Ryobi A18MS01 English Manual
Ryobi A18MS01 Manual
 |
View all Ryobi A18MS01 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ryobi A18MS01 manual content summary:
- Ryobi A18MS01 | English Manual - Page 1
OPERATOR'S MANUAL MITER SAW STAND A18MS01 Your miter saw stand has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of - Ryobi A18MS01 | English Manual - Page 2
Do not apply an unbalanced load that could cause the miter saw stand to tip over. Save these instructions. Refer to them frequently and use them to instruct others who may use this accessory. If you loan someone this accessory, loan them these instructions also to prevent misuse of the product and - Ryobi A18MS01 | English Manual - Page 3
minute Wet Conditions Alert Do not expose to rain or use in damp locations. Read The Operator's Manual To reduce the risk of injury, user must read and understand operator's manual before using this product. Eye Protection Always wear safety goggles, safety glasses with side shields, or a full - Ryobi A18MS01 | English Manual - Page 4
minor or moderate injury. (Without Safety Alert Symbol) Indicates a situation that may result in property damage. work stop FEATURES saw mounting bracket work support work support mounting bracket work stop work support extension rail work support mounting bracket extension rail Fig. 1 4 - Ryobi A18MS01 | English Manual - Page 5
parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: Do not attempt to modify this tool or create accessories serious personal injury. PACKING LIST Miter Saw Stand Saw Mounting Brackets (2) Work Supports (2) Work Support Mounting Brackets (2) Work Stops (2) - Ryobi A18MS01 | English Manual - Page 6
sure bolts do not extend above the table of the miter saw. If the saw has holes that line up with the slots in the saw mounting brackets: HEIGHT ADJUSTMENT KNOB WORK SUPPORT mounting bracket Fig. 4 n Unplug the saw and lock the saw arm in the down position. n Place a 2 x 4 or similar type of - Ryobi A18MS01 | English Manual - Page 7
nuts (not included). n Drill holes in the mounting surface to match the slots in the saw mounting brackets. n Proceed with installation as previously described. NUT LOCK WASHER flat WASHER NUT LOCK WASHER flat WASHER SAW MOUNTING BRACKET MITER SAW SLOT MOUNTING SURFACE CARRIAGE BOLT 7 Fig. 7 - Ryobi A18MS01 | English Manual - Page 8
ASSEMBLY MOUNTING THE MITER SAW TO THE STAND See Figures 8 - 9. n Lift the saw and bracket assembly, allowing the assembly to tilt slightly toward your body. n While still tilted toward you, hook the front edge of the bracket assembly onto the front rail of the stand. WARNING: To avoid serious - Ryobi A18MS01 | English Manual - Page 9
secure to stand Fig. 9 accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the following purpose: To provide a stable, secure work surface for a miter saw - Ryobi A18MS01 | English Manual - Page 10
building and installing an optional workshelf See Figures 12 - 14. Use the following directions, if desired, to build a workshelf for the miter stand. Materials needed: n 9 x 20 in. plywood, 3/4 in. thick n 8 wood screws, 1-1/4 in. length n Drill and bit to drill and countersink screw holes Building - Ryobi A18MS01 | English Manual - Page 11
the 3-1/2 x 9 in. plywood and insert shelf between top and bottom rails of miter stand until edge of vertical 6" strips touch miter stand front rail. n Place the 3-1/2 x 9 in. plywood between the front and back rails of the miter stand. Re-align the pre-drilled holes in the top piece with the - Ryobi A18MS01 | English Manual - Page 12
the bracket on the miter stand rails and bracket adjustment screws. nut BRACKET ADJUSTMENT SCREW screwdriver Fig. 15 To purchase additional saw mounting bracket assemblies (part no. A000220601), call Ryobi customer service at 1-800-525-2579. 983000-710 9-24-08 (REV:02) ONE WORLD TECHNOLOGIES
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
OPERATOR’S MANUAL
MITER SAW STAND
A18MS01
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your miter saw stand has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for buying a Ryobi product.