | Hardware Guide - Page 170
8. Adjusting the Printer 6. Print the test sheet to preview the settings. Use this sheet to confirm the current print position. 7. Press the [Escape] key to return to the registration menu. 8. Press the [ ] or [ ] key to select [Adjustment], and then press the [OK] key. 8 9. Press - Ricoh C811DN T2 | Hardware Guide - Page 171
Adjusting Printing Position AAL708S ): Print Area ): Paper Feed Direction 11. Press the [OK] key to return to the Registration menu. 12. Print the test sheet to confirm the adjustment result. 13. Press the [Online] key. 8 The display returns to the initial screen. 169 - Ricoh C811DN T2 | Hardware Guide - Page 172
8. Adjusting the Printer 8 170 - Ricoh C811DN T2 | Hardware Guide - Page 173
message may appear for a few seconds. It means the printer is initializing, replenishing toner, or executing maintenance operations. Wait a while. Printing... The printer is printing. Wait a while. Ready This is the default ready message. The printer is ready for use. No action is required. 171 - Ricoh C811DN T2 | Hardware Guide - Page 174
124 "Replacing the Intermediate Transfer Unit and Dustproof Filter" for intermediate transfer unit installation. Waiting... The printer is waiting for the next data to print. Wait a while. Alert Messages (in alphabetical order) Cannot print Check the file you want to print is a supported file type - Ricoh C811DN T2 | Hardware Guide - Page 175
if it is installed properly or contact your sales/service representative. For details about installing the unit, see p.54 "Installing the USB Host Interface Board". • Confirm error details by printing the Error Log. For details, see "List/Test Print Menu", Software Guide. • "List/Test Print Menu - Ricoh C811DN T2 | Hardware Guide - Page 176
short beeps repeated five times. Printer alert. 9 Printer requires user attention. Paper may have jammed or toner may need replenishing. • Users cannot mute the printer's tone alerts. When the printer beeps to alert users of a paper jam or toner request, if the printer's covers are opened and - Ricoh C811DN T2 | Hardware Guide - Page 177
bypass tray. See p.97 "Loading Paper". Can you print a configuration page? If you cannot print a configuration page, it probably indicates a printer malfunction. Contact your sales or service representative. See "Test Printing", Quick Installation Guide. Is the interface cable connected securely - Ricoh C811DN T2 | Hardware Guide - Page 178
or remove obstructions. How is the signal strength when using Bluetooth ? Try the following: • Check the Bluetooth interface unit is installed properly. • Check there are no obstructions between computer, printer and other devices. • Change the location of the computer. • Change the location of the - Ricoh C811DN T2 | Hardware Guide - Page 179
. Next, on the [File] menu, click [Properties]. 3. Click the [Port] tab. 4. Check the [Print to the following port] box to confirm that the correct port is selected. Windows XP, Windows Server 2003 1. Access the [Printers and Faxes] folder from [Start]. 2. Click to highlight the icon of the - Ricoh C811DN T2 | Hardware Guide - Page 180
9. Troubleshooting Printing Problems Toner smears appear on the print side of the page. • The paper setting may not be correct. For example, although you are using thick paper, the setting for thick paper may not be set. • Check the paper settings. • Check the printer driver's paper settings. See - Ricoh C811DN T2 | Hardware Guide - Page 181
paper, or between the side guides and the paper in the paper tray. Make sure there are no gaps. See p.97 "Loading Paper". • The fusing unit is deteriorated or damaged. Replace the unit. See p.137 "Replacing the Fusing Unit and Transfer Roller". The back of the paper is printed on. • The paper - Ricoh C811DN T2 | Hardware Guide - Page 182
g/m2 (40 lb.) is loaded. Change the paper for printing. With Windows 95/98/Me, Windows 2000/XP, Windows Server 2003 or Windows NT 4.0, when doing aggregate prints or bound prints. • Check that the paper size and direction set in the [Menu] tab of the printer driver are the same as those set in the - Ricoh C811DN T2 | Hardware Guide - Page 183
If you cannot load paper of the correct size, use the reduction function to reduce the image, and then print. See the printer driver Help. The color of the printout is different from the color on the computer's display. • The colors made using color toner are different from colors displayed on the - Ricoh C811DN T2 | Hardware Guide - Page 184
:] setting in the printer driver's dialog box. See the printer driver Help. Images are printed at an angle • Confirm that the side guides of the paper tray are locked. If paper is not loaded correctly, it may be processed at an angle. A color is missing or partially blurred. • Paper is damp. Use - Ricoh C811DN T2 | Hardware Guide - Page 185
empty, replace the toner cartridge of the displayed color. See p.113 "Replacing Toner". • When the message "Replace PCU:Black." or "Replace PCU:Colour." appears, replace the photo conductor unit. See p.117 "Replacing the Photo Conductor Unit". • The paper is damp. Use paper that has been stored - Ricoh C811DN T2 | Hardware Guide - Page 186
Other Media". • Check the paper settings of the printer driver. See the printer driver Help. • The fusing unit is deteriorated or damaged. Replace the unit. See p.137 "Replacing the Fusing Unit and Transfer Roller". When printing on OHP transparencies, a color is missing or black or white dots are - Ricoh C811DN T2 | Hardware Guide - Page 187
or Windows NT 4.0, attached options are not detected. • The computer and printer are not in two-way communication. You must configure attached options in the printer properties. For details, see the printer driver Help. If the problem cannot be solved, contact your sales or service representative - Ricoh C811DN T2 | Hardware Guide - Page 188
persists, contact your sales or service representative. No e-mail is received when an Alert occurs, and after resolving an Alert. • Confirm [Notify by Email] is active in the [System] Menu on the Control Panel. See "System Menu", Software Guide. • Access the printer through the Web browser, log - Ricoh C811DN T2 | Hardware Guide - Page 189
can be blocked by obstructions. Move the printer or client computer if necessary. When you use a Bluetooth connection, print jobs are transmitted relatively slowly. • If the printer is still not operating satisfactorily, contact your sales or service representative. Con- sult with the store where - Ricoh C811DN T2 | Hardware Guide - Page 190
is replaced, the next five to seven sheets of paper will not be stapled until the finisher has adjusted the position of the staple sheet. When the Booklet Finisher is Installed 1. Open the front cover of the finisher. 9 ASZ271S 2. Holding the R7 lever, pull out the staple unit. 188 ASZ186S - Ricoh C811DN T2 | Hardware Guide - Page 191
3. Raise the lever. Removing Jammed Staples ASZ187S 4. Holding the lever on the cartridge, pull the cartridge gently out of the staple unit. ASZ188S 5. Raise the face plate of the cartridge. 9 ASZ200S 189 - Ricoh C811DN T2 | Hardware Guide - Page 192
9. Troubleshooting 6. Remove the jammed staples. ASZ201S 7. Push the face plate down until it clicks. ASZ202S 8. Holding the lever on the cartridge, push the cartridge gently into the staple unit until it clicks. 9 ASZ225S 190 - Ricoh C811DN T2 | Hardware Guide - Page 193
9. Push the lever down until it clicks. Removing Jammed Staples ASZ226S 10. Return the staple unit to its original position. 11. Close the front cover of the finisher. When the 2 Tray Finisher is Installed 1. Open the front cover of the finisher. 9 ASZ272S 2. Holding the lever, pull out the staple - Ricoh C811DN T2 | Hardware Guide - Page 194
9. Troubleshooting 3. Hold and lift the lever on the cartridge and pull the cartridge gently out of the staple unit. ASZ229S 4. Raise the face plate of the cartridge. ASZ230S 5. Remove the jammed staples. 9 ASZ231S 192 - Ricoh C811DN T2 | Hardware Guide - Page 195
6. Push the face plate down until it clicks. Removing Jammed Staples ASZ232S 7. Holding the lever on the cartridge, push the cartridge down gently into the staple unit until it clicks. ASZ229S 8. Return the staple unit to its original position. 9. Close the front cover of the finisher. 9 193 - Ricoh C811DN T2 | Hardware Guide - Page 196
9. Troubleshooting Removing Punch Waste "The punch hole receptacle is full." or "Empty the punch receptacle." message appears, remove punch waste from the finisher. When these messages appear on the display, you cannot use the punch function. When the Booklet Finisher is Installed 1. Open the front - Ricoh C811DN T2 | Hardware Guide - Page 197
Removing Punch Waste 4. Close the front cover of the finisher. • If you do not re-install the punch waste box in step 3, the message remains displayed. • If the message remains displayed, re-install the punch waste box. • The message might appear even when the punch waste box is not full. In this - Ricoh C811DN T2 | Hardware Guide - Page 198
9. Troubleshooting 2. Pull out the punch waste box carefully, and then remove punch waste. ASZ282S 3. Re-install the punch waste box. ASZ291S 4. Close the front cover of the finisher. 9 • If you do not re-install the punch waste box in step 3, the message remains displayed. • If the message - Ricoh C811DN T2 | Hardware Guide - Page 199
10. Removing Misfed Paper Removing Misfed Paper An error message appears if a paper misfeed occurs. The error message gives the location of the misfeed. Check the location and remove the paper. • The inside of this printer becomes very hot. Do not touch parts labeled " " (indicating a hot surface). - Ricoh C811DN T2 | Hardware Guide - Page 200
10. Removing Misfed Paper Paper Misfeed Message (A) The A "Open the part as shown and remove paper." error message appears when a paper misfeed occurs in the paper feed section. • The inside of this printer becomes very hot. Before removing paper around the fusing unit, wait until the temperature of - Ricoh C811DN T2 | Hardware Guide - Page 201
Paper Misfeed Message (A) 3. If the paper cannot be removed, open the bypass tray and pull it out slowly. ASZ122S 4. Remove the paper slowly from the bypass tray. ASZ123S 5. Carefully close the right cover. 6. Carefully close the bypass tray. 10 199 - Ricoh C811DN T2 | Hardware Guide - Page 202
10. Removing Misfed Paper Paper Misfeed Message (B) The B "Read instructions in Front Cover to remove." error message appears when a paper misfeed occurs in the paper feed section. • The inside of this printer becomes very hot. Before removing paper around the fusing unit, wait until the temperature - Ricoh C811DN T2 | Hardware Guide - Page 203
3. Remove misfed paper slowly. Paper Misfeed Message (B) ASZ125S 4. Carefully close the right cover. 10 201 - Ricoh C811DN T2 | Hardware Guide - Page 204
10. Removing Misfed Paper Paper Misfeed Message (C) The C "Read instructions in Front Cover to remove." error message appears when a paper misfeed occursin the paper feed section. • The inside of this printer becomes very hot. Before removing paper around the fusing unit, wait until the temperature - Ricoh C811DN T2 | Hardware Guide - Page 205
3. Remove misfed paper slowly. Paper Misfeed Message (C) ASZ126S 4. Holding the C1 levers, pull out the fusing unit. ASZ127S 5. Raise the C2 lever and remove the paper carefully. ASZ128S 10 203 - Ricoh C811DN T2 | Hardware Guide - Page 206
Misfed Paper 6. Push the fusing unit back into the printer carefully until it completely stops. ASZ298S 7. Remove the paper slowly from the output area of the printer. ATU094S 8. Carefully close the right cover. • If the message indicating paper misfeed does not disappear, pull the fusing unit out - Ricoh C811DN T2 | Hardware Guide - Page 207
(D) Paper Misfeed Message (D) The D "Read instructions in Front Cover to remove." error message appears when a paper misfeed occurs while paper is being fed. 1. Push up the lever on the right side, and open the printer's right cover carefully. ATU098S 2. Open the left cover of the bridge unit - Ricoh C811DN T2 | Hardware Guide - Page 208
10. Removing Misfed Paper 4. Close the left cover of the bridge unit. ASZ181S 5. If the paper could not be removed, open the right cover of the bridge unit. 6. Remove the paper. ASZ182S 10 ASZ176S 7. Close the right cover of the bridge unit. 8. Carefully close the right cover. 206 - Ricoh C811DN T2 | Hardware Guide - Page 209
Paper Misfeed Message (R) Paper Misfeed Message (R) The R "Open Finisher and remove the paper." error message appears when a paper misfeed occurs inside the finisher. When the Booklet Finisher is Installed When R1, R2, or R3 is displayed. 1. Open the top cover of the finisher. ASZ189S 2. Raise the - Ricoh C811DN T2 | Hardware Guide - Page 210
10. Removing Misfed Paper 4. If the paper could not be removed, open the front cover of the finisher. 5. Raise the R2 lever. ASZ271S ASZ191S 6. Turn the R3 knob counterclockwise to remove the paper. 10 ASZ192S 7. Return the R2 lever to its original position. 208 - Ricoh C811DN T2 | Hardware Guide - Page 211
Paper Misfeed Message (R) 8. If the paper could not be removed, open the left cover of the bridge unit, and then turn the R3 knob clockwise to remove the paper. ASZ193S 9. Close the left cover of the bridge unit and top cover of the finisher. When R4, R5, or R6 is displayed. 1. Open the front cover - Ricoh C811DN T2 | Hardware Guide - Page 212
and remove the paper. ASZ196S 7. Return the R6 lever to its original position. 8. Close the front cover of the finisher. 10 When R7, R8, R9, R10, or R11 is displayed. • Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap - Ricoh C811DN T2 | Hardware Guide - Page 213
1. Open the front cover of the finisher. Paper Misfeed Message (R) ASZ271S 2. Holding the R7 lever, pull out the staple unit. ASZ186S 3. Pull the R8 lever and remove the paper. ASZ195S 4. Return the R8 lever to its original position. 10 211 - Ricoh C811DN T2 | Hardware Guide - Page 214
10. Removing Misfed Paper 5. Turn the R9 lever clockwise. ASZ204S 6. Turn the R10 lever clockwise. ASZ205S 7. Push the R11 lever outward to remove the paper. 10 ASZ206S 8. Return the R11 lever and reinstall the staple unit in. 9. Close the front cover of the finisher. 212 - Ricoh C811DN T2 | Hardware Guide - Page 215
When the 2 Tray Finisher is Installed When R1, R2, R3, or R4 is displayed. 1. Open the front cover of the finisher. Paper Misfeed Message (R) ASZ272S 2. Turn the R1 lever counterclockwise. 3. Open the R3 lever. ASZ207S ASZ208S 10 213 - Ricoh C811DN T2 | Hardware Guide - Page 216
10. Removing Misfed Paper 4. Turn the R2 lever counterclockwise. ASZ209S 5. Open the left cover of the bridge unit and remove the paper. ASZ210S 6. If the paper cannot be removed, open the R3 lever and remove the paper. 10 ASZ211S 214 - Ricoh C811DN T2 | Hardware Guide - Page 217
7. Raise the R4 lever up and remove the paper. Paper Misfeed Message (R) ASZ212S 8. Return the R3 and R4 levers to their original positions. 9. Close the front cover of the finisher. When R5, R6, R7, or R8 - Ricoh C811DN T2 | Hardware Guide - Page 218
could not be removed, raise the R6 lever and remove the paper. ASZ214S 5. Return the R6 lever to its original position. 6. Open the R3 lever. 7. Lower the R7 lever and remove the paper. ASZ215S 8. Return the R3 and R7 levers to their original positions. 9. Close the front cover of the finisher. 10 - Ricoh C811DN T2 | Hardware Guide - Page 219
Paper Misfeed Message (Y) Paper Misfeed Message (Y) The Y "Open the part as shown and remove paper." error message appears when a paper misfeed occurs in the paper feed section of an optional paper feed unit. • When a paper misfeed (Y) occurs, the paper tray is locked and cannot be pulled out. Do - Ricoh C811DN T2 | Hardware Guide - Page 220
and remove paper." error message appears when a paper misfeed occurs inside the duplex unit. • The inside of this printer becomes very hot. Before removing paper around the fusing unit, wait until the temperature of the covers inside the fusing unit and duplex unit cool down. • When a paper misfeed - Ricoh C811DN T2 | Hardware Guide - Page 221
Paper Misfeed Message (Z) 3. Holding the Z knob, open the cover, and then remove the paper carefully. ASZ177S 4. Close the cover. 5. Carefully close the right cover. 6. Open the upper right cover. ASZ178S 7. Remove misfed paper slowly. ASZ240S 8. Close the upper right cover. 10 219 - Ricoh C811DN T2 | Hardware Guide - Page 222
10. Removing Misfed Paper Duplex Print Always Misfeeds • The inside of this printer becomes very hot. Before removing paper around the duplex units, wait until the covers inside the fusing unit and duplex unit cool down. 1. Push up the lever on the right side, and open the printer's right cover - Ricoh C811DN T2 | Hardware Guide - Page 223
Duplex Print Always Misfeeds 4. Using your finger, push the paper up in the direction of the arrow. ASZ275S 5. Remove the paper from the upper right cover area carefully. ASZ276S 6. Close the upper right cover. 7. Carefully close the right cover. 10 221 - Ricoh C811DN T2 | Hardware Guide - Page 224
10. Removing Misfed Paper 10 222 - Ricoh C811DN T2 | Hardware Guide - Page 225
after use, do not take out any of the toners, photo conductor units, nor waste toner bottle to prevent toner spill inside the machine. Repack the printer using its original packaging for transporting. • The printer weighs approximately 95 kg (209 lb.). • Be sure to disconnect all cables from the - Ricoh C811DN T2 | Hardware Guide - Page 226
For details, see the relevant sections in this manual. • At least four people are required to lift the printer. • Be sure to keep the printer horizontal while moving it. To prevent toner from being released, move the printer slowly. • If optional paper feed units are attached, remove them from the - Ricoh C811DN T2 | Hardware Guide - Page 227
Moving and Transporting the Printer • When finished, return the handles to their original position. 11 225 - Ricoh C811DN T2 | Hardware Guide - Page 228
