Ryobi AC04016 Operation Manual
Ryobi AC04016 Manual
 |
View all Ryobi AC04016 manuals
Add to My Manuals
Save this manual to your list of manuals |
Ryobi AC04016 manual content summary:
- Ryobi AC04016 | Operation Manual - Page 1
, user must read and understand the operator's manual for their lawn mower and this instruction sheet. Always wear eye protection with side shields performing any of the functions described in these instructions, take your unit to a qualified service center. WARNING: Always protect hands by wearing - Ryobi AC04016 | Operation Manual - Page 2
autre des tâches décrites dans les présentes instructions, confiez l'unité à un centre de ré el usuario debe leer y entender el manual del operador para su podadora y esta Si está asentada correctamente, la hoja permanecerá plana contra el support du hoja. Vuelva a instalar el perno de la hoja
-
1 -
2
 |
 |
E
C
LAWN MOWER BLADE
AC04016
For use with RYOBI
®
16 in.
Electric Lawn Mower ONLY
995000303
8-3-17 (REV:01)
WARNING!
To reduce the risk of injury, user must
read and understand the operator’s
manual for their lawn mower and this
instruction sheet. Always wear eye
protection with side shields marked
to comply with ANSI Z87.1. Ensure
compatibility and fit before using this
accessory. Do not use this accessory
if a part is damaged or missing. If you
are not comfortable performing any
of the functions described in these
instructions, take your unit to a quali-
fied service center.
WARNING:
Always protect hands by wearing
heavy gloves and/or wrapping the
cutting edges of the blade with rags
and other material when performing
blade maintenance. Contact with the
blade could result in serious personal
injury.
REPLACING THE CUTTING
BLADE
See Figures 1 - 2.
Stop the motor. Allow blade to come
to a complete stop.
Disconnect the power supply.
Turn the mower on its side.
Wedge a block of wood between the
blade and mower deck to prevent the
blade from turning.
Fig. 1
Loosen the blade bolt by turning it
counterclockwise (as viewed from
bottom of mower) using a 20 mm
wrench or socket (not provided).
Remove the blade bolt and blade.
Install the new blade. Ensure blade
is properly seated with the two blade
posts inserted into the holes on the
blade. Make sure it is installed with
the curved ends pointing up toward
the mower deck and not down
toward the ground. When seated
properly, the blade should be flat
against the blade mount.
Reinstall the blade bolt and finger
tighten.
NOTE:
Make certain all parts are
replaced in the exact order in which
they were removed.
Torque the blade bolt down clock-
wise using a torque wrench (not pro-
vided) to ensure the bolt is properly
tightened. The recommended torque
for the blade bolt is 350 – 400 in. lbs.
WARNING:
Ensure blade is properly seated and
the blade bolt is tightened to the
torque specifications above. Failure
to properly attach the blade could
cause it to come loose or detach and
result in possible serious personal
injury.
TECHTRONIC INDUSTRIES POWER EQUIPMENT
1428 Pearman Dairy Road
Anderson, SC 29625 USA
1-800-860-4050
www.ryobitools.com
Fig. 2
A - Blade (lame, hoja)
B - Wrench (clé, llave)
C - Block of wood (pièce de bois, bloque de
madera)
A
C
B
A
B
D
A - Blade (lame, hoja)
B - Blade bolt (boulon de lame, perno de la hoja)
C - Blade post (half circle) [tige pour lame (demi-
cercle), poste de la hoja (semicircular)]
D - Bolt hole (round) [trou pour boulon (ronde),
orificio de el perno (redondo)]
E - Post hole (half circle) [trou pour tige (demi-
cercle), orificio del poste (semi-circular)]
E
C