Ryobi DP102L English Manual
Ryobi DP102L Manual
 |
View all Ryobi DP102L manuals
Add to My Manuals
Save this manual to your list of manuals |
Ryobi DP102L manual content summary:
- Ryobi DP102L | English Manual - Page 1
MANUAL 10 in. DRILL PRESS DP102l Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user - Ryobi DP102L | English Manual - Page 2
...3-4 Specific Safety Rules...5 Symbols...6-7 Electrical...8 Glossary of Terms...9 Features...10-11 Tools Needed...11 Loose Parts...12 Assembly...13-17 Operation...18-20 Adjustments...21-22 Maintenance...23 Troubleshooting...24 Parts Ordering / Service...Back - Ryobi DP102L | English Manual - Page 3
all instructions listed below, may result in electric shock, fire and/or serious personal injury. READ ALL INSTRUCTIONS KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the applications and limitations as well as the specific potential hazards related to this tool. GUARD AGAINST - Ryobi DP102L | English Manual - Page 4
. WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe - Ryobi DP102L | English Manual - Page 5
column and head and table support collars are correctly positioned. BEFORE ENGAGING THE POWER SWITCH, MAKE SURE THE BELT GUARD IS DOWN AND THE CHUCK IS INSTALLED PROPERLY. LOCK THE MOTOR SWITCH OFF WHEN LEAVING THE DRILL PRESS. Do not perform layout, assembly, or set-up work on the table while - Ryobi DP102L | English Manual - Page 6
or use in damp locations. Read The Operator's Manual To reduce the risk of injury, user must read and understand operator's manual before using this product. Eye Protection Safety Alert No Hands Symbol Hot Surface Always wear safety goggles or safety glasses with side shields and a full face - Ryobi DP102L | English Manual - Page 7
servicing, use only identical replacement parts. WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing - Ryobi DP102L | English Manual - Page 8
motor's horsepower rating. A line intended only for lights cannot properly carry a power tool motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools. Grounding Instructions - Ryobi DP102L | English Manual - Page 9
A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90°. Compound Cut A drill presses) A small hole drilled in a workpiece that serves as a guide for drilling blades when the workpiece is not properly supported. Through Sawing Any cutting operation where the - Ryobi DP102L | English Manual - Page 10
. (RPM) Swing 10 in. Spindle Travel 2-3/8 in. Table Size 9-1/4 in. x 8-3/16 in. Table Movement 45° bevel, 360° swivel Overall Height 29 in. Net Weight 62 lbs. laser on/off switch depth gauge worklight worklight on/off switch switch key power switch chuck table laser bevel scale lock - Ryobi DP102L | English Manual - Page 11
and safety rules. bevel scale The bevel scale indicates the degree the table is tilted. Chuck Your drill press features a standard three-jaw type chuck with a self-ejecting chuck key, which prevents accidentally starting the drill press with the key still engaged in the chuck. exactline™ laser The - Ryobi DP102L | English Manual - Page 12
the drill press: Head Assembly 1 Column Assembly 1 Table Assembly 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Table Adjustment Handle 1 Table Lock Handle 1 AA Batteries 2 Chuck 1 Chuck Key 1 Worm Gear 1 Operator's Manual (not shown 1 aa batteries chuck KEY - Ryobi DP102L | English Manual - Page 13
requires assembly. Carefully remove the tool and any accessories from the box. Place it on a level work surface. Note: This tool is heavy. To for assistance. WARNING: If any parts are damaged or missing do not operate this tool until the missing parts are replaced. Failure to heed this warning - Ryobi DP102L | English Manual - Page 14
the shaft aligns with the set screw. Tighten the set screw using the hex key. Feed the gear rack through the slot in the table assembly so that end of the gear rack. Tighten the set screw in the collar using the hex key. Do not overtighten. NOTE: You should be able to move the table from side to - Ryobi DP102L | English Manual - Page 15
tighten the two head set screws with the hex key. Attach the three feed handles by screwing them into the threaded holes in the hub. Installing/changing worklight bulb See Figure 12. The integrated worklight can be used to help illuminate the work area. The worklight requires a 15-watt, 120-volt - Ryobi DP102L | English Manual - Page 16
changing laser batteries surface. The mounting board should be of sufficient size to avoid tipping while drill press is in use. Any good grade plywood or chipboard workbench. Once the drill press is securely mounted on a sturdy surface: Check for vibration when the motor is switched ON. Adjust - Ryobi DP102L | English Manual - Page 17
on a piece of scrap wood. Insert a small drill bit into the chuck and align its tip to the intersection of the lines of the "X". Secure the board to the table. Turn on the laser and verify the laser lines align with the "X" on the workpiece. If the laser lines do not align, loosen the set - Ryobi DP102L | English Manual - Page 18
or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: Drilling in wood Drilling in ceramics, plastics, fiberglass, and laminates Drilling in metals POWER SWITCH See Figure 16. The drill press is equipped - Ryobi DP102L | English Manual - Page 19
thrown from the drill press, resulting in possible serious personal injury or damage to the chuck. Tighten chuck jaws securely using chuck key provided. Do not use a wrench to tighten or loosen chuck jaws. ■ Remove chuck key. To remove the drill bit, reverse the steps listed above. TABLE LOCK - Ryobi DP102L | English Manual - Page 20
the bit; let the drill press do the work. Once the hole is completed, allow the spindle to return to its normal position. This will automatically raise the chuck and bit. DRILLING TIPS If a large hole is needed, it's a good idea to drill a smaller pilot hole before drilling the final one. Your - Ryobi DP102L | English Manual - Page 21
height and retighten the table lock handle. adjusting Table bevel See Figures 22 - 23. The drill press is equipped with a tilting table that allows you to drill to desired setting. Retighten lock knob securely using the hex key, if needed. bevel scale table adjustment handle table lock handle - Ryobi DP102L | English Manual - Page 22
for each drilling operation. To change the pulley configuration: Lift head assembly cover from front to open. Loosen the tension bolt. Remove the drive belt. Reposition the belt according to the speed chart. Retighten the tension bolt. drive belt SPINDLE PULLEY MOTOR PULLEY TENSION - Ryobi DP102L | English Manual - Page 23
servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety After using the drill press, clean it completely and lubricate all sliding and moving parts. Apply a light coat of automotivetype paste - Ryobi DP102L | English Manual - Page 24
troubleshooting Problem Noisy operation Bit burns or smokes Excessive drill runout or wobble Drill bit binds in workpiece Workpiece support loosens Possible Cause Solution Incorrect belt tension Dry spindle Loose spindle pulley or motor pulley Adjust belt tension. Lubricate spindle. Tighten set - Ryobi DP102L | English Manual - Page 25
NOTES 25 - Ryobi DP102L | English Manual - Page 26
OPERATOR'S MANUAL 10 in. DRILL PRESS DP102l • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
10 in. DRILL PRESS
DP102L