, paper type and paper size used, contents of print images, and environmental conditions such as temperature and humidity. • Toner (consumable) is not covered by warranty. However, if there is a problem, contact the store where it was purchased. 11 • When you first use this printer, use the toner - Ricoh C811DN T2 | Hardware Guide - Page 229
Consumables Photo Conductor Unit Name Black Drum Unit SP C811 Color Drum Unit SP C811 Average printable number of pages *1 40,000 pages 40,000 pages *1 A4/Letter 5% test chart, 2 pages/job, printing in monochrome/color only. • The actual number of printable pages varies depending on the image - Ricoh C811DN T2 | Hardware Guide - Page 230
Refill cartridge Number of shots Refill 5,000 shots 3 Intermediate Transfer Unit Name Transfer Unit SP C811 Average printable number of pages*1 1,600,000 pages *1 A4/Letter 5% test chart, 2 pages/job, printing in monochrome/color only. • The actual number of printable pages varies depending - Ricoh C811DN T2 | Hardware Guide - Page 231
Mainframe Configuration: Desktop Print Process: Laser beam scanning and Electrophotographic printing Four-drums tandem method First Print Speed: Monochrome: 8 seconds or less (A4 , 81/2 11 (Letter) ) Color: 9 seconds or less (A4 , 81/2 11 (Letter) ) • If the printer has not been used - Ricoh C811DN T2 | Hardware Guide - Page 232
300 dpi 1 bit Printer Language: PJL, RPCS, PCL5c/XL, PS3/PDF Fonts: PCL 5c/6 Monotype Imaging 35 Intellifonts, 10 TrueType fonts, 13 International fonts, and 1 Bitmap font. PostScript 3, PDF 136 fonts (Type 2:24, Type 14:112) Paper Size: See p.81 "Paper and Other Media" Paper Weight: See p.81 - Ricoh C811DN T2 | Hardware Guide - Page 233
Printing: 66 db (A) or less Standby: 39 db (A) or less Dimensions (W D H): 670 670 640 mm (26.4 26.4 25.2 inches) Weight: Approximately 95 kg (209.5 lb.) Warm-up Time: Less than 60 seconds (23 °C, 73 °F) Paper Capacity: Standard Paper Options Tray Unit TK3000/Paper Feed Unit PB3000 Paper Size: A3 - Ricoh C811DN T2 | Hardware Guide - Page 234
11. Appendix Paper Feed Unit PB3000 Paper Capacity: Tray Unit TK3000 Paper Feed Unit PB3000 Weight: Tray Unit TK3000 Paper Feed Unit PB3000 Power Consumption: 50 W or less LCIT PB3010 Paper Size: 580 620 260 mm (22.9 24.4 10.3 inches) 550 sheets (80 g/m2, 20 lb.) 550 sheets 2 (80 g/m2, 20 lb.) 15 - Ricoh C811DN T2 | Hardware Guide - Page 235
JIS , A6 , 81/2 11 (Letter) , 51/2 81/2 , 71/4 101/2 (Executive) , 8 13 (F/GL) , 81/2 13 (Foolscap) , 11 81/4 13 (Folio) , 16K • 500 sheet for the following paper sizes (80g/m2, 20lb.): A3 , B4 JIS , 12 18 , 11 17 , 81/2 14 (Legal) , 8K Staple: • 2 to 9 sheets, 100 sets for the following - Ricoh C811DN T2 | Hardware Guide - Page 236
- 2 positions [Finisher Booklet Tray] Paper Size: A3 , B4 JIS , A4 , B5 JIS , 11 17 , 81/2 14 (Legal) , 81/2 11 (Letter) Stack Capacity: 11 • 2 to 5 sheets: 30 sets • 6 to 10 sheets: 15 sets Power Consumption: Approximately 60 W (power supplied from the main unit) Dimensions: 535 600 930 mm - Ricoh C811DN T2 | Hardware Guide - Page 237
, 11 17 , 81/2 14 (Legal) , 81/2 11 (Letter) , 51/2 81/2 , 71/4 10 1/2 (Executive) , 8 13 (F/GL) 13 (Folio) , Com10 , Monarch , C6 , C5 , DL Env , 8K , 81/2 , 16K 13 (Foolscap) , 81/4 Paper Weight: 52 to 256 g/m2 (14 to 68 lb.) Stack Capacity: No Staple: 11 • 3,000 sheets for the following - Ricoh C811DN T2 | Hardware Guide - Page 238
, 11 17 , 81/2 14 (Legal) , 8 13 (F/GL) , 81/2 13 (Foolscap) , 81/4 13 (Folio) , 8K • 15 to 30 sheets, 100 to 33 sets for the following paper sizes (80g/m2, 20lb.): A3 , B4 JIS , 11 17 , 8 1/2 14 (Legal) , 8 13 (F/GL) , 81/2 13 (Foolscap) , 81/4 13 (Folio) , 8K Staple Capacity: Without Mixed Size - Ricoh C811DN T2 | Hardware Guide - Page 239
-T) USB 2.0 To use USB 2.0, a USB computer port and cable that support USB 2.0 are required. Data Transmission Speed: Ethernet: 10 Mbps, 100 Mbps Cable Between Devices: Ethernet: 100 m USB: 5 m USB Host Interface Unit Type A Interface Connector: 11 USB 2.0 host interface A type Data Transmission - Ricoh C811DN T2 | Hardware Guide - Page 240
11. Appendix IEEE 802.11b Interface Unit Type H Transmission Specification: Based on IEEE 802.11 b (Wireless LAN) Protocol: IPv4, IPv6, IPX/SPX, AppleTalk • SmartDeviceMonitor and Web Image Monitor are supported. Data Transfer Speed: Selected automatically from the speeds below: 1 Mbps, 2 Mbps, 5.5 - Ricoh C811DN T2 | Hardware Guide - Page 241
Specifications Data Transfer Speed: Selected automatically from the speeds below: 1 Mbps, 2 Mbps, 5.5 Mbps, the environment. Transmission Mode: Ad hoc and infrastructure mode Bluetooth Interface Unit Type 3245 Supported Profiles: SPP (Serial Port Profile), HCRP (Hardcopy Cable Replacement Profile), - Ricoh C811DN T2 | Hardware Guide - Page 242
11. Appendix Punch Unit (Booklet Finisher SR3000) Paper size: 2 holes 2 and 3 holes type A3 , B4 JIS , A4 , B5 JIS , A5 , 11 17 , 81/2 14 (Legal) 11 (Letter) , 71/4 101/2 (Executive) , 8 13 (F/GL) , 81/2 13 (Foolscap) , 81/4 13 (Folio) , 8K , 16K Paper weight: 52 to 163 g/m2 (14 to 43 lb.) 240 - Ricoh C811DN T2 | Hardware Guide - Page 243
Punch Unit (Finisher SR3030) Paper size: 2 holes 3 holes 2 holes 4 holes 4 holes Paper weight: 52 to 163 g/m2 (14 to 43 lb.) Specifications 2 and 3 holes type A3 , B4 JIS , A4 , B5 JIS , A5 , 11 17 , 81/2 14 (Legal) , - Ricoh C811DN T2 | Hardware Guide - Page 244
11. Appendix 11 242 - Ricoh C811DN T2 | Hardware Guide - Page 245
board 59 Gigabit Ethernet Board 43 Glossy Paper 91 Guide to the Printer 11, 13, 15, 17 I IEE 1284 Interface Board 66 IEEE 284 Interface Board 52 IEEE 802.11b Interface Unit 23, 46 Inner Cover 15 Installing Options 21, 23 Interior 15 Intermediate Transfer Unit 15, 228 IP Address 67 J Job - Ricoh C811DN T2 | Hardware Guide - Page 246
Lamps 61 Rear View 13 Removing Jammed Staples 188 Removing Misfed Paper 197 Removing Punch Waste 194 Replace the Fusing Unit and Transfer Roller.....137 Replacing Consumables Replacing Toner 113 Replacing the Intermediate Transfer Unit and Dustproof Filter 124 Replacing the Photo Conductor - Ricoh C811DN T2 | Hardware Guide - Page 247
T the Gigabit Ethernet Board 62 Thick Paper 88 Thin Paper 89 Toner 16 Transfer Roller 15 Transfer Unit 15 Tray 1 11, 97 Tray 2 11, 97 Tray 3 97, 105 Tray 4 97 Tray 5 97 Tray Unit TK3000 231 Troubleshooting 171 Types of Paper and Other Media 86 U Upper Right Cover 11 USB Cable - Ricoh C811DN T2 | Hardware Guide - Page 248
MEMO 246 - Ricoh C811DN T2 | Hardware Guide - Page 249
MEMO 247 - Ricoh C811DN T2 | Hardware Guide - Page 250
MEMO 248 GB GB EN USA G133-8612 - Ricoh C811DN T2 | Hardware Guide - Page 251
Copyright © 2006 - Ricoh C811DN T2 | Hardware Guide - Page 252
Hardware Guide Model No. CLP240D/C7640nD/LP440c/Aficio SP C811DN EN USA G133-8614
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
 |
 |
10
8
9
11
Guide to the Printer
Installing Options
Connecting the Printer Cables
Configuration
Paper and Other Media
Replacing Consumables
Cleaning the Printer
Adjusting the Printer
Troubleshooting
Removing Misfed Paper
Appendix
1
2
3
4
5
6
7
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information
before using the machine.
Hardware Guide
Operating Instructions