Rocketfish RF-MONO70C Quick Setup Guide (English)
Rocketfish RF-MONO70C Manual
 |
View all Rocketfish RF-MONO70C manuals
Add to My Manuals
Save this manual to your list of manuals |
Rocketfish RF-MONO70C manual content summary:
- Rocketfish RF-MONO70C | Quick Setup Guide (English) - Page 1
RF-MONO70C I 70" Carbon Fiber Monopod Quick Setup Guide Package contents • Monopod with pan head • Mounting plate Note: mounting plate is on the pan head. • Wrench (1) • Quick Setup Guide Important safety instructions • Make sure that all levers, handles, knobs, and leg locks are correctly tightened
-
1
 |
 |
RF-MONO70C
I
70" Carbon Fiber Monopod
Quick Setup Guide
#
Component
Description
1
Quick-release mounting plate
Mount your device to this removable plate.
2
1/4" screw
Tighten to secure your device to the mounting plate.
3
Mounting base plate
Clamp the quick-release mounting plate to this base plate.
4
Variable angle head ball
Allows the head to be adjusted to any angle.
5
Safety lock pin
Prevents the mounting plate from falling out when the quick
release clamp knob is released.
6
Pan locking knob
Locks the horizontal movement of the head.
7
Quick-release plate locking knob
Locks the quick-release mounting plate to the tripod.
8
Head ball locking knob
Sets the head at different angle. Loosen to permit movement
of the head ball. Tighten to stop movement of the head ball.
Package contents
•
Monopod with pan head
•
Mounting plate
Note
: mounting plate is on the pan head.
•
Wrench (1)
•
Quick Setup Guide
Important safety instructions
•
Make sure that all levers, handles, knobs, and leg locks are correctly
tightened before use.
•
Do not carry or transport the monopod with camera equipment attached
(for example, over your shoulder or cradled in your arms).
•
Do not store or expose your monopod to excessive heat or cold, or use near
any flame or fire.
•
Do not oil or grease any part of the monopod.
•
Do not use any solvents or thinners to clean your monopod.
Use only a mild detergent and wipe dry with only a soft, lint-free cloth.
•
Do not exceed the load limit of this product. (See Specifications)
Features
Using your monopod
To set up your monopod:
1
Unscrew the leg locks and extend the leg to the desired
length.
2
Tighten the leg locks to adjust the monopod to the desired
height.
Caution
: Incorrectly securing a leg lock can cause the
monopod leg to retract unexpectedly and could result in
damage to the monopod or to the attached camera or
camcorder.
3
To remove the mounting plate, unscrew the quick-release
plate locking knob, then press the safety lock pin and lift the
plate away from the head.
4
Secure your camera or camcorder to the mounting plate
with the 1/4" screw on the bottom of the plate. Tighten the
screw firmly to avoid unintended lateral movement of your
device.
Specifications
One-year limited warranty
Visit www.rocketfishproducts.com for details.
Contact Rocketfish:
For customer service please call 1-800-620-2790
www.rocketfishproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN 55423-3645 USA
© 2010 BBY Solutions, Inc., All Rights Reserved. ROCKETFISH is a trademark of BBY
Solutions, Inc. All other products and brand names are trademarks of their
respective owners.
ENGLISH 10-0540
Minimum
Maximum
Maximum
Maximum
Folded
operating
operating
tube
Net
load
Model
height
height
height
diameter
weight
capacity
RF-MONO70C
22.8 in
22.8 in
70 in
1.14 in
1.82 lbs.
20 lbs.
(579 mm)
(579 mm)
(1778 mm)
(29 mm)
(820 g)
(9 kg